path: root/drivers/usb/host/ehci-tegra.c

/*
 * Copyright (c) 2011 The Chromium OS Authors.
 * Copyright (c) 2009-2013 NVIDIA Corporation
 * Copyright (c) 2013 Lucas Stach
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <asm/errno.h>
#include <asm/io.h>
#include <asm-generic/gpio.h>
#include <asm/arch/clock.h>
#include <asm/arch-tegra/usb.h>
#include <asm/arch-tegra/clk_rst.h>
#include <usb.h>
#include <usb/ulpi.h>
#include <libfdt.h>
#include <fdtdec.h>

#include "ehci.h"

#define USB1_ADDR_MASK	0xFFFF0000

#define HOSTPC1_DEVLC	0x84
#define HOSTPC1_PSPD(x)		(((x) >> 25) & 0x3)

#ifdef CONFIG_USB_ULPI
	#ifndef CONFIG_USB_ULPI_VIEWPORT
	#error	"To use CONFIG_USB_ULPI on Tegra Boards you have to also \
		define CONFIG_USB_ULPI_VIEWPORT"
	#endif
#endif

enum {
	USB_PORTS_MAX	= 3,		/* Maximum ports we allow */
};

/* Parameters we need for USB */
enum {
	PARAM_DIVN,                     /* PLL FEEDBACK DIVIDer */
	PARAM_DIVM,                     /* PLL INPUT DIVIDER */
	PARAM_DIVP,                     /* POST DIVIDER (2^N) */
	PARAM_CPCON,                    /* BASE PLLC CHARGE Pump setup ctrl */
	PARAM_LFCON,                    /* BASE PLLC LOOP FILter setup ctrl */
	PARAM_ENABLE_DELAY_COUNT,       /* PLL-U Enable Delay Count */
	PARAM_STABLE_COUNT,             /* PLL-U STABLE count */
	PARAM_ACTIVE_DELAY_COUNT,       /* PLL-U Active delay count */
	PARAM_XTAL_FREQ_COUNT,          /* PLL-U XTAL frequency count */
	PARAM_DEBOUNCE_A_TIME,          /* 10MS DELAY for BIAS_DEBOUNCE_A */
	PARAM_BIAS_TIME,                /* 20US DELAY AFter bias cell op */

	PARAM_COUNT
};

/* Possible port types (dual role mode) */
enum dr_mode {
	DR_MODE_NONE = 0,
	DR_MODE_HOST,		/* supports host operation */
	DR_MODE_DEVICE,		/* supports device operation */
	DR_MODE_OTG,		/* supports both */
};

/* Information about a USB port */
struct fdt_usb {
	struct usb_ctlr *reg;	/* address of registers in physical memory */
	unsigned utmi:1;	/* 1 if port has external tranceiver, else 0 */
	unsigned ulpi:1;	/* 1 if port has external ULPI transceiver */
	unsigned enabled:1;	/* 1 to enable, 0 to disable */
	unsigned has_legacy_mode:1; /* 1 if this port has legacy mode */
	unsigned initialized:1; /* has this port already been initialized? */
	enum dr_mode dr_mode;	/* dual role mode */
	enum periph_id periph_id;/* peripheral id */
	struct fdt_gpio_state vbus_gpio;	/* GPIO for vbus enable */
	struct fdt_gpio_state phy_reset_gpio; /* GPIO to reset ULPI phy */
};

static struct fdt_usb port[USB_PORTS_MAX];	/* List of valid USB ports */
static unsigned port_count;			/* Number of available ports */
/* Port that needs to clear CSC after Port Reset */
static u32 port_addr_clear_csc;

