summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorPaul Gortmaker <paul.gortmaker@windriver.com>2011-12-30 23:53:10 -0500
committerKumar Gala <galak@kernel.crashing.org>2012-01-11 13:59:07 -0600
commit7e44f2b710db09a1b02e55246e0915732cc4775e (patch)
treee94b2b4fa41c941841bcb5b61214e3b9b82f12d3
parent5f4c6f0db930646e9ca3b479b5fe9b8d2691fa77 (diff)
downloadu-boot-imx-7e44f2b710db09a1b02e55246e0915732cc4775e.zip
u-boot-imx-7e44f2b710db09a1b02e55246e0915732cc4775e.tar.gz
u-boot-imx-7e44f2b710db09a1b02e55246e0915732cc4775e.tar.bz2
sbc8548: Make enabling SPD RAM configuration work
Previously, SPD configuration of RAM was non functional on this board. Now that the root cause is known (an i2c address conflict), there is a simple end-user workaround - remove the old slower local bus 128MB module and then SPD detection on the main DDR2 memory module works fine. We make the enablement of the LBC SDRAM support conditional on being not SPD enabled. We can revisit this dependency as the hardware workaround becomes available. Turning off LBC SDRAM support revealed a couple implict dependencies in the tlb/law code that always expected an LBC SDRAM address. This has been tested with the default 256MB module, a 512MB a 1GB and a 2GB, of varying speeds, and the SPD autoconfiguration worked fine in all cases. The default configuration remains to go with the hard coded DDR config, so the default build will continue to work on boards where people don't bother to read the docs. But the advantage of going to the SPD config is that even the small default module gets configured for CL3 instead of CL4. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
-rw-r--r--board/sbc8548/law.c5
-rw-r--r--board/sbc8548/tlb.c2
-rw-r--r--doc/README.sbc854821
-rw-r--r--include/configs/sbc8548.h13
4 files changed, 40 insertions, 1 deletions
diff --git a/board/sbc8548/law.c b/board/sbc8548/law.c
index c263191..322af76 100644
--- a/board/sbc8548/law.c
+++ b/board/sbc8548/law.c
@@ -59,8 +59,13 @@ struct law_entry law_table[] = {
#ifndef CONFIG_SPD_EEPROM
SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR),
#endif
+#ifdef CONFIG_SYS_LBC_SDRAM_BASE
/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+#else
+ /* LBC window - maps 128M 0xf8000000 -> 0xffffffff */
+ SET_LAW(CONFIG_SYS_EPLD_BASE, LAW_SIZE_128M, LAW_TRGT_IF_LBC),
+#endif
};
int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/sbc8548/tlb.c b/board/sbc8548/tlb.c
index 4bf7214..af927f1 100644
--- a/board/sbc8548/tlb.c
+++ b/board/sbc8548/tlb.c
@@ -76,6 +76,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 2, BOOKE_PAGESZ_64M, 1),
+#ifdef CONFIG_SYS_LBC_SDRAM_BASE
/*
* TLB 3: 64M Cacheable, non-guarded
* 0xf0000000 64M LBC SDRAM First half
@@ -92,6 +93,7 @@ struct fsl_e_tlb_entry tlb_table[] = {
CONFIG_SYS_LBC_SDRAM_BASE + 0x4000000,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 4, BOOKE_PAGESZ_64M, 1),
+#endif
/*
* TLB 5: 16M Cacheable, non-guarded
diff --git a/doc/README.sbc8548 b/doc/README.sbc8548
index e6b8abe..f9e2dea 100644
--- a/doc/README.sbc8548
+++ b/doc/README.sbc8548
@@ -62,6 +62,27 @@ a 33MHz PCI configuration is currently untested.)
02.00.00 0x1148 0x9e00 Network controller 0x00
=>
+Memory Size and using SPD:
+==========================
+
+The default configuration uses hard coded memory configuration settings
+for 256MB of DDR2 @400MHz. It does not by default use the DDR2 SPD
+EEPROM data to read what memory is installed.
+
+There is a hardware errata, which causes the older local bus SDRAM
+SPD EEPROM to land at the same address as the DDR2 SPD EEPROM, so
+that the SPD data can not be read reliably.
+
+If you want to upgrade to larger RAM size, you can simply enable
+ #define CONFIG_SPD_EEPROM
+ #define CONFIG_DDR_SPD
+in include/configs/sbc8548.h file. (The lines are already there
+but listed as #undef).
+
+Note that you will have to physically remove the LBC 128MB DIMM
+from the board's socket to resolve the above i2c address overlap
+issue and allow SPD autodetection of RAM to work.
+
Updating U-boot with U-boot:
============================
diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index 1df2225..44c7526 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -119,9 +119,15 @@
/* DDR Setup */
#define CONFIG_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+/*
+ * A hardware errata caused the LBC SDRAM SPD and the DDR2 SPD
+ * to collide, meaning you couldn't reliably read either. So
+ * physically remove the LBC PC100 SDRAM module from the board
+ * before enabling the two SPD options below.
+ */
#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#undef CONFIG_DDR_SPD
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
@@ -283,9 +289,14 @@
/*
* SDRAM on the Local Bus (CS3 and CS4)
+ * Note that most boards have a hardware errata where both the
+ * LBC SDRAM and the DDR2 SDRAM decode at 0x51, making it impossible
+ * to use CONFIG_DDR_SPD unless you physically remove the LBC DIMM.
*/
+#ifndef CONFIG_DDR_SPD
#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
#define CONFIG_SYS_LBC_SDRAM_SIZE 128 /* LBC SDRAM is 128MB */
+#endif
/*
* Base Register 3 and Option Register 3 configure the 1st 1/2 SDRAM.