1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
|
/*
* Copyright 2009 Extreme Engineering Solutions, Inc.
* Copyright 2007-2008 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <i2c.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
static void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
{
i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
sizeof(ddr2_spd_eeprom_t));
}
void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
unsigned int ctrl_num)
{
unsigned int i;
unsigned int i2c_address = 0;
for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
if (ctrl_num == 0) {
i2c_address = SPD_EEPROM_ADDRESS1;
#ifdef SPD_EEPROM_ADDRESS2
} else if (ctrl_num == 1) {
i2c_address = SPD_EEPROM_ADDRESS2;
#endif
} else {
/* An inalid ctrl number was give, use default SPD */
printf("ERROR: invalid DDR ctrl: %d\n", ctrl_num);
i2c_address = SPD_EEPROM_ADDRESS1;
}
get_spd(&(ctrl_dimms_spd[i]), i2c_address);
}
}
/*
* There are four board-specific SDRAM timing parameters which must be
* calculated based on the particular PCB artwork. These are:
* 1.) CPO (Read Capture Delay)
* - TIMING_CFG_2 register
* Source: Calculation based on board trace lengths and
* chip-specific internal delays.
* 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay)
* - TIMING_CFG_2 register
* Source: Calculation based on board trace lengths.
* Unless clock and DQ lanes are very different
* lengths (>2"), this should be set to the nominal value
* of 1/2 clock delay.
* 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
* - DDR_SDRAM_CLK_CNTL register
* Source: Signal Integrity Simulations
* 4.) 2T Timing on Addr/Ctl
* - TIMING_CFG_2 register
* Source: Signal Integrity Simulations
* Usually only needed with heavy load/very high speed (>DDR2-800)
*
* PCB routing on the XPedite5170 is nearly identical to the XPedite5370
* so we use the XPedite5370 settings as a basis for the XPedite5170.
*/
typedef struct board_memctl_options {
uint16_t datarate_mhz_low;
uint16_t datarate_mhz_high;
uint8_t clk_adjust;
uint8_t cpo_override;
uint8_t write_data_delay;
} board_memctl_options_t;
static struct board_memctl_options bopts_ctrl[][2] = {
{
/* Controller 0 */
{
/* DDR2 600/667 */
.datarate_mhz_low = 500,
.datarate_mhz_high = 750,
.clk_adjust = 5,
.cpo_override = 8,
.write_data_delay = 2,
},
{
/* DDR2 800 */
.datarate_mhz_low = 750,
.datarate_mhz_high = 850,
.clk_adjust = 5,
.cpo_override = 9,
.write_data_delay = 2,
},
},
{
/* Controller 1 */
{
/* DDR2 600/667 */
.datarate_mhz_low = 500,
.datarate_mhz_high = 750,
.clk_adjust = 5,
.cpo_override = 7,
.write_data_delay = 2,
},
{
/* DDR2 800 */
.datarate_mhz_low = 750,
.datarate_mhz_high = 850,
.clk_adjust = 5,
.cpo_override = 8,
.write_data_delay = 2,
},
},
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
struct board_memctl_options *bopts = bopts_ctrl[ctrl_num];
sys_info_t sysinfo;
int i;
unsigned int datarate;
get_sys_info(&sysinfo);
datarate = get_ddr_freq(0) / 1000000;
for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) {
if ((bopts[i].datarate_mhz_low <= datarate) &&
(bopts[i].datarate_mhz_high >= datarate)) {
debug("controller %d:\n", ctrl_num);
debug(" clk_adjust = %d\n", bopts[i].clk_adjust);
debug(" cpo = %d\n", bopts[i].cpo_override);
debug(" write_data_delay = %d\n",
bopts[i].write_data_delay);
popts->clk_adjust = bopts[i].clk_adjust;
popts->cpo_override = bopts[i].cpo_override;
popts->write_data_delay = bopts[i].write_data_delay;
}
}
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
popts->half_strength_driver_enable = 0;
}
|
