summaryrefslogtreecommitdiff
path: root/drivers/ddr/mvebu/ddr3_axp_config.h
blob: 800d2d14765db396c547cc76b2bc196dfd0bb820 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
/*
 * Copyright (C) Marvell International Ltd. and its affiliates
 *
 * SPDX-License-Identifier:	GPL-2.0
 */

#ifndef __DDR3_AXP_CONFIG_H
#define __DDR3_AXP_CONFIG_H

/*
 * DDR3_LOG_LEVEL Information
 *
 * Level 0: Provides an error code in a case of failure, RL, WL errors
 *          and other algorithm failure
 * Level 1: Provides the D-Unit setup (SPD/Static configuration)
 * Level 2: Provides the windows margin as a results of DQS centeralization
 * Level 3: Provides the windows margin of each DQ as a results of DQS
 *          centeralization
 */
#ifdef CONFIG_DDR_LOG_LEVEL
#define	DDR3_LOG_LEVEL	CONFIG_DDR_LOG_LEVEL
#else
#define	DDR3_LOG_LEVEL	0
#endif

#define DDR3_PBS        1

/* This flag allows the execution of SW WL/RL upon HW failure */
#define DDR3_RUN_SW_WHEN_HW_FAIL    1

/*
 * General Configurations
 *
 * The following parameters are required for proper setup:
 *
 * DDR_TARGET_FABRIC   - Set desired fabric configuration
 *                       (for sample@Reset fabfreq parameter)
 * DRAM_ECC            - Set ECC support 1/0
 * BUS_WIDTH           - 64/32 bit
 * CONFIG_SPD_EEPROM   - Enables auto detection of DIMMs and their timing values
 * DQS_CLK_ALIGNED     - Set this if CLK and DQS signals are aligned on board
 * MIXED_DIMM_STATIC   - Mixed DIMM + On board devices support (ODT registers
 *                       values are taken statically)
 * DDR3_TRAINING_DEBUG - Debug prints of internal code
 */
#define DDR_TARGET_FABRIC			5
#define DRAM_ECC				0

#ifdef MV_DDR_32BIT
#define BUS_WIDTH                               32
#else
#define BUS_WIDTH				64
#endif

#undef DQS_CLK_ALIGNED
#undef MIXED_DIMM_STATIC
#define DDR3_TRAINING_DEBUG			0
#define REG_DIMM_SKIP_WL			0

/* Marvell boards specific configurations */
#if defined(DB_78X60_PCAC)
#undef CONFIG_SPD_EEPROM
#define STATIC_TRAINING
#endif

#if defined(DB_78X60_AMC)
#undef CONFIG_SPD_EEPROM
#undef  DRAM_ECC
#define DRAM_ECC				1
#endif

#ifdef CONFIG_SPD_EEPROM
/*
 * DIMM support parameters:
 * DRAM_2T - Set Desired 2T Mode - 0 - 1T, 0x1 - 2T, 0x2 - 3T
 * DIMM_CS_BITMAP - bitmap representing the optional CS in DIMMs
 * (0xF=CS0+CS1+CS2+CS3, 0xC=CS2+CS3...)
 */
#define DRAM_2T					0x0
#define DIMM_CS_BITMAP				0xF
#define DUNIT_SPD
#endif

#ifdef DRAM_ECC
/*
 * ECC support parameters:
 *
 * U_BOOT_START_ADDR, U_BOOT_SCRUB_SIZE - relevant when using ECC and need
 * to configure the scrubbing area
 */
#define TRAINING_SIZE				0x20000
#define U_BOOT_START_ADDR			0
#define U_BOOT_SCRUB_SIZE			0x1000000 /* TRAINING_SIZE */
#endif

/*
 * Registered DIMM Support - In case registered DIMM is attached,
 * please supply the following values:
 * (see JEDEC - JESD82-29A "Definition of the SSTE32882 Registering Clock
 * Driver with Parity and Quad Chip
 * Selects for DDR3/DDR3L/DDR3U RDIMM 1.5 V/1.35 V/1.25 V Applications")
 * RC0: Global Features Control Word
 * RC1: Clock Driver Enable Control Word
 * RC2: Timing Control Word
 * RC3-RC5 - taken from SPD
 * RC8: Additional IBT Setting Control Word
 * RC9: Power Saving Settings Control Word
 * RC10: Encoding for RDIMM Operating Speed
 * RC11: Operating Voltage VDD and VREFCA Control Word
 */
#define RDIMM_RC0				0
#define RDIMM_RC1				0
#define RDIMM_RC2				0
#define RDIMM_RC8				0
#define RDIMM_RC9				0
#define RDIMM_RC10				0x2
#define RDIMM_RC11				0x0

#if defined(MIXED_DIMM_STATIC) || !defined(CONFIG_SPD_EEPROM)
#define DUNIT_STATIC
#endif

#if defined(MIXED_DIMM_STATIC) || defined(CONFIG_SPD_EEPROM)
/*
 * This flag allows the user to change the dram refresh cycle in ps,
 * only in case of SPD or MIX DIMM topology
 */
#define TREFI_USER_EN

#ifdef TREFI_USER_EN
#define TREFI_USER				3900000
#endif
#endif

#ifdef CONFIG_SPD_EEPROM
/*
 * AUTO_DETECTION_SUPPORT - relevant ONLY for Marvell DB boards.
 * Enables I2C auto detection different options
 */
#if defined(CONFIG_DB_88F78X60) || defined(CONFIG_DB_88F78X60_REV2) || \
    defined(CONFIG_DB_784MP_GP)
#define AUTO_DETECTION_SUPPORT
#endif
#endif

#endif /* __DDR3_AXP_CONFIG_H */