Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  ARM: Add Calxeda Highbank platform
  dkb: make mmc command as default enabled
  Marvell: dkb: add mmc support
  ARM: pantheon: add mmc definition
  davinci: remove config.mk file from the sources
  ARM:AM33XX: Add support for TI AM335X EVM
  ARM:AM33XX: Added timer support
  ARM:AM33XX: Add emif/ddr support
  ARM:AM33XX: Add clock definitions
  ARM:AM33XX: Added support for AM33xx
  omap3/emif4: fix registers definition
  davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
  davinci: emac: add support for more than 1 PHYs
  davinci: emac: add new features to autonegotiate for EMAC
  da850evm: Move LPSC configuration to board_early_init_f()
  omap4_panda: Build in cmd_gpio support on panda
  omap: Don't use gpio_free to change direction to input
  mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
  OMAP3: overo : Add environment variable optargs to bootargs
  OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
  OMAP3: overo : Use ttyO2 instead of ttyS2.
  da830: add support for NAND boot mode
  dm36x: revert cache disable patch
  dm644X: revert cache disable patch
  devkit8000: Add malloc space
  omap: spl: fix build break due to changes in FAT
  OMAP3 SPL: Provide weak omap_rev_string
  omap: beagle: Use ubifs instead of jffs2 for nand boot
  omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
  omap: overo: Configure mux for gpio10
  SPL: Add DMA library
  omap3: Add interface for omap3 DMA
  omap3: Add DMA register accessors
  omap3: Add Base register for DMA
  arm, davinci: add missing LSPC define for MMC/SD1
  U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
  DaVinci: correct MDSTAT.STATE mask
  omap4: splitting padconfs into common, 4430 and 4460
  omap4: adding revision detection for 4460 ES1.1
  omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
  gplug: fixed build error as a result of code cleanup patch
  kirkwood_spi: add dummy spi_init()
  gpio: mvmfp: reduce include platform file
  ARM: orion5x: reduce dependence of including platform file
  serial: reduce include platform file for marvell chip
  ARM: kirkwood: reduce dependence of including platform file
  ARM: armada100: reduce dependence of including platform file
  ARM: pantheon: reduce dependence of including platform file
  Armada100: Add env storage support for Marvell gplugD
  Armada100: Add SPI flash support for Marvell gplugD
  Armada100: Add SPI support for Marvell gplugD
  SPI: Add SPI driver support for Marvell Armada100
  dreamplug: initial board support.
  imx: fix coding style
  misc: pmic: drop old Freescale's pmic driver
  MX31: mx31pdk: use new pmic driver
  MX31: mx31ads: use new pmic driver
  MX31: mx31_litekit: use new pmic driver
  MX5: mx53evk: use new pmic driver
  MX5: mx51evk: use new pmic driver
  MX35: mx35pdk: use new pmic driver
  misc: pmic: addI2C  support to pmic_fsl driver
  misc: pmic: use I2C_SET_BUS in pmic I2C
  MX5: efikamx/efikasb: use new pmic driver
  MX3: qong: use new pmic driver
  RTC: Switch mc13783 to generic pmic code
  MX5: vision2: use new pmic driver
  misc: pmic: Freescale PMIC switches to generic PMIC driver
  misc:pmic:samsung Enable PMIC driver at GONI target
  misc:pmic:max8998 MAX8998 support at a new PMIC driver.
  misc:pmic:core New generic PMIC driver
  mx31pdk: Remove unneeded config
  mx31: provide readable WEIM CS accessor
  MX51: vision2: Set global macros
  I2C: Add i2c_get/set_speed() to mxc_i2c.c
  ARM: Update mach-types
  devkit8000: Add config to enable SPL MMC boot
  devkit8000: protect board_mmc_init
  arm, post: add missing post_time_ms for arm
  cosmetic, post: Codingstyle cleanup
  arm, logbuffer: make it compileclean
  tegra2: Enable MMC for Seaboard
  tegra2: Add more pinmux functions
  tegra2: Rename PIN_ to PINGRP_
  tegra2: Add more clock functions
  tegra2: Clean up board code a little
  tegra2: Rename CLOCK_PLL_ID to CLOCK_ID

1 files changed, 163 insertions, 0 deletions

diff --git a/board/Marvell/dreamplug/kwbimage.cfg b/board/Marvell/dreamplug/kwbimage.cfg
new file mode 100644
index 0000000..ca9cd74
--- /dev/null
+++ b/board/Marvell/dreamplug/kwbimage.cfg
@@ -0,0 +1,163 @@
+#
+# (C) Copyright 2011
+# Jason Cooper <u-boot@lakedaemon.net>
+#
+# Based on work by:
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Siddarth Gore <gores@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	spi
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0/1 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b9b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30	# DDR Configuration register
+# bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000	# DDR Controller Control Low
+# bit 4:    0=addr/cmd in smame cycle
+# bit 5:    0=clk is driven during self refresh, we don't care for APX
+# bit 6:    0=use recommended falling edge of clk for addr/cmd
+# bit14:    0=input buffer always powered up
+# bit18:    1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31:    0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
+# bit3-0:   TRAS lsbs
+# bit7-4:   TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20:    TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33	#  DDR Timing (High)
+# bit6-0:   TRFC
+# bit8-7:   TR2R
+# bit10-9:  TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x000000cc	#  DDR Address Control
+# bit1-0:   01, Cs0width=x8
+# bit3-2:   10, Cs0size=1Gb
+# bit5-4:   01, Cs1width=x8
+# bit7-6:   10, Cs1size=1Gb
+# bit9-8:   00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16:    0,  Cs0AddrSel
+# bit17:    0,  Cs1AddrSel
+# bit18:    0,  Cs2AddrSel
+# bit19:    0,  Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
+# bit0:    0,  OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000	#  DDR Operation
+# bit3-0:   0x0, DDR cmd
+# bit31-4:  0 required
+
+DATA 0xFFD0141C 0x00000C52	#  DDR Mode
+# bit2-0:   2, BurstLen=2 required
+# bit3:     0, BurstType=0 required
+# bit6-4:   4, CL=5
+# bit7:     0, TestMode=0 normal
+# bit8:     0, DLL reset=0 normal
+# bit11-9:  6, auto-precharge write recovery ????????????
+# bit12:    0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000040	#  DDR Extended Mode
+# bit0:    0,  DDR DLL enabled
+# bit1:    0,  DDR drive strenght normal
+# bit2:    0,  DDR ODT control lsd (disabled)
+# bit5-3:  000, required
+# bit6:    1,  DDR ODT control msb, (disabled)
+# bit9-7:  000, required
+# bit10:   0,  differential DQS enabled
+# bit11:   0, required
+# bit12:   0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
+# bit2-0:  111, required
+# bit3  :  1  , MBUS Burst Chop disabled
+# bit6-4:  111, required
+# bit7  :  0
+# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9  :  0  , no half clock cycle addition to dataout
+# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0    required
+
+DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
+# bit0:    1,  Window enabled
+# bit1:    0,  Write Protect disabled
+# bit3-2:  00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000	# CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x0FFFFFF5	# CS[1]n Size 256Mb Window enabled for CS1
+
+DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00030000	#  DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
+# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
+# bit3-2:  01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E803	# CPU ODT Control
+DATA 0xFFD01480 0x00000001	# DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0