sunxi: Fix gmac not working due to cpu_eth_init no longer being called

cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work in u-boot.

This commit fixes this by calling the clock, reset and pinmux setup
function from s_init() and enabling the phy power pin (if any) from
board_init().

The enabling of phy power cannot be done from s_init because it uses dm
and dm is not ready yet at this point.

Note that the mdelay is dropped as the phy gets enabled much earlier
now, so it is no longer needed.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Michael Haas <haas@computerlinguist.org>

4 files changed, 12 insertions, 41 deletions

diff --git a/arch/arm/cpu/armv7/sunxi/board.c b/arch/arm/cpu/armv7/sunxi/board.c
index e80785b..7653148 100644
--- a/arch/arm/cpu/armv7/sunxi/board.c
+++ b/arch/arm/cpu/armv7/sunxi/board.c
@@ -152,6 +152,7 @@ void s_init(void)
 	timer_init();
 	gpio_init();
 	i2c_init_board();
+	eth_init_board();
 }
 
 #ifdef CONFIG_SPL_BUILD
@@ -259,30 +260,3 @@ void enable_caches(void)
 	dcache_enable();
 }
 #endif
-
-#ifdef CONFIG_CMD_NET
-/*
- * Initializes on-chip ethernet controllers.
- * to override, implement board_eth_init()
- */
-int cpu_eth_init(bd_t *bis)
-{
-	__maybe_unused int rc;
-
-#ifdef CONFIG_MACPWR
-	gpio_request(CONFIG_MACPWR, "macpwr");
-	gpio_direction_output(CONFIG_MACPWR, 1);
-	mdelay(200);
-#endif
-
-#ifdef CONFIG_SUNXI_GMAC
-	rc = sunxi_gmac_initialize(bis);
-	if (rc < 0) {
-		printf("sunxi: failed to initialize gmac\n");
-		return rc;
-	}
-#endif
-
-	return 0;
-}
-#endif
diff --git a/arch/arm/include/asm/arch-sunxi/sys_proto.h b/arch/arm/include/asm/arch-sunxi/sys_proto.h
index 9df3744..a373319 100644
--- a/arch/arm/include/asm/arch-sunxi/sys_proto.h
+++ b/arch/arm/include/asm/arch-sunxi/sys_proto.h
@@ -24,6 +24,10 @@ void sdelay(unsigned long);
 void return_to_fel(uint32_t lr, uint32_t sp);
 
 /* Board / SoC level designware gmac init */
-int sunxi_gmac_initialize(bd_t *bis);
+#if !defined CONFIG_SPL_BUILD && defined CONFIG_SUNXI_GMAC
+void eth_init_board(void);
+#else
+static inline void eth_init_board(void) {}
+#endif
 
 #endif
diff --git a/board/sunxi/board.c b/board/sunxi/board.c
index 80eae9c..e16718f 100644
--- a/board/sunxi/board.c
+++ b/board/sunxi/board.c
@@ -90,6 +90,11 @@ int board_init(void)
 	if (ret)
 		return ret;
 
+#ifdef CONFIG_MACPWR
+	gpio_request(CONFIG_MACPWR, "macpwr");
+	gpio_direction_output(CONFIG_MACPWR, 1);
+#endif
+
 	/* Uses dm gpio code so do this here and not in i2c_init_board() */
 	return soft_i2c_board_init();
 }
diff --git a/board/sunxi/gmac.c b/board/sunxi/gmac.c
index 4e222d8..69eb8ff 100644
--- a/board/sunxi/gmac.c
+++ b/board/sunxi/gmac.c
@@ -6,7 +6,7 @@
 #include <asm/arch/clock.h>
 #include <asm/arch/gpio.h>
 
-int sunxi_gmac_initialize(bd_t *bis)
+void eth_init_board(void)
 {
 	int pin;
 	struct sunxi_ccm_reg *const ccm =
@@ -79,16 +79,4 @@ int sunxi_gmac_initialize(bd_t *bis)
 	for (pin = SUNXI_GPA(26); pin <= SUNXI_GPA(27); pin++)
 		sunxi_gpio_set_cfgpin(pin, SUN6I_GPA_GMAC);
 #endif
-
-#ifdef CONFIG_DM_ETH
-	return 0;
-#else
-# ifdef CONFIG_RGMII
-	return designware_initialize(SUNXI_GMAC_BASE, PHY_INTERFACE_MODE_RGMII);
-# elif defined CONFIG_GMII
-	return designware_initialize(SUNXI_GMAC_BASE, PHY_INTERFACE_MODE_GMII);
-# else
-	return designware_initialize(SUNXI_GMAC_BASE, PHY_INTERFACE_MODE_MII);
-# endif
-#endif
 }