arm: rmobile: Add BLANCHE board support

BLANCHE is development board based on R-Car V2H SoC (R8A7792)

This commit supports the following periherals:
- SCIF, Ethernet, QSPI, MMC

Signed-off-by: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

1 files changed, 458 insertions, 0 deletions

diff --git a/board/renesas/blanche/blanche.c b/board/renesas/blanche/blanche.c
new file mode 100644
index 0000000..717c169
--- /dev/null
+++ b/board/renesas/blanche/blanche.c
@@ -0,0 +1,458 @@
+/*
+ * board/renesas/blanche/blanche.c
+ *     This file is blanche board support.
+ *
+ * Copyright (C) 2016 Renesas Electronics Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <netdev.h>
+#include <dm.h>
+#include <dm/platform_data/serial_sh.h>
+#include <asm/processor.h>
+#include <asm/mach-types.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/arch/rmobile.h>
+#include <asm/arch/rcar-mstp.h>
+#include <asm/arch/mmc.h>
+#include <asm/arch/sh_sdhi.h>
+#include <miiphy.h>
+#include <i2c.h>
+#include <mmc.h>
+#include "qos.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct pin_db {
+	u32	addr;	/* register address */
+	u32	mask;	/* mask value */
+	u32	val;	/* setting value */
+};
+
+#define	PMMR		0xE6060000
+#define	GPSR10		0xE606002C
+#define	PUPR3		0xE606010C
+#define	PUPR10		0xE6060128
+#define	PUPR11		0xE606012C
+
+#define	CPG_PLL1CR	0xE6150028
+#define	CPG_PLL3CR	0xE61500DC
+
+#define	SetREG(x) \
+	writel((readl((x)->addr) & ~((x)->mask)) | ((x)->val), (x)->addr)
+
+#define	SetGuardREG(x)				\
+{ \
+	u32	val; \
+	val = (readl((x)->addr) & ~((x)->mask)) | ((x)->val); \
+	writel(~val, PMMR); \
+	writel(val, (x)->addr); \
+}
+
+struct pin_db	pin_guard[] = {
+	{ GPSR10,	0xFFFFFFFF,	0x04006000 },
+};
+
+struct pin_db	pin_tbl[] = {
+	{ PUPR3,	0xFFFFFFFF,	0x0803FF40 },
+	{ PUPR10,	0xFFFFFFFF,	0xC0438001 },
+	{ PUPR11,	0xFFFFFFFF,	0x0FC00007 },
+};
+
+void pin_init(void)
+{
+	struct pin_db	*db;
+
+	for (db = pin_guard; db < &pin_guard[sizeof(pin_guard)/sizeof(struct pin_db)]; db++) {
+		SetGuardREG(db);
+	}
+	for (db = pin_tbl; db < &pin_tbl[sizeof(pin_tbl) /sizeof(struct pin_db)]; db++) {
+		SetREG(db);
+	}
+}
+
+#define s_init_wait(cnt) \
+		({	\
+			volatile u32 i = 0x10000 * cnt;	\
+			while (i > 0)	\
+				i--;	\
+		})
+
+void s_init(void)
+{
+	struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE;
+	struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE;
+	u32 cpu_type;
+
+	cpu_type = rmobile_get_cpu_type();
+	if (cpu_type == 0x4A) {
+		writel(0x4D000000, CPG_PLL1CR);
+		writel(0x4F000000, CPG_PLL3CR);
+	}
+
+	/* Watchdog init */
+	writel(0xA5A5A500, &rwdt->rwtcsra);