/*
 * This table has USB timing parameters for each Oscillator frequency we
 * support. There are four sets of values:
 *
 * 1. PLLU configuration information (reference clock is osc/clk_m and
 * PLLU-FOs are fixed at 12MHz/60MHz/480MHz).
 *
 *  Reference frequency     13.0MHz      19.2MHz      12.0MHz      26.0MHz
 *  ----------------------------------------------------------------------
 *      DIVN                960 (0x3c0)  200 (0c8)    960 (3c0h)   960 (3c0)
 *      DIVM                13 (0d)      4 (04)       12 (0c)      26 (1a)
 * Filter frequency (MHz)   1            4.8          6            2
 * CPCON                    1100b        0011b        1100b        1100b
 * LFCON0                   0            0            0            0
 *
 * 2. PLL CONFIGURATION & PARAMETERS for different clock generators:
 *
 * Reference frequency     13.0MHz         19.2MHz         12.0MHz     26.0MHz
 * ---------------------------------------------------------------------------
 * PLLU_ENABLE_DLY_COUNT   02 (0x02)       03 (03)         02 (02)     04 (04)
 * PLLU_STABLE_COUNT       51 (33)         75 (4B)         47 (2F)    102 (66)
 * PLL_ACTIVE_DLY_COUNT    05 (05)         06 (06)         04 (04)     09 (09)
 * XTAL_FREQ_COUNT        127 (7F)        187 (BB)        118 (76)    254 (FE)
 *
 * 3. Debounce values IdDig, Avalid, Bvalid, VbusValid, VbusWakeUp, and
 * SessEnd. Each of these signals have their own debouncer and for each of
 * those one out of two debouncing times can be chosen (BIAS_DEBOUNCE_A or
 * BIAS_DEBOUNCE_B).
 *
 * The values of DEBOUNCE_A and DEBOUNCE_B are calculated as follows:
 *    0xffff -> No debouncing at all
 *    <n> ms = <n> *1000 / (1/19.2MHz) / 4
 *
 * So to program a 1 ms debounce for BIAS_DEBOUNCE_A, we have:
 * BIAS_DEBOUNCE_A[15:0] = 1000 * 19.2 / 4  = 4800 = 0x12c0
 *
 * We need to use only DebounceA for BOOTROM. We don't need the DebounceB
 * values, so we can keep those to default.
 *
 * 4. The 20 microsecond delay after bias cell operation.
 */
static const unsigned T20_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = {
	/* DivN, DivM, DivP, CPCON, LFCON, Delays             Debounce, Bias */
	{ 0x3C0, 0x0D, 0x00, 0xC,   0,  0x02, 0x33, 0x05, 0x7F, 0x7EF4, 5 },
	{ 0x0C8, 0x04, 0x00, 0x3,   0,  0x03, 0x4B, 0x06, 0xBB, 0xBB80, 7 },
	{ 0x3C0, 0x0C, 0x00, 0xC,   0,  0x02, 0x2F, 0x04, 0x76, 0x7530, 5 },
	{ 0x3C0, 0x1A, 0x00, 0xC,   0,  0x04, 0x66, 0x09, 0xFE, 0xFDE8, 9 }
};

static const unsigned T30_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = {
	/* DivN, DivM, DivP, CPCON, LFCON, Delays             Debounce, Bias */
	{ 0x3C0, 0x0D, 0x00, 0xC,   1,  0x02, 0x33, 0x09, 0x7F, 0x7EF4, 5 },
	{ 0x0C8, 0x04, 0x00, 0x3,   0,  0x03, 0x4B, 0x0C, 0xBB, 0xBB80, 7 },
	{ 0x3C0, 0x0C, 0x00, 0xC,   1,  0x02, 0x2F, 0x08, 0x76, 0x7530, 5 },
	{ 0x3C0, 0x1A, 0x00, 0xC,   1,  0x04, 0x66, 0x09, 0xFE, 0xFDE8, 9 }
};

static const unsigned T114_usb_pll[CLOCK_OSC_FREQ_COUNT][PARAM_COUNT] = {
	/* DivN, DivM, DivP, CPCON, LFCON, Delays             Debounce, Bias */
	{ 0x3C0, 0x0D, 0x00, 0xC,   2,  0x02, 0x33, 0x09, 0x7F, 0x7EF4, 6 },
	{ 0x0C8, 0x04, 0x00, 0x3,   2,  0x03, 0x4B, 0x0C, 0xBB, 0xBB80, 8 },
	{ 0x3C0, 0x0C, 0x00, 0xC,   2,  0x02, 0x2F, 0x08, 0x76, 0x7530, 5 },
	{ 0x3C0, 0x1A, 0x00, 0xC,   2,  0x04, 0x66, 0x09, 0xFE, 0xFDE8, 0xB }
};

/* UTMIP Idle Wait Delay */
static const u8 utmip_idle_wait_delay = 17;

/* UTMIP Elastic limit */
static const u8 utmip_elastic_limit = 16;

