1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
|
/*
* SPDX-License-Identifier: GPL-2.0 IBM-pibs
*/
#include <config.h>
#include <asm/ppc4xx.h>
#define _LINUX_CONFIG_H 1 /* avoid reading Linux autoconf.h file */
#include <ppc_asm.tmpl>
#include <ppc_defs.h>
#include <asm/cache.h>
#include <asm/mmu.h>
/******************************************************************************
* Function: ext_bus_cntlr_init
*
* Description: Configures EBC Controller and a few basic chip selects.
*
* CS0 is setup to get the Boot Flash out of the addresss range
* so that we may setup a stack. CS7 is setup so that we can
* access and reset the hardware watchdog.
*
* IMPORTANT: For pass1 this code must run from
* cache since you can not reliably change a peripheral banks
* timing register (pbxap) while running code from that bank.
* For ex., since we are running from ROM on bank 0, we can NOT
* execute the code that modifies bank 0 timings from ROM, so
* we run it from cache.
*
* Notes: Does NOT use the stack.
*****************************************************************************/
.section ".text"
.align 2
.globl ext_bus_cntlr_init
.type ext_bus_cntlr_init, @function
ext_bus_cntlr_init:
mflr r0
/********************************************************************
* Prefetch entire ext_bus_cntrl_init function into the icache.
* This is necessary because we are going to change the same CS we
* are executing from. Otherwise a CPU lockup may occur.
*******************************************************************/
bl ..getAddr
..getAddr:
mflr r3 /* get address of ..getAddr */
/* Calculate number of cache lines for this function */
addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2)
mtctr r4
..ebcloop:
icbt r0, r3 /* prefetch cache line for addr in r3*/
addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */
bdnz ..ebcloop /* continue for $CTR cache lines */
/********************************************************************
* Delay to ensure all accesses to ROM are complete before changing
* bank 0 timings. 200usec should be enough.
* 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles.
*******************************************************************/
addis r3, 0, 0x0
ori r3, r3, 0xA000 /* wait 200us from reset */
mtctr r3
..spinlp:
bdnz ..spinlp /* spin loop */
/********************************************************************
* Setup External Bus Controller (EBC).
*******************************************************************/
addi r3, 0, EBC0_CFG
mtdcr EBC0_CFGADDR, r3
addis r4, 0, 0xb040 /* Device base timeout = 1024 cycles */
ori r4, r4, 0x0 /* Drive CS with external master */
mtdcr EBC0_CFGDATA, r4
/********************************************************************
* Change PCIINT signal to PerWE
*******************************************************************/
mfdcr r4, CPC0_CR1
ori r4, r4, 0x4000
mtdcr CPC0_CR1, r4
/********************************************************************
* Memory Bank 0 (Flash Bank 0) initialization
*******************************************************************/
addi r3, 0, PB1AP
mtdcr EBC0_CFGADDR, r3
addis r4, 0, CONFIG_SYS_W7O_EBC_PB0AP@h
ori r4, r4, CONFIG_SYS_W7O_EBC_PB0AP@l
mtdcr EBC0_CFGDATA, r4
addi r3, 0, PB0CR
mtdcr EBC0_CFGADDR, r3
addis r4, 0, CONFIG_SYS_W7O_EBC_PB0CR@h
ori r4, r4, CONFIG_SYS_W7O_EBC_PB0CR@l
mtdcr EBC0_CFGDATA, r4
/********************************************************************
* Memory Bank 7 LEDs - NEEDED BECAUSE OF HW WATCHDOG AND LEDs.
*******************************************************************/
addi r3, 0, PB7AP
mtdcr EBC0_CFGADDR, r3
addis r4, 0, CONFIG_SYS_W7O_EBC_PB7AP@h
ori r4, r4, CONFIG_SYS_W7O_EBC_PB7AP@l
mtdcr EBC0_CFGDATA, r4
addi r3, 0, PB7CR
mtdcr EBC0_CFGADDR, r3
addis r4, 0, CONFIG_SYS_W7O_EBC_PB7CR@h
ori r4, r4, CONFIG_SYS_W7O_EBC_PB7CR@l
mtdcr EBC0_CFGDATA, r4
/* We are all done */
mtlr r0 /* Restore link register */
blr /* Return to calling function */
.Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init
/* end ext_bus_cntlr_init() */
/******************************************************************************
* Function: sdram_init
*
* Description: Configures SDRAM memory banks.
*
* Serial Presence Detect, "SPD," reads the SDRAM EEPROM
* via the IIC bus and then configures the SDRAM memory
* banks appropriately. If Auto Memory Configuration is
* is not used, it is assumed that a 4MB 11x8x2, non-ECC,
* SDRAM is soldered down.
*
* Notes: Expects that the stack is already setup.
*****************************************************************************/
.section ".text"
.align 2
.globl sdram_init
.type sdram_init, @function
sdram_init:
/* save the return info on stack */
mflr r0 /* Get link register */
stwu r1, -8(r1) /* Save back chain and move SP */
stw r0, +12(r1) /* Save link register */
/*
* First call spd_sdram to try to init SDRAM according to the
* contents of the SPD EEPROM. If the SPD EEPROM is blank or
* erronious, spd_sdram returns 0 in R3.
*/
li r3,0
bl spd_sdram
addic. r3, r3, 0 /* Check for error, save dram size */
bne ..sdri_done /* If it worked, we're done... */
/********************************************************************
* If SPD detection fails, we'll default to 4MB, 11x8x2, as this
* is the SMALLEST SDRAM size the 405 supports. We can do this
* because W7O boards have soldered on RAM, and there will always
* be some amount present. If we were using DIMMs, we should hang
* the board instead, since it doesn't have any RAM to continue
* running with.
*******************************************************************/
/*
* Disable memory controller to allow
* values to be changed.
*/
addi r3, 0, SDRAM0_CFG
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x0
ori r4, r4, 0x0
mtdcr SDRAM0_CFGDATA, r4
/*
* Set MB0CF for ext bank 0. (0-4MB) Address Mode 5 since 11x8x2
* All other banks are disabled.
*/
addi r3, 0, SDRAM0_B0CR
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x0000 /* BA=0x0, SZ=4MB */
ori r4, r4, 0x8001 /* Mode is 5, 11x8x2or4, BE=Enabled */
mtdcr SDRAM0_CFGDATA, r4
/* Clear MB1CR,MB2CR,MB3CR to turn other banks off */
addi r4, 0, 0 /