+	writel(0xA5A5A500, &swdt->swtcsra);
+
+	/* QoS(Quality-of-Service) Init */
+	qos_init();
+
+	/* SCIF Init */
+	pin_init();
+
+#if !defined(CONFIG_SYS_NO_FLASH)
+	struct rcar_lbsc *lbsc = (struct rcar_lbsc *)LBSC_BASE;
+	struct rcar_dbsc3 *dbsc3_0 = (struct rcar_dbsc3 *)DBSC3_0_BASE;
+
+	/* LBSC */
+	writel(0x00000020, &lbsc->cs0ctrl);
+	writel(0x00000020, &lbsc->cs1ctrl);
+	writel(0x00002020, &lbsc->ecs0ctrl);
+	writel(0x00002020, &lbsc->ecs1ctrl);
+
+	writel(0x2A103320, &lbsc->cswcr0);
+	writel(0x2A103320, &lbsc->cswcr1);
+	writel(0x19102110, &lbsc->ecswcr0);
+	writel(0x19102110, &lbsc->ecswcr1);
+
+	/* DBSC3 */
+	s_init_wait(10);
+
+	writel(0x0000A55A, &dbsc3_0->dbpdlck);
+
+	writel(0x21000000, &dbsc3_0->dbcmd);		/* opc=RstH (RESET => H) */
+	writel(0x11000000, &dbsc3_0->dbcmd);		/* opc=PDXt(CKE=H) */
+	writel(0x10000000, &dbsc3_0->dbcmd);		/* opc=PDEn(CKE=L) */
+
+	/* Stop Auto-Calibration */
+	writel(0x00000001, &dbsc3_0->dbpdrga);
+	writel(0x80000000, &dbsc3_0->dbpdrgd);
+
+	writel(0x00000004, &dbsc3_0->dbpdrga);
+	while ((readl(&dbsc3_0->dbpdrgd) & 0x00000001) != 0x00000001);
+
+	/* PLLCR: PLL Control Register */
+	writel(0x00000006, &dbsc3_0->dbpdrga);
+	writel(0x0001C000, &dbsc3_0->dbpdrgd);	// > DDR1440
+
+	/* DXCCR: DATX8 Common Configuration Register */
+	writel(0x0000000F, &dbsc3_0->dbpdrga);
+	writel(0x00181EE4, &dbsc3_0->dbpdrgd);
+
+	/* DSGCR	:DDR System General Configuration Register */
+	writel(0x00000010, &dbsc3_0->dbpdrga);
+	writel(0xF00464DB, &dbsc3_0->dbpdrgd);
+
+	writel(0x00000061, &dbsc3_0->dbpdrga);
+	writel(0x0000008D, &dbsc3_0->dbpdrgd);
+
+	/* Re-Execute ZQ calibration */
+	writel(0x00000001, &dbsc3_0->dbpdrga);
+	writel(0x00000073, &dbsc3_0->dbpdrgd);
+
+	writel(0x00000007, &dbsc3_0->dbkind);
+	writel(0x0F030A02, &dbsc3_0->dbconf0);
+	writel(0x00000001, &dbsc3_0->dbphytype);
+	writel(0x00000000, &dbsc3_0->dbbl);
+
+	writel(0x0000000B, &dbsc3_0->dbtr0);	// tCL=11
+	writel(0x00000008, &dbsc3_0->dbtr1);	// tCWL=8
+	writel(0x00000000, &dbsc3_0->dbtr2);	// tAL=0
+	writel(0x0000000B, &dbsc3_0->dbtr3);	// tRCD=11
+	writel(0x000C000B, &dbsc3_0->dbtr4);	// tRPA=12,tRP=11
+	writel(0x00000027, &dbsc3_0->dbtr5);	// tRC = 39
+	writel(0x0000001C, &dbsc3_0->dbtr6);	// tRAS = 28
+	writel(0x00000006, &dbsc3_0->dbtr7);	// tRRD = 6
+	writel(0x00000020, &dbsc3_0->dbtr8);	// tRFAW = 32
+	writel(0x00000008, &dbsc3_0->dbtr9);	// tRDPR = 8
+	writel(0x0000000C, &dbsc3_0->dbtr10);	// tWR = 12
+	writel(0x00000009, &dbsc3_0->dbtr11);	// tRDWR = 9
+	writel(0x00000012, &dbsc3_0->dbtr12);	// tWRRD = 18
+	writel(0x000000D0, &dbsc3_0->dbtr13);	// tRFC = 208