/* UTMIP High Speed Sync Start Delay */
static const u8 utmip_hs_sync_start_delay = 9;

struct fdt_usb_controller {
	int compat;
	/* flag to determine whether controller supports hostpc register */
	u32 has_hostpc:1;
	const unsigned *pll_parameter;
};

static struct fdt_usb_controller fdt_usb_controllers[] = {
	{
		.compat		= COMPAT_NVIDIA_TEGRA20_USB,
		.has_hostpc	= 0,
		.pll_parameter	= (const unsigned *)T20_usb_pll,
	},
	{
		.compat		= COMPAT_NVIDIA_TEGRA30_USB,
		.has_hostpc	= 1,
		.pll_parameter	= (const unsigned *)T30_usb_pll,
	},
	{
		.compat		= COMPAT_NVIDIA_TEGRA114_USB,
		.has_hostpc	= 1,
		.pll_parameter	= (const unsigned *)T114_usb_pll,
	},
};

static struct fdt_usb_controller *controller;

/*
 * A known hardware issue where Connect Status Change bit of PORTSC register
 * of USB1 controller will be set after Port Reset.
 * We have to clear it in order for later device enumeration to proceed.
 * This ehci_powerup_fixup overrides the weak function ehci_powerup_fixup
 * in "ehci-hcd.c".
 */
void ehci_powerup_fixup(uint32_t *status_reg, uint32_t *reg)
{
	mdelay(50);
	/* This is to avoid PORT_ENABLE bit to be cleared in "ehci-hcd.c". */
	if (controller->has_hostpc)
		*reg |= EHCI_PS_PE;

	if (((u32)status_reg & TEGRA_USB_ADDR_MASK) != port_addr_clear_csc)
		return;
	/* For EHCI_PS_CSC to be cleared in ehci_hcd.c */
	if (ehci_readl(status_reg) & EHCI_PS_CSC)
		*reg |= EHCI_PS_CSC;
}

/*
 * This ehci_set_usbmode overrides the weak function ehci_set_usbmode
 * in "ehci-hcd.c".
 */
void ehci_set_usbmode(int index)
{
	struct fdt_usb *config;
	struct usb_ctlr *usbctlr;
	uint32_t tmp;

	config = &port[index];
	usbctlr = config->reg;

	tmp = ehci_readl(&usbctlr->usb_mode);
	tmp |= USBMODE_CM_HC;
	ehci_writel(&usbctlr->usb_mode, tmp);
}

/*
 * This ehci_get_port_speed overrides the weak function ehci_get_port_speed
 * in "ehci-hcd.c".
 */
int ehci_get_port_speed(struct ehci_hcor *hcor, uint32_t reg)
{
	uint32_t tmp;
	uint32_t *reg_ptr;

	if (controller->has_hostpc) {
		reg_ptr = (uint32_t *)((u8 *)&hcor->or_usbcmd + HOSTPC1_DEVLC);
		tmp = ehci_readl(reg_ptr);
		return HOSTPC1_PSPD(tmp);
	} else
		return PORTSC_PSPD(reg);
}

/* Put the port into host mode */
static void set_host_mode(struct fdt_usb *config)
{
	/*
	 * If we are an OTG port, check if remote host is driving VBus and
	 * bail out in this case.
	 */
	if (config->dr_mode == DR_MODE_OTG &&
		(readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS))
		return;

	/*
	 * If not driving, we set the GPIO to enable VBUS. We assume
	 * that the pinmux is set up correctly for this.
	 */
	if (fdt_gpio_isvalid(&config->vbus_gpio)) {
		fdtdec_setup_gpio(&config->vbus_gpio);
		gpio_direction_output(config->vbus_gpio.gpio,
			(config->vbus_gpio.flags & FDT_GPIO_ACTIVE_LOW) ?
				 0 : 1);
		debug("set_host_mode: GPIO %d %s\n", config->vbus_gpio.gpio,
			(config->vbus_gpio.flags & FDT_GPIO_ACTIVE_LOW) ?
				"low" : "high");
	}
}

void usbf_reset_controller(struct fdt_usb *config, struct usb_ctlr *usbctlr)
{
	/* Reset the USB controller with 2us delay */
	reset_periph(config->periph_id, 2);

