summaryrefslogtreecommitdiff
path: root/board/freescale/mpc8572ds/ddr.c
diff options
context:
space:
mode:
authorHaiying Wang <Haiying.Wang@freescale.com>2008-10-03 12:37:41 -0400
committerWolfgang Denk <wd@denx.de>2008-10-18 21:54:05 +0200
commit4ca06607d60d0a6378812ef58fd1eab2a7f77111 (patch)
treee145c64ad608f727c0d0f2cbcb54cbeca1c507eb /board/freescale/mpc8572ds/ddr.c
parent1f293b417ac6ab8e317ca2b770377ca93edf2370 (diff)
downloadu-boot-imx-4ca06607d60d0a6378812ef58fd1eab2a7f77111.zip
u-boot-imx-4ca06607d60d0a6378812ef58fd1eab2a7f77111.tar.gz
u-boot-imx-4ca06607d60d0a6378812ef58fd1eab2a7f77111.tar.bz2
Add ddr interleaving suppport for MPC8572DS board
* Add board specific parameter table to choose correct cpo, clk_adjust, write_data_delay, 2T based on board ddr frequency and n_ranks. * Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#. * Set memory controller interleaving mode to bank interleaving, and disable bank(chip select) interleaving mode by default, because the default on-board DDR DIMMs are 2x512MB single-rank. * Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Diffstat (limited to 'board/freescale/mpc8572ds/ddr.c')
-rw-r--r--board/freescale/mpc8572ds/ddr.c122
1 files changed, 94 insertions, 28 deletions
diff --git a/board/freescale/mpc8572ds/ddr.c b/board/freescale/mpc8572ds/ddr.c
index 435893a..d66ede2 100644
--- a/board/freescale/mpc8572ds/ddr.c
+++ b/board/freescale/mpc8572ds/ddr.c
@@ -39,42 +39,108 @@ void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
}
}
+typedef struct {
+ u32 datarate_mhz_low;
+ u32 datarate_mhz_high;
+ u32 n_ranks;
+ u32 clk_adjust;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2T;
+} board_specific_parameters_t;
+
+/* ranges for parameters:
+ * wr_data_delay = 0-6
+ * clk adjust = 0-8
+ * cpo 2-0x1E (30)
+ */
+
+
+/* XXX: these values need to be checked for all interleaving modes. */
+/* XXX: No reliable dual-rank 800 MHz setting has been found. It may
+ * seem reliable, but errors will appear when memory intensive
+ * program is run. */
+/* XXX: Single rank at 800 MHz is OK. */
+const board_specific_parameters_t board_specific_parameters[][20] = {
+ {
+ /* memory controller 0 */
+ /* lo| hi| num| clk| cpo|wrdata|2T */
+ /* mhz| mhz|ranks|adjst| | delay| */
+ { 0, 333, 2, 6, 7, 3, 0},
+ {334, 400, 2, 6, 9, 3, 0},
+ {401, 549, 2, 6, 11, 3, 0},
+ {550, 680, 2, 1, 10, 5, 0},
+ {681, 850, 2, 1, 12, 5, 1},
+ { 0, 333, 1, 6, 7, 3, 0},
+ {334, 400, 1, 6, 9, 3, 0},
+ {401, 549, 1, 6, 11, 3, 0},
+ {550, 680, 1, 1, 10, 5, 0},
+ {681, 850, 1, 1, 12, 5, 0}
+ },
+
+ {
+ /* memory controller 1 */
+ /* lo| hi| num| clk| cpo|wrdata|2T */
+ /* mhz| mhz|ranks|adjst| | delay| */
+ { 0, 333, 2, 6, 7, 3, 0},
+ {334, 400, 2, 6, 9, 3, 0},
+ {401, 549, 2, 6, 11, 3, 0},
+ {550, 680, 2, 1, 11, 6, 0},
+ {681, 850, 2, 1, 13, 6, 1},
+ { 0, 333, 1, 6, 7, 3, 0},
+ {334, 400, 1, 6, 9, 3, 0},
+ {401, 549, 1, 6, 11, 3, 0},
+ {550, 680, 1, 1, 11, 6, 0},
+ {681, 850, 1, 1, 13, 6, 0}
+ }
+};
+
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
- /*
- * Factors to consider for clock adjust:
- * - number of chips on bus
- * - position of slot
- * - DDR1 vs. DDR2?
- * - ???
- *
- * This needs to be determined on a board-by-board basis.
- * 0110 3/4 cycle late
- * 0111 7/8 cycle late
- */
- popts->clk_adjust = 7;
+ const board_specific_parameters_t *pbsp =
+ &(board_specific_parameters[ctrl_num][0]);
+ u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
+ sizeof(board_specific_parameters[0][0]);
+ u32 i;
+ ulong ddr_freq;
- /*
- * Factors to consider for CPO:
- * - frequency
- * - ddr1 vs. ddr2
+ /* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+ * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
+ * there are two dimms in the controller, set odt_rd_cfg to 3 and
+ * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
*/
- popts->cpo_override = 10;
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (i&1) { /* odd CS */
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 0;
+ } else { /* even CS */
+ if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
+ popts->cs_local_opts[i].odt_rd_cfg = 0;
+ popts->cs_local_opts[i].odt_wr_cfg = 4;
+ } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
+ popts->cs_local_opts[i].odt_rd_cfg = 3;
+ popts->cs_local_opts[i].odt_wr_cfg = 3;
+ }
+ }
+ }
- /*
- * Factors to consider for write data delay:
- * - number of DIMMs
- *
- * 1 = 1/4 clock delay
- * 2 = 1/2 clock delay
- * 3 = 3/4 clock delay
- * 4 = 1 clock delay
- * 5 = 5/4 clock delay
- * 6 = 3/2 clock delay
+ /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
*/
- popts->write_data_delay = 5;
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ for (i = 0; i < num_params; i++) {
+ if (ddr_freq >= pbsp->datarate_mhz_low &&
+ ddr_freq <= pbsp->datarate_mhz_high &&
+ pdimm->n_ranks == pbsp->n_ranks) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay = pbsp->write_data_delay;
+ popts->twoT_en = pbsp->force_2T;
+ }
+ pbsp++;
+ }
/*
* Factors to consider for half-strength driver enable: