Migrate esd 405EP boards to new NAND subsystem

Migrate esd 405EP boards to new NAND subsystem

-cleanup
-use correct io accessors (in/out_be32())

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

21 files changed, 120 insertions, 456 deletions

diff --git a/board/esd/ash405/Makefile b/board/esd/ash405/Makefile
index 4d75868..308f752 100644
--- a/board/esd/ash405/Makefile
+++ b/board/esd/ash405/Makefile
@@ -28,7 +28,9 @@ endif
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	= $(BOARD).o flash.o ../common/misc.o
+COBJS	= $(BOARD).o flash.o \
+	../common/misc.o \
+	../common/esd405ep_nand.o \
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/board/esd/ash405/ash405.c b/board/esd/ash405/ash405.c
index 84fc3a0..0151d74 100644
--- a/board/esd/ash405/ash405.c
+++ b/board/esd/ash405/ash405.c
@@ -23,6 +23,7 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/io.h>
 #include <command.h>
 #include <malloc.h>
 
@@ -33,6 +34,7 @@
 #endif
 
 extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+extern void lxt971_no_sleep(void);
 
 /* fpga configuration data - gzip compressed and generated by bin2c */
 const unsigned char fpgadata[] =
@@ -164,18 +166,12 @@ int misc_init_r (void)
 	/*
 	 * Reset external DUARTs
 	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
+	out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_DUART_RST);
 	udelay(10); /* wait 10us */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
+	out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_DUART_RST);
 	udelay(1000); /* wait 1ms */
 
 	/*
-	 * Set NAND-FLASH GPIO signals to default
-	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
-	/*
 	 * Enable interrupts in exar duart mcr[3]
 	 */
 	*duart0_mcr = 0x08;
@@ -218,35 +214,18 @@ long int initdram (int board_type)
 	mtdcr(memcfga, mem_mb0cf);
 	val = mfdcr(memcfgd);
 
-#if 0
-	printf("\nmb0cf=%x\n", val); /* test-only */
-	printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
 	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
 }
 
 /* ------------------------------------------------------------------------- */
 
-int testdram (void)
+void reset_phy(void)
 {
-	/* TODO: XXX XXX XXX */
-	printf ("test: 16 MB - ok\n");
-
-	return (0);
-}
+#ifdef CONFIG_LXT971_NO_SLEEP
 
-/* ------------------------------------------------------------------------- */
-
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-	nand_probe(CFG_NAND_BASE);
-	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-		print_size(nand_dev_desc[0].totlen, "\n");
-	}
-}
+	/*
+	 * Disable sleep mode in LXT971
+	 */
+	lxt971_no_sleep();
 #endif
+}
diff --git a/board/esd/cms700/Makefile b/board/esd/cms700/Makefile
index df48766..0d4ab2d 100644
--- a/board/esd/cms700/Makefile
+++ b/board/esd/cms700/Makefile
@@ -33,7 +33,10 @@ CPLD    = ../common/xilinx_jtag/lenval.o \
 	  ../common/xilinx_jtag/micro.o \
 	  ../common/xilinx_jtag/ports.o
 
-COBJS	= $(BOARD).o flash.o ../common/misc.o $(CPLD)
+COBJS	= $(BOARD).o flash.o \
+	../common/misc.o \
+	$(CPLD) \
+	../common/esd405ep_nand.o \
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/board/esd/cms700/cms700.c b/board/esd/cms700/cms700.c
index cb04710..2cdd7be 100644
--- a/board/esd/cms700/cms700.c
+++ b/board/esd/cms700/cms700.c
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2005
+ * (C) Copyright 2005-2007
  * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
  *
  * See file CREDITS for list of people who contributed to this
@@ -23,6 +23,7 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/io.h>
 #include <command.h>
 #include <malloc.h>
 
@@ -68,9 +69,9 @@ int board_early_init_f (void)
 	/*
 	 * Reset CPLD via GPIO12 (CS3) pin
 	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_PLD_RESET);
+	out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_PLD_RESET);
 	udelay(1000); /* wait 1ms */
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_PLD_RESET);
+	out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_PLD_RESET);
 	udelay(1000); /* wait 1ms */
 
 	return 0;
@@ -94,13 +95,7 @@ int misc_init_r (void)
  	/*
 	 * Setup and enable EEPROM write protection
 	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
-
-	/*
-	 * Set NAND-FLASH GPIO signals to default
-	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
+	out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_EEPROM_WP);
 
 	return (0);
 }
@@ -153,11 +148,6 @@ long int initdram (int board_type)
 	mtdcr(memcfga, mem_mb0cf);
 	val = mfdcr(memcfgd);
 
-#if 0
-	printf("\nmb0cf=%x\n", val); /* test-only */
-	printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
 	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
 }
 
@@ -180,17 +170,17 @@ int eeprom_write_enable (unsigned dev_addr, int state)
 		switch (state) {
 		case 1:
 			/* Enable write access, clear bit GPIO_SINT2. */
-			out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_EEPROM_WP);
+			out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_EEPROM_WP);
 			state = 0;
 			break;
 		case 0:
 			/* Disable write access, set bit GPIO_SINT2. */
-			out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
+			out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_EEPROM_WP);
 			state = 0;
 			break;
 		default:
 			/* Read current status back. */
-			state = (0 == (in32(GPIO0_OR) & CFG_EEPROM_WP));
+			state = (0 == (in_be32((void *)GPIO0_OR) & CFG_EEPROM_WP));
 			break;
 		}
 	}
@@ -235,19 +225,6 @@ U_BOOT_CMD(eepwren,	2,	0,	do_eep_wren,
 
 /* ------------------------------------------------------------------------- */
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-	nand_probe(CFG_NAND_BASE);
-	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-		print_size(nand_dev_desc[0].totlen, "\n");
-	}
-}
-#endif
-
 void reset_phy(void)
 {
 #ifdef CONFIG_LXT971_NO_SLEEP
diff --git a/board/esd/hh405/Makefile b/board/esd/hh405/Makefile
index ce7876c..0e5e57a 100644
--- a/board/esd/hh405/Makefile
+++ b/board/esd/hh405/Makefile
@@ -28,7 +28,10 @@ endif
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	= $(BOARD).o flash.o ../common/misc.o ../common/auto_update.o
+COBJS	= $(BOARD).o flash.o \
+	../common/misc.o \
+	../common/esd405ep_nand.o \
+	../common/auto_update.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/board/esd/hh405/hh405.c b/board/esd/hh405/hh405.c
index ea344c0..67b5d54 100644
--- a/board/esd/hh405/hh405.c
+++ b/board/esd/hh405/hh405.c
@@ -5,7 +5,7 @@
  * (C) Copyright 2005
  * Stefan Roese, DENX Software Engineering, sr@denx.de.
  *
- * (C) Copyright 2006
+ * (C) Copyright 2006-2007
  * Matthias Fuchs, esd GmbH, matthias.fuchs@esd-electronics.com
  *
  * See file CREDITS for list of people who contributed to this
@@ -477,12 +477,6 @@ int misc_init_r (void)
 	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_EEPROM_WP);
 
 	/*
-	 * Set NAND-FLASH GPIO signals to default
-	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
-	/*
 	 * Reset touch-screen controller
 	 */
 	out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_TOUCH_RST);
@@ -690,20 +684,6 @@ void ide_set_reset(int on)
 #endif /* CONFIG_IDE_RESET */
 
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-	nand_probe(CFG_NAND_BASE);
-	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-		print_size(nand_dev_desc[0].totlen, "\n");
-	}
-}
-#endif
-
-
 #if defined(CFG_EEPROM_WREN)
 /* Input: <dev_addr>  I2C address of EEPROM device to enable.
  *         <state>     -1: deliver current state
diff --git a/board/esd/hub405/Makefile b/board/esd/hub405/Makefile
index 4d75868..308f752 100644
--- a/board/esd/hub405/Makefile
+++ b/board/esd/hub405/Makefile
@@ -28,7 +28,9 @@ endif
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	= $(BOARD).o flash.o ../common/misc.o
+COBJS	= $(BOARD).o flash.o \
+	../common/misc.o \
+	../common/esd405ep_nand.o \
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/board/esd/hub405/hub405.c b/board/esd/hub405/hub405.c
index 1e0accb..25c8068 100644
--- a/board/esd/hub405/hub405.c
+++ b/board/esd/hub405/hub405.c
@@ -153,12 +153,6 @@ int misc_init_r (void)
 	out32(GPIO0_OR, val);
 
 	/*
-	 * Set NAND-FLASH GPIO signals to default
-	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
-	/*
 	 * check board type and setup AP power
 	 */
 	str = getenv("bd_type"); /* this is only set on non prototype hardware */
@@ -242,33 +236,5 @@ long int initdram (int board_type)
 	mtdcr(memcfga, mem_mb0cf);
 	val = mfdcr(memcfgd);
 
-#if 0
-	printf("\nmb0cf=%x\n", val); /* test-only */
-	printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
 	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
 }
-
-
-int testdram (void)
-{
-	/* TODO: XXX XXX XXX */
-	printf ("test: 16 MB - ok\n");
-
-	return (0);
-}
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-	nand_probe(CFG_NAND_BASE);
-	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-		print_size(nand_dev_desc[0].totlen, "\n");
-	}
-}
-#endif
diff --git a/board/esd/plu405/Makefile b/board/esd/plu405/Makefile
index ce7876c..0e5e57a 100644
--- a/board/esd/plu405/Makefile
+++ b/board/esd/plu405/Makefile
@@ -28,7 +28,10 @@ endif
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	= $(BOARD).o flash.o ../common/misc.o ../common/auto_update.o
+COBJS	= $(BOARD).o flash.o \
+	../common/misc.o \
+	../common/esd405ep_nand.o \
+	../common/auto_update.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/board/esd/plu405/plu405.c b/board/esd/plu405/plu405.c
index 59171f8..f026a7a 100644
--- a/board/esd/plu405/plu405.c
+++ b/board/esd/plu405/plu405.c
@@ -23,6 +23,7 @@
 
 #include <common.h>
 #include <asm/processor.h>
+#include <asm/io.h>
 #include <command.h>
 #include <malloc.h>
 
@@ -31,6 +32,8 @@
 #define FPGA_DEBUG
 #endif
 
+DECLARE_GLOBAL_DATA_PTR;
+
 extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
 extern void lxt971_no_sleep(void);
 
@@ -114,6 +117,10 @@ int misc_init_r (void)
 	int index;
 	int i;
 
+	/* adjust flash start and offset */
+	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
+	gd->bd->bi_flashoffset = 0;
+
 	dst = malloc(CFG_FPGA_MAX_SIZE);
 	if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
 		printf ("GUNZIP ERROR - must RESET board to recover\n");
@@ -177,18 +184,12 @@ int misc_init_r (void)
 	/*
 	 * Reset external DUARTs
 	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
+	out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_DUART_RST);
 	udelay(10); /* wait 10us */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
+	out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_DUART_RST);
 	udelay(1000); /* wait 1ms */
 
 	/*
-	 * Set NAND-FLASH GPIO signals to default
-	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
-	/*
 	 * Enable interrupts in exar duart mcr[3]
 	 */
 	*duart0_mcr = 0x08;
@@ -226,24 +227,10 @@ long int initdram (int board_type)
 	mtdcr(memcfga, mem_mb0cf);
 	val = mfdcr(memcfgd);
 
-#if 0
-	printf("\nmb0cf=%x\n", val); /* test-only */
-	printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
 	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
 }
 
 
-int testdram (void)
-{
-	/* TODO: XXX XXX XXX */
-	printf ("test: 16 MB - ok\n");
-
-	return (0);
-}
-
-
 #ifdef CONFIG_IDE_RESET
 void ide_set_reset(int on)
 {
@@ -262,31 +249,6 @@ void ide_set_reset(int on)
 #endif /* CONFIG_IDE_RESET */
 
 
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-	nand_probe(CFG_NAND_BASE);
-	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-		print_size(nand_dev_desc[0].totlen, "\n");
-	}
-}
-#endif
-
-
-#ifdef CONFIG_AUTO_UPDATE_SHOW
-void board_auto_update_show(int au_active)
-{
-	if (au_active) {
-		printf("\n Dies ist die board-funktion: Updating!!!\n");
-	} else {
-		printf("\n Dies ist die board-funktion: Updating done!!!\n");
-	}
-}
-#endif
-
 void reset_phy(void)
 {
 #ifdef CONFIG_LXT971_NO_SLEEP
diff --git a/board/esd/voh405/Makefile b/board/esd/voh405/Makefile
index 4d75868..308f752 100644
--- a/board/esd/voh405/Makefile
+++ b/board/esd/voh405/Makefile
@@ -28,7 +28,9 @@ endif
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	= $(BOARD).o flash.o ../common/misc.o
+COBJS	= $(BOARD).o flash.o \
+	../common/misc.o \
+	../common/esd405ep_nand.o \
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/board/esd/voh405/voh405.c b/board/esd/voh405/voh405.c
index 22995b5..2857a0be 100644
--- a/board/esd/voh405/voh405.c
+++ b/board/esd/voh405/voh405.c
@@ -195,12 +195,6 @@ int misc_init_r (void)
 	udelay(1000); /* wait 1ms */
 
 	/*
-	 * Set NAND-FLASH GPIO signals to default
-	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
-	/*
 	 * Enable interrupts in exar duart mcr[3]
 	 */
 	*duart0_mcr = 0x08;
@@ -340,17 +334,3 @@ void ide_set_reset(int on)
 	}
 }
 #endif /* CONFIG_IDE_RESET */
-
-
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-	nand_probe(CFG_NAND_BASE);
-	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-		print_size(nand_dev_desc[0].totlen, "\n");
-	}
-}
-#endif
diff --git a/board/esd/wuh405/Makefile b/board/esd/wuh405/Makefile
index 4d75868..308f752 100644
--- a/board/esd/wuh405/Makefile
+++ b/board/esd/wuh405/Makefile
@@ -28,7 +28,9 @@ endif
 