	/*
	 * Set USB1_NO_LEGACY_MODE to 1, Registers are accessible under
	 * base address
	 */
	if (config->has_legacy_mode)
		setbits_le32(&usbctlr->usb1_legacy_ctrl, USB1_NO_LEGACY_MODE);

	/* Put UTMIP1/3 in reset */
	setbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET);

	/* Enable the UTMIP PHY */
	if (config->utmi)
		setbits_le32(&usbctlr->susp_ctrl, UTMIP_PHY_ENB);
}

static const unsigned *get_pll_timing(void)
{
	const unsigned *timing;

	timing = controller->pll_parameter +
		clock_get_osc_freq() * PARAM_COUNT;

	return timing;
}

/* set up the UTMI USB controller with the parameters provided */
static int init_utmi_usb_controller(struct fdt_usb *config)
{
	u32 val;
	int loop_count;
	const unsigned *timing;
	struct usb_ctlr *usbctlr = config->reg;
	struct clk_rst_ctlr *clkrst;
	struct usb_ctlr *usb1ctlr;

	clock_enable(config->periph_id);

	/* Reset the usb controller */
	usbf_reset_controller(config, usbctlr);

	/* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */
	clrbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);

	/* Follow the crystal clock disable by >100ns delay */
	udelay(1);

	/*
	 * To Use the A Session Valid for cable detection logic, VBUS_WAKEUP
	 * mux must be switched to actually use a_sess_vld threshold.
	 */
	if (config->dr_mode == DR_MODE_OTG &&
	    fdt_gpio_isvalid(&config->vbus_gpio))
		clrsetbits_le32(&usbctlr->usb1_legacy_ctrl,
			VBUS_SENSE_CTL_MASK,
			VBUS_SENSE_CTL_A_SESS_VLD << VBUS_SENSE_CTL_SHIFT);

	/*
	 * PLL Delay CONFIGURATION settings. The following parameters control
	 * the bring up of the plls.
	 */
	timing = get_pll_timing();

	if (!controller->has_hostpc) {
		val = readl(&usbctlr->utmip_misc_cfg1);
		clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
				timing[PARAM_STABLE_COUNT] <<
				UTMIP_PLLU_STABLE_COUNT_SHIFT);
		clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
				timing[PARAM_ACTIVE_DELAY_COUNT] <<
				UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
		writel(val, &usbctlr->utmip_misc_cfg1);

		/* Set PLL enable delay count and crystal frequency count */
		val = readl(&usbctlr->utmip_pll_cfg1);
		clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
				timing[PARAM_ENABLE_DELAY_COUNT] <<
				UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
		clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
				timing[PARAM_XTAL_FREQ_COUNT] <<
				UTMIP_XTAL_FREQ_COUNT_SHIFT);
		writel(val, &usbctlr->utmip_pll_cfg1);
	} else {
		clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;

		val = readl(&clkrst->crc_utmip_pll_cfg2);
		clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
				timing[PARAM_STABLE_COUNT] <<
				UTMIP_PLLU_STABLE_COUNT_SHIFT);
		clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
				timing[PARAM_ACTIVE_DELAY_COUNT] <<
				UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
		writel(val, &clkrst->crc_utmip_pll_cfg2);

		/* Set PLL enable delay count and crystal frequency count */
		val = readl(&clkrst->crc_utmip_pll_cfg1);
		clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
				timing[PARAM_ENABLE_DELAY_COUNT] <<
				UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
		clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
				timing[PARAM_XTAL_FREQ_COUNT] <<
				UTMIP_XTAL_FREQ_COUNT_SHIFT);
		writel(val, &clkrst->crc_utmip_pll_cfg1);

		/* Disable Power Down state for PLL */
		clrbits_le32(&clkrst->crc_utmip_pll_cfg1,
			     PLLU_POWERDOWN | PLL_ENABLE_POWERDOWN |
			     PLL_ACTIVE_POWERDOWN);