+	writel(0x00140005, &dbsc3_0->dbtr14);
+	writel(0x00050004, &dbsc3_0->dbtr15);
+	writel(0x70233005, &dbsc3_0->dbtr16);		/* DQL = 35, WDQL = 5 */
+	writel(0x000C0000, &dbsc3_0->dbtr17);
+	writel(0x00000300, &dbsc3_0->dbtr18);
+	writel(0x00000040, &dbsc3_0->dbtr19);
+	writel(0x00000001, &dbsc3_0->dbrnk0);
+	writel(0x00020001, &dbsc3_0->dbadj0);
+	writel(0x20082004, &dbsc3_0->dbadj2);		/* blanche QoS rev0.1 */
+	writel(0x00020002, &dbsc3_0->dbwt0cnf0);	/* 1600 */
+	writel(0x0000001F, &dbsc3_0->dbwt0cnf4);
+
+	while ((readl(&dbsc3_0->dbdfistat) & 0x00000001) != 0x00000001);
+	writel(0x00000011, &dbsc3_0->dbdficnt);
+
+	/* PGCR1	:PHY General Configuration Register 1 */
+	writel(0x00000003, &dbsc3_0->dbpdrga);
+	writel(0x0300C4E1, &dbsc3_0->dbpdrgd);		/* DDR3 */
+
+	/* PGCR2: PHY General Configuration Registers 2 */
+	writel(0x00000023, &dbsc3_0->dbpdrga);
+	writel(0x00FCDB60, &dbsc3_0->dbpdrgd);
+
+	writel(0x00000011, &dbsc3_0->dbpdrga);
+	writel(0x1000040B, &dbsc3_0->dbpdrgd);
+
+	/* DTPR0	:DRAM Timing Parameters Register 0 */
+	writel(0x00000012, &dbsc3_0->dbpdrga);
+	writel(0x9D9CBB66, &dbsc3_0->dbpdrgd);
+
+	/* DTPR1	:DRAM Timing Parameters Register 1 */
+	writel(0x00000013, &dbsc3_0->dbpdrga);
+	writel(0x1A868400, &dbsc3_0->dbpdrgd);
+
+	/* DTPR2	::DRAM Timing Parameters Register 2 */
+	writel(0x00000014, &dbsc3_0->dbpdrga);
+	writel(0x300214D8, &dbsc3_0->dbpdrgd);
+
+	/* MR0	:Mode Register 0 */
+	writel(0x00000015, &dbsc3_0->dbpdrga);
+	writel(0x00000D70, &dbsc3_0->dbpdrgd);
+
+	/* MR1	:Mode Register 1 */
+	writel(0x00000016, &dbsc3_0->dbpdrga);
+	writel(0x00000004, &dbsc3_0->dbpdrgd);	/* DRAM Drv 40ohm */
+
+	/* MR2	:Mode Register 2 */
+	writel(0x00000017, &dbsc3_0->dbpdrga);
+	writel(0x00000018, &dbsc3_0->dbpdrgd);	/* CWL=8 */
+
+	/* VREF(ZQCAL) */
+	writel(0x0000001A, &dbsc3_0->dbpdrga);
+	writel(0x910035C7, &dbsc3_0->dbpdrgd);
+
+	/* PGSR0	:PHY General Status Registers 0 */
+	writel(0x00000004, &dbsc3_0->dbpdrga);
+	while ((readl(&dbsc3_0->dbpdrgd) & 0x00000001) != 0x00000001);
+
+	/* DRAM Init (set MRx etc) */
+	writel(0x00000001, &dbsc3_0->dbpdrga);
+	writel(0x00000181, &dbsc3_0->dbpdrgd);
+
+	/* CKE  = H */
+	writel(0x11000000, &dbsc3_0->dbcmd);		/* opc=PDXt(CKE=H) */
+
+	/* PGSR0	:PHY General Status Registers 0 */
+	writel(0x00000004, &dbsc3_0->dbpdrga);
+	while ((readl(&dbsc3_0->dbpdrgd) & 0x00000001) != 0x00000001);
+
+	/* RAM ACC Training */
+	writel(0x00000001, &dbsc3_0->dbpdrga);
+	writel(0x0000FE01, &dbsc3_0->dbpdrgd);
+
+	/* Bus control 0 */
+	writel(0x00000000, &dbsc3_0->dbbs0cnt1);
+	/* DDR3 Calibration set */
+	writel(0x01004C20, &dbsc3_0->dbcalcnf);
