summaryrefslogtreecommitdiff
path: root/doc/README.uniphier
blob: c270ecb9a5bb302d470331cc43ae1b09c08593da (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
U-Boot for UniPhier SoC family
==============================


Tested toolchains
-----------------

 (a) Ubuntu packages  (CROSS_COMPILE=arm-linux-gnueabi-)

  If you are building U-Boot on Ubuntu, its standard package is recommended.
  You can install it as follows:

    $ sudo apt-get install gcc-arm-linux-gnueabi-

 (b) Linaro compilers  (CROSS_COMPILE=arm-linux-gnueabihf-)

  You can download pre-built toolchains from:

    http://www.linaro.org/downloads/

 (c) kernel.org compilers  (CROSS_COMPILE=arm-unknown-linux-gnueabi-)

  You can download pre-built toolchains from:

    ftp://www.kernel.org/pub/tools/crosstool/files/bin/


Compile the source
------------------

PH1-sLD3 reference board:
    $ make uniphier_sld3_defconfig
    $ make CROSS_COMPILE=arm-linux-gnueabi-

PH1-LD4 reference board:
    $ make uniphier_ld4_sld8_defconfig
    $ make CROSS_COMPILE=arm-linux-gnueabi-

PH1-sLD8 reference board:
    $ make uniphier_ld4_sld8_defconfig
    $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-sld8-ref

PH1-Pro4 reference board:
    $ make uniphier_pro4_defconfig
    $ make CROSS_COMPILE=arm-linux-gnueabi-

PH1-Pro5 4KBOX Board:
    $ make uniphier_pro5_defconfig
    $ make CROSS_COMPILE=arm-linux-gnueabi-

ProXstream2 Gentil board:
    $ make uniphier_pxs2_ld6b_defconfig
    $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-proxstream2-gentil

ProXstream2 Vodka board:
    $ make uniphier_pxs2_ld6b_defconfig
    $ make CROSS_COMPILE=arm-linux-gnueabi-

PH1-LD6b reference board:
    $ make uniphier_pxs2_ld6b_defconfig
    $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-ld6b-ref

You may wish to change the "CROSS_COMPILE=arm-linux-gnueabi-"
to use your favorite compiler.


Burn U-Boot images to NAND
--------------------------

Write two files to the NAND device as follows:
 - spl/u-boot-spl.bin at the offset address 0x00000000
 - u-boot.img         at the offset address 0x00010000

If a TFTP server is available, the images can be easily updated.
Just copy the u-boot-spl-dtb.bin and u-boot-dtb.img to the TFTP public
directory, and then run the following command at the U-Boot command line:

  => run nandupdate


UniPhier specific commands
--------------------------

 - pinmon (enabled by CONFIG_CMD_PINMON)
     shows the boot mode pins that has been latched at the power-on reset

 - ddrphy (enabled by CONFIG_CMD_DDRPHY_DUMP)
     shows the DDR PHY parameters set by the PHY training


Supported devices
-----------------

 - UART (on-chip)
 - NAND
 - SD/eMMC
 - USB 2.0 (EHCI)
 - USB 3.0 (xHCI)
 - GPIO
 - LAN (on-board SMSC9118)
 - I2C
 - EEPROM (connected to the on-board I2C bus)
 - Support card (SRAM, NOR flash, some peripherals)


Micro Support Card
------------------

The recommended bit switch settings are as follows:

 SW2    OFF(1)/ON(0)   Description
 ------------------------------------------
 bit 1   <----         BKSZ[0]
 bit 2   ---->         BKSZ[1]
 bit 3   <----         SoC Bus Width 16/32
 bit 4   <----         SERIAL_SEL[0]
 bit 5   ---->         SERIAL_SEL[1]
 bit 6   ---->         BOOTSWAP_EN
 bit 7   <----         CS1/CS5
 bit 8   <----         SOC_SERIAL_DISABLE

 SW8    OFF(1)/ON(0)   Description
 ------------------------------------------
 bit 1    <----        CS1_SPLIT
 bit 2    <----        CASE9_ON
 bit 3    <----        CASE10_ON
 bit 4  Don't Care     Reserve
 bit 5  Don't Care     Reserve
 bit 6  Don't Care     Reserve
 bit 7    ---->        BURST_EN
 bit 8    ---->        FLASHBUS32_16

The BKSZ[1:0] specifies the address range of memory slot and peripherals
as follows:

 BKSZ    Description              RAM slot            Peripherals
 --------------------------------------------------------------------
 0b00   15MB RAM / 1MB Peri    00000000-00efffff    00f00000-00ffffff
 0b01   31MB RAM / 1MB Peri    00000000-01efffff    01f00000-01ffffff
 0b10   64MB RAM / 1MB Peri    00000000-03efffff    03f00000-03ffffff
 0b11  127MB RAM / 1MB Peri    00000000-07efffff    07f00000-07ffffff

Set BSKZ[1:0] to 0b01 for U-Boot.
This mode is the most handy because EA[24] is always supported by the save pin
mode of the system bus.  On the other hand, EA[25] is not supported for some
newer SoCs.  Even if it is, EA[25] is not connected on most of the boards.

--
Masahiro Yamada <yamada.masahiro@socionext.com>
Feb. 2016