		/* Recommended PHY settings for EYE diagram */
		val = readl(&usbctlr->utmip_xcvr_cfg0);
		clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MASK,
				0x4 << UTMIP_XCVR_SETUP_SHIFT);
		clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MSB_MASK,
				0x3 << UTMIP_XCVR_SETUP_MSB_SHIFT);
		clrsetbits_le32(&val, UTMIP_XCVR_HSSLEW_MSB_MASK,
				0x8 << UTMIP_XCVR_HSSLEW_MSB_SHIFT);
		writel(val, &usbctlr->utmip_xcvr_cfg0);
		clrsetbits_le32(&usbctlr->utmip_xcvr_cfg1,
				UTMIP_XCVR_TERM_RANGE_ADJ_MASK,
				0x7 << UTMIP_XCVR_TERM_RANGE_ADJ_SHIFT);

		/* Some registers can be controlled from USB1 only. */
		if (config->periph_id != PERIPH_ID_USBD) {
			clock_enable(PERIPH_ID_USBD);
			/* Disable Reset if in Reset state */
			reset_set_enable(PERIPH_ID_USBD, 0);
		}
		usb1ctlr = (struct usb_ctlr *)
			((u32)config->reg & USB1_ADDR_MASK);
		val = readl(&usb1ctlr->utmip_bias_cfg0);
		setbits_le32(&val, UTMIP_HSDISCON_LEVEL_MSB);
		clrsetbits_le32(&val, UTMIP_HSDISCON_LEVEL_MASK,
				0x1 << UTMIP_HSDISCON_LEVEL_SHIFT);
		clrsetbits_le32(&val, UTMIP_HSSQUELCH_LEVEL_MASK,
				0x2 << UTMIP_HSSQUELCH_LEVEL_SHIFT);
		writel(val, &usb1ctlr->utmip_bias_cfg0);

		/* Miscellaneous setting mentioned in Programming Guide */
		clrbits_le32(&usbctlr->utmip_misc_cfg0,
			     UTMIP_SUSPEND_EXIT_ON_EDGE);
	}

	/* Setting the tracking length time */
	clrsetbits_le32(&usbctlr->utmip_bias_cfg1,
		UTMIP_BIAS_PDTRK_COUNT_MASK,
		timing[PARAM_BIAS_TIME] << UTMIP_BIAS_PDTRK_COUNT_SHIFT);

	/* Program debounce time for VBUS to become valid */
	clrsetbits_le32(&usbctlr->utmip_debounce_cfg0,
		UTMIP_DEBOUNCE_CFG0_MASK,
		timing[PARAM_DEBOUNCE_A_TIME] << UTMIP_DEBOUNCE_CFG0_SHIFT);

	setbits_le32(&usbctlr->utmip_tx_cfg0, UTMIP_FS_PREAMBLE_J);

	/* Disable battery charge enabling bit */
	setbits_le32(&usbctlr->utmip_bat_chrg_cfg0, UTMIP_PD_CHRG);

	clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_XCVR_LSBIAS_SE);
	setbits_le32(&usbctlr->utmip_spare_cfg0, FUSE_SETUP_SEL);

	/*
	 * Configure the UTMIP_IDLE_WAIT and UTMIP_ELASTIC_LIMIT
	 * Setting these fields, together with default values of the
	 * other fields, results in programming the registers below as
	 * follows:
	 *         UTMIP_HSRX_CFG0 = 0x9168c000
	 *         UTMIP_HSRX_CFG1 = 0x13
	 */

	/* Set PLL enable delay count and Crystal frequency count */
	val = readl(&usbctlr->utmip_hsrx_cfg0);
	clrsetbits_le32(&val, UTMIP_IDLE_WAIT_MASK,
		utmip_idle_wait_delay << UTMIP_IDLE_WAIT_SHIFT);
	clrsetbits_le32(&val, UTMIP_ELASTIC_LIMIT_MASK,
		utmip_elastic_limit << UTMIP_ELASTIC_LIMIT_SHIFT);
	writel(val, &usbctlr->utmip_hsrx_cfg0);

	/* Configure the UTMIP_HS_SYNC_START_DLY */
	clrsetbits_le32(&usbctlr->utmip_hsrx_cfg1,
		UTMIP_HS_SYNC_START_DLY_MASK,
		utmip_hs_sync_start_delay << UTMIP_HS_SYNC_START_DLY_SHIFT);

	/* Preceed the crystal clock disable by >100ns delay. */
	udelay(1);