+	/* DDR3 Calibration timing */
+	writel(0x014000AA, &dbsc3_0->dbcaltr);
+	/* Refresh */
+	writel(0x00000140, &dbsc3_0->dbrfcnf0);
+	writel(0x00081860, &dbsc3_0->dbrfcnf1);
+	writel(0x00010000, &dbsc3_0->dbrfcnf2);
+
+	/* PGSR0	:PHY General Status Registers 0 */
+	writel(0x00000004, &dbsc3_0->dbpdrga);
+	while ((readl(&dbsc3_0->dbpdrgd) & 0x00000001) != 0x00000001);
+
+	/* Enable Auto-Refresh */
+	writel(0x00000001, &dbsc3_0->dbrfen);
+	/* Permit DDR-Access */
+	writel(0x00000001, &dbsc3_0->dbacen);
+
+	/* This locks the access to the PHY unit registers */
+	writel(0x00000000, &dbsc3_0->dbpdlck);
+#endif /* CONFIG_SYS_NO_FLASH */
+
+}
+
+#define TMU0_MSTP125	(1 << 25)
+#define SCIF0_MSTP721	(1 << 21)
+#define SDHI0_MSTP314	(1 << 14)
+#define QSPI_MSTP917	(1 << 17)
+
+int board_early_init_f(void)
+{
+	/* TMU0 */
+	mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
+	/* SCIF0 */
+	mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721);
+	/* SDHI0 */
+	mstp_clrbits_le32(MSTPSR3, SMSTPCR3, SDHI0_MSTP314);
+	/* QSPI */
+	mstp_clrbits_le32(MSTPSR9, SMSTPCR9, QSPI_MSTP917);
+
+	return 0;
+}
+
+DECLARE_GLOBAL_DATA_PTR;
+int board_init(void)
+{
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+	/* Init PFC controller */
+	r8a7792_pinmux_init();
+
+	gpio_request(GPIO_FN_D0, NULL);
+	gpio_request(GPIO_FN_D1, NULL);
+	gpio_request(GPIO_FN_D2, NULL);
+	gpio_request(GPIO_FN_D3, NULL);
+	gpio_request(GPIO_FN_D4, NULL);
+	gpio_request(GPIO_FN_D5, NULL);
+	gpio_request(GPIO_FN_D6, NULL);
+	gpio_request(GPIO_FN_D7, NULL);
+	gpio_request(GPIO_FN_D8, NULL);
+	gpio_request(GPIO_FN_D9, NULL);
+	gpio_request(GPIO_FN_D10, NULL);
+	gpio_request(GPIO_FN_D11, NULL);
+	gpio_request(GPIO_FN_D12, NULL);
+	gpio_request(GPIO_FN_D13, NULL);
+	gpio_request(GPIO_FN_D14, NULL);
+	gpio_request(GPIO_FN_D15, NULL);
+	gpio_request(GPIO_FN_A0, NULL);
+	gpio_request(GPIO_FN_A1, NULL);
+	gpio_request(GPIO_FN_A2, NULL);
+	gpio_request(GPIO_FN_A3, NULL);
+	gpio_request(GPIO_FN_A4, NULL);
+	gpio_request(GPIO_FN_A5, NULL);
+	gpio_request(GPIO_FN_A6, NULL);
+	gpio_request(GPIO_FN_A7, NULL);
+	gpio_request(GPIO_FN_A8, NULL);
+	gpio_request(GPIO_FN_A9, NULL);
+	gpio_request(GPIO_FN_A10, NULL);
+	gpio_request(GPIO_FN_A11, NULL);
+	gpio_request(GPIO_FN_A12, NULL);
+	gpio_request(GPIO_FN_A13, NULL);
+	gpio_request(GPIO_FN_A14, NULL);
+	gpio_request(GPIO_FN_A15, NULL);
+	gpio_request(GPIO_FN_A16, NULL);
+	gpio_request(GPIO_FN_A17, NULL);
+	gpio_request(GPIO_FN_A18, NULL);
+	gpio_request(GPIO_FN_A19, NULL);
+#if defined(CONFIG_SYS_NO_FLASH)
+	gpio_request(GPIO_FN_MOSI_IO0, NULL);