 LIB	= $(obj)lib$(BOARD).a
 
-COBJS	= $(BOARD).o flash.o ../common/misc.o
+COBJS	= $(BOARD).o flash.o \
+	../common/misc.o \
+	../common/esd405ep_nand.o \
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS))
diff --git a/board/esd/wuh405/wuh405.c b/board/esd/wuh405/wuh405.c
index 5a1a3f3..0b53062 100644
--- a/board/esd/wuh405/wuh405.c
+++ b/board/esd/wuh405/wuh405.c
@@ -170,12 +170,6 @@ int misc_init_r (void)
 	udelay(1000); /* wait 1ms */
 
 	/*
-	 * Set NAND-FLASH GPIO signals to default
-	 */
-	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
-	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
-
-	/*
 	 * Enable interrupts in exar duart mcr[3]
 	 */
 	*duart0_mcr = 0x08;
@@ -218,35 +212,8 @@ long int initdram (int board_type)
 	mtdcr(memcfga, mem_mb0cf);
 	val = mfdcr(memcfgd);
 
-#if 0
-	printf("\nmb0cf=%x\n", val); /* test-only */
-	printf("strap=%x\n", mfdcr(strap)); /* test-only */
-#endif
-
 	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
 }
 
 /* ------------------------------------------------------------------------- */
 
-int testdram (void)
-{
-	/* TODO: XXX XXX XXX */
-	printf ("test: 16 MB - ok\n");
-
-	return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#include <linux/mtd/nand_legacy.h>
-extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
-
-void nand_init(void)
-{
-	nand_probe(CFG_NAND_BASE);
-	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
-		print_size(nand_dev_desc[0].totlen, "\n");
-	}
-}
-#endif
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h
index d03c05b..584f490 100644
--- a/include/configs/ASH405.h
+++ b/include/configs/ASH405.h
@@ -53,9 +53,13 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+#define CONFIG_NET_MULTI	1
+#undef  CONFIG_HAS_ETH1
+
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
@@ -132,39 +136,16 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
 
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1  /* verify all writes!!!         */
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
 /*-----------------------------------------------------------------------
diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h
index 1cca285..9695211 100644
--- a/include/configs/CMS700.h
+++ b/include/configs/CMS700.h
@@ -81,8 +81,6 @@
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#define CFG_NAND_LEGACY
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
@@ -148,34 +146,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
diff --git a/include/configs/HH405.h b/include/configs/HH405.h
index dc40ebc..f36777a 100644
--- a/include/configs/HH405.h
+++ b/include/configs/HH405.h
@@ -130,8 +130,6 @@
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#define CFG_NAND_LEGACY
-
 #undef  CONFIG_BZIP2	 /* include support for bzip2 compressed images */
 #undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -198,34 +196,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
index f84e356..88cc6a4 100644
--- a/include/configs/HUB405.h
+++ b/include/configs/HUB405.h
@@ -135,36 +135,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index d02c39b..ef5ecba 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -81,7 +81,6 @@
 #define CONFIG_SUPPORT_VFAT
 
 #define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
-#define CONFIG_AUTO_UPDATE_SHOW 1       /* use board show routine       */
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
@@ -156,36 +155,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
 
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
@@ -264,11 +242,6 @@
 
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
-#endif
-
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
@@ -294,9 +267,6 @@
 #define CFG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC16 is 2048 bytes */
 
-#define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
-#define CFG_NVRAM_SIZE		242			/* NVRAM size		*/
-
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
@@ -305,7 +275,7 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
-#if 1 /* test-only */
+
 /* CAT24WC08/16... */
 #define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"	*/
@@ -313,15 +283,6 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
 					/* last 4 bits of the address	*/
-#else
-/* CAT24WC32/64... */
-#define CFG_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x01
-#define CFG_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
-					/* 32 byte page write mode using*/
-					/* last 5 bits of the address	*/
-#endif
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h
index 96f3d26..abd1ef4 100644
--- a/include/configs/VOH405.h
+++ b/include/configs/VOH405.h
@@ -141,36 +141,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h
index faf855d..52bff40 100644
--- a/include/configs/WUH405.h
+++ b/include/configs/WUH405.h
@@ -133,38 +133,16 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1  /* verify all writes!!!         */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
+
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
 /*-----------------------------------------------------------------------