	/* Resuscitate crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN */
	setbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);

	if (controller->has_hostpc) {
		if (config->periph_id == PERIPH_ID_USBD)
			clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
				     UTMIP_FORCE_PD_SAMP_A_POWERDOWN);
		if (config->periph_id == PERIPH_ID_USB2)
			clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
				     UTMIP_FORCE_PD_SAMP_B_POWERDOWN);
		if (config->periph_id == PERIPH_ID_USB3)
			clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
				     UTMIP_FORCE_PD_SAMP_C_POWERDOWN);
	}
	/* Finished the per-controller init. */

	/* De-assert UTMIP_RESET to bring out of reset. */
	clrbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET);

	/* Wait for the phy clock to become valid in 100 ms */
	for (loop_count = 100000; loop_count != 0; loop_count--) {
		if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID)
			break;
		udelay(1);
	}
	if (!loop_count)
		return -1;

	/* Disable ICUSB FS/LS transceiver */
	clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1);

	/* Select UTMI parallel interface */
#if defined(CONFIG_TEGRA20)
	if (config->periph_id == PERIPH_ID_USBD) {
		clrsetbits_le32(&usbctlr->port_sc1, PTS1_MASK,
				PTS_UTMI << PTS1_SHIFT);
		clrbits_le32(&usbctlr->port_sc1, STS1);
	} else {
		clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
				PTS_UTMI << PTS_SHIFT);
		clrbits_le32(&usbctlr->port_sc1, STS);
	}
#else
	/* Set to Host mode after Controller Reset was done */
	clrsetbits_le32(&usbctlr->usb_mode, USBMODE_CM_HC,
			USBMODE_CM_HC);
	/* Select PHY interface after setting host mode */
	clrsetbits_le32(&usbctlr->hostpc1_devlc, PTS_MASK,
			PTS_UTMI << PTS_SHIFT);
	clrbits_le32(&usbctlr->hostpc1_devlc, STS);
#endif

	/* Deassert power down state */
	clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN |
		UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN);
	clrbits_le32(&usbctlr->utmip_xcvr_cfg1, UTMIP_FORCE_PDDISC_POWERDOWN |
		UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN);

	if (controller->has_hostpc) {
		/*
		 * BIAS Pad Power Down is common among all 3 USB
		 * controllers and can be controlled from USB1 only.
		 */
		usb1ctlr = (struct usb_ctlr *)
			((u32)config->reg & USB1_ADDR_MASK);
		clrbits_le32(&usb1ctlr->utmip_bias_cfg0, UTMIP_BIASPD);
		udelay(25);
		clrbits_le32(&usb1ctlr->utmip_bias_cfg1,
			     UTMIP_FORCE_PDTRK_POWERDOWN);
	}
	return 0;
}

#ifdef CONFIG_USB_ULPI
/* if board file does not set a ULPI reference frequency we default to 24MHz */
#ifndef CONFIG_ULPI_REF_CLK
#define CONFIG_ULPI_REF_CLK 24000000
#endif

/* set up the ULPI USB controller with the parameters provided */
static int init_ulpi_usb_controller(struct fdt_usb *config)
{
	u32 val;
	int loop_count;
	struct ulpi_viewport ulpi_vp;
	struct usb_ctlr *usbctlr = config->reg;

	/* set up ULPI reference clock on pllp_out4 */
	clock_enable(PERIPH_ID_DEV2_OUT);
	clock_set_pllout(CLOCK_ID_PERIPH, PLL_OUT4, CONFIG_ULPI_REF_CLK);

	/* reset ULPI phy */
	if (fdt_gpio_isvalid(&config->phy_reset_gpio)) {
		fdtdec_setup_gpio(&config->phy_reset_gpio);
		gpio_direction_output(config->phy_reset_gpio.gpio, 0);
		mdelay(5);
		gpio_set_value(config->phy_reset_gpio.gpio, 1);
	}

	/* Reset the usb controller */
	clock_enable(config->periph_id);
	usbf_reset_controller(config, usbctlr);

	/* enable pinmux bypass */
	setbits_le32(&usbctlr->ulpi_timing_ctrl_0,
			ULPI_CLKOUT_PINMUX_BYP | ULPI_OUTPUT_PINMUX_BYP);