+	gpio_request(GPIO_FN_MISO_IO1, NULL);
+	gpio_request(GPIO_FN_IO2, NULL);
+	gpio_request(GPIO_FN_IO3, NULL);
+	gpio_request(GPIO_FN_SPCLK, NULL);
+	gpio_request(GPIO_FN_SSL, NULL);
+#else	/* CONFIG_SYS_NO_FLASH */
+	gpio_request(GPIO_FN_A20, NULL);
+	gpio_request(GPIO_FN_A21, NULL);
+	gpio_request(GPIO_FN_A22, NULL);
+	gpio_request(GPIO_FN_A23, NULL);
+	gpio_request(GPIO_FN_A24, NULL);
+	gpio_request(GPIO_FN_A25, NULL);
+#endif	/* CONFIG_SYS_NO_FLASH */
+
+	gpio_request(GPIO_FN_CS1_A26, NULL);
+	gpio_request(GPIO_FN_EX_CS0, NULL);
+	gpio_request(GPIO_FN_EX_CS1, NULL);
+	gpio_request(GPIO_FN_BS, NULL);
+	gpio_request(GPIO_FN_RD, NULL);
+	gpio_request(GPIO_FN_WE0, NULL);
+	gpio_request(GPIO_FN_WE1, NULL);
+	gpio_request(GPIO_FN_EX_WAIT0, NULL);
+	gpio_request(GPIO_FN_IRQ0, NULL);
+	gpio_request(GPIO_FN_IRQ2, NULL);
+	gpio_request(GPIO_FN_IRQ3, NULL);
+	gpio_request(GPIO_FN_CS0, NULL);
+
+	/* Init timer */
+	timer_init();
+
+	return 0;
+}
+
+/*
+ Added for BLANCHE(R-CarV2H board)
+*/
+int board_eth_init(bd_t *bis)
+{
+	int rc = 0;
+
+#ifdef CONFIG_SMC911X
+#define STR_ENV_ETHADDR	"ethaddr"
+
+	struct eth_device *dev;
+	uchar eth_addr[6];
+
+	rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+
+	if (!eth_getenv_enetaddr(STR_ENV_ETHADDR, eth_addr)) {
+		dev = eth_get_dev_by_index(0);
+		if (dev) {
+			eth_setenv_enetaddr(STR_ENV_ETHADDR, dev->enetaddr);
+		} else {
+			printf("blanche: Couldn't get eth device\n");
+			rc = -1;
+		}
+	}
+
+#endif
+
+	return rc;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int ret = -ENODEV;
+
+#ifdef CONFIG_SH_SDHI
+	gpio_request(GPIO_FN_SD0_DAT0, NULL);
+	gpio_request(GPIO_FN_SD0_DAT1, NULL);
+	gpio_request(GPIO_FN_SD0_DAT2, NULL);
+	gpio_request(GPIO_FN_SD0_DAT3, NULL);
+	gpio_request(GPIO_FN_SD0_CLK, NULL);
+	gpio_request(GPIO_FN_SD0_CMD, NULL);
+	gpio_request(GPIO_FN_SD0_CD, NULL);
+
+	gpio_request(GPIO_GP_11_12, NULL);
+	gpio_direction_output(GPIO_GP_11_12, 1);	/* power on */
+
+
+	ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI0_BASE, 0,
+			   SH_SDHI_QUIRK_16BIT_BUF);
+
+	if (ret)
+		return ret;
+#endif
+	return ret;
+}
+
+int dram_init(void)
+{
+	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+	gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+const struct rmobile_sysinfo sysinfo = {
+	CONFIG_RMOBILE_BOARD_STRING
+};
+
+void reset_cpu(ulong addr)
+{
+}
+
+static const struct sh_serial_platdata serial_platdata = {
+	.base = SCIF0_BASE,
+	.type = PORT_SCIF,
+	.clk = 14745600,
+	.clk_mode = EXT_CLK,
+};
+
+U_BOOT_DEVICE(blanche_serials) = {
+	.name = "serial_sh",
+	.platdata = &serial_platdata,
+};