	/* Select ULPI parallel interface */
#if defined(CONFIG_TEGRA20)
	clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
			PTS_ULPI << PTS_SHIFT);
#else
	/* Set to Host mode after Controller Reset was done */
	clrsetbits_le32(&usbctlr->usb_mode, USBMODE_CM_HC,
			USBMODE_CM_HC);
	/* Select PHY interface after setting host mode */
	clrsetbits_le32(&usbctlr->hostpc1_devlc, PTS_MASK,
			PTS_ULPI << PTS_SHIFT);
#endif

	/* enable ULPI transceiver */
	setbits_le32(&usbctlr->susp_ctrl, ULPI_PHY_ENB);

	/* configure ULPI transceiver timings */
	val = 0;
	writel(val, &usbctlr->ulpi_timing_ctrl_1);

	val |= ULPI_DATA_TRIMMER_SEL(4);
	val |= ULPI_STPDIRNXT_TRIMMER_SEL(4);
	val |= ULPI_DIR_TRIMMER_SEL(4);
	writel(val, &usbctlr->ulpi_timing_ctrl_1);
	udelay(10);

	val |= ULPI_DATA_TRIMMER_LOAD;
	val |= ULPI_STPDIRNXT_TRIMMER_LOAD;
	val |= ULPI_DIR_TRIMMER_LOAD;
	writel(val, &usbctlr->ulpi_timing_ctrl_1);

	/* set up phy for host operation with external vbus supply */
	ulpi_vp.port_num = 0;
	ulpi_vp.viewport_addr = (u32)&usbctlr->ulpi_viewport;

	if (ulpi_init(&ulpi_vp)) {
		printf("Tegra ULPI viewport init failed\n");
		return -1;
	}

	ulpi_set_vbus(&ulpi_vp, 1, 1);
	ulpi_set_vbus_indicator(&ulpi_vp, 1, 1, 0);

	/* enable wakeup events */
	setbits_le32(&usbctlr->port_sc1, WKCN | WKDS | WKOC);

	/* Enable and wait for the phy clock to become valid in 100 ms */
	setbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR);
	for (loop_count = 100000; loop_count != 0; loop_count--) {
		if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID)
			break;
		udelay(1);
	}
	if (!loop_count)
		return -1;
	clrbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR);

	return 0;
}
#else
static int init_ulpi_usb_controller(struct fdt_usb *config)
{
	printf("No code to set up ULPI controller, please enable"
			"CONFIG_USB_ULPI and CONFIG_USB_ULPI_VIEWPORT");
	return -1;
}
#endif

static void config_clock(const u32 timing[])
{
	clock_start_pll(CLOCK_ID_USB,
		timing[PARAM_DIVM], timing[PARAM_DIVN], timing[PARAM_DIVP],
		timing[PARAM_CPCON], timing[PARAM_LFCON]);
}

static int fdt_decode_usb(const void *blob, int node, struct fdt_usb *config)
{
	const char *phy, *mode;

	config->reg = (struct usb_ctlr *)fdtdec_get_addr(blob, node, "reg");
	mode = fdt_getprop(blob, node, "dr_mode", NULL);
	if (mode) {
		if (0 == strcmp(mode, "host"))
			config->dr_mode = DR_MODE_HOST;
		else if (0 == strcmp(mode, "peripheral"))
			config->dr_mode = DR_MODE_DEVICE;
		else if (0 == strcmp(mode, "otg"))
			config->dr_mode = DR_MODE_OTG;
		else {
			debug("%s: Cannot decode dr_mode '%s'\n", __func__,
			      mode);
			return -FDT_ERR_NOTFOUND;
		}
	} else {
		config->dr_mode = DR_MODE_HOST;
	}

	phy = fdt_getprop(blob, node, "phy_type", NULL);
	config->utmi = phy && 0 == strcmp("utmi", phy);
	config->ulpi = phy && 0 == strcmp("ulpi", phy);
	config->enabled = fdtdec_get_is_enabled(blob, node);
	config->has_legacy_mode = fdtdec_get_bool(blob, node,
						  "nvidia,has-legacy-mode");
	if (config->has_legacy_mode)
		port_addr_clear_csc = (u32) config->reg;
	config->periph_id = clock_decode_periph_id(blob, node);
	if (config->periph_id == PERIPH_ID_NONE) {
		debug("%s: Missing/invalid peripheral ID\n", __func__);
		return -FDT_ERR_NOTFOUND;
	}
	fdtdec_decode_gpio(blob, node, "nvidia,vbus-gpio", &config->vbus_gpio);
	fdtdec_decode_gpio(blob, node, "nvidia,phy-reset-gpio",
			&config->phy_reset_gpio);
	debug("enabled=%d, legacy_mode=%d, utmi=%d, ulpi=%d, periph_id=%d, "
		"vbus=%d, phy_reset=%d, dr_mode=%d\n",
		config->enabled, config->has_legacy_mode, config->utmi,
		config->ulpi, config->periph_id, config->vbus_gpio.gpio,
		config->phy_reset_gpio.gpio, config->dr_mode);

	return 0;
}

/*
 * process_usb_nodes() - Process a list of USB nodes, adding them to our list
 *			of USB ports.
 * @blob:	fdt blob
 * @node_list:	list of nodes to process (any <=0 are ignored)
 * @count:	number of nodes to process
 *
 * Return:	0 - ok, -1 - error
 */
static int process_usb_nodes(const void *blob, int node_list[], int count)
{
	struct fdt_usb config;
	int node, i;
	int clk_done = 0;

	port_count = 0;
	for (i = 0; i < count; i++) {
		if (port_count == USB_PORTS_MAX) {
			printf("tegrausb: Cannot register more than %d ports\n",
				USB_PORTS_MAX);
			return -1;
		}

		debug("USB %d: ", i);
		node = node_list[i];
		if (!node)
			continue;
		if (fdt_decode_usb(blob, node, &config)) {
			debug("Cannot decode USB node %s\n",
			      fdt_get_name(blob, node, NULL));
			return -1;
		}
		if (!clk_done) {
			config_clock(get_pll_timing());
			clk_done = 1;
		}
		config.initialized = 0;

		/* add new USB port to the list of available ports */
		port[port_count++] = config;
	}

	return 0;
}

int usb_process_devicetree(const void *blob)
{
	int node_list[USB_PORTS_MAX];
	int count, err = 0;
	int i;

	for (i = 0; i < ARRAY_SIZE(fdt_usb_controllers); i++) {
		controller = &fdt_usb_controllers[i];

		count = fdtdec_find_aliases_for_id(blob, "usb",
			controller->compat, node_list, USB_PORTS_MAX);
		if (count) {
			err = process_usb_nodes(blob, node_list, count);
			if (err)
				printf("%s: Error processing USB node!\n",
				       __func__);
			return err;
		}
	}
	if (i == ARRAY_SIZE(fdt_usb_controllers))
		controller = NULL;

	return err;
}

/**
 * Start up the given port number (ports are numbered from 0 on each board).
 * This returns values for the appropriate hccr and hcor addresses to use for
 * USB EHCI operations.
 *
 * @param index	port number to start
 * @param hccr		returns start address of EHCI HCCR registers
 * @param hcor		returns start address of EHCI HCOR registers
 * @return 0 if ok, -1 on error (generally invalid port number)
 */
int ehci_hcd_init(int index, enum usb_init_type init,
		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
	struct fdt_usb *config;
	struct usb_ctlr *usbctlr;

	if (index >= port_count)
		return -1;

	config = &port[index];

	/* skip init, if the port is already initialized */
	if (config->initialized)
		goto success;

	if (config->utmi && init_utmi_usb_controller(config)) {
		printf("tegrausb: Cannot init port %d\n", index);
		return -1;
	}

	if (config->ulpi && init_ulpi_usb_controller(config)) {
		printf("tegrausb: Cannot init port %d\n", index);
		return -1;
	}

	set_host_mode(config);

	config->initialized = 1;

success:
	usbctlr = config->reg;
	*hccr = (struct ehci_hccr *)&usbctlr->cap_length;
	*hcor = (struct ehci_hcor *)&usbctlr->usb_cmd;

	return 0;
}

/*
 * Bring down the specified USB controller
 */
int ehci_hcd_stop(int index)
{
	struct usb_ctlr *usbctlr;

	usbctlr = port[index].reg;

	/* Stop controller */
	writel(0, &usbctlr->usb_cmd);
	udelay(1000);

	/* Initiate controller reset */
	writel(2, &usbctlr->usb_cmd);
	udelay(1000);

	port[index].initialized = 0;

	return 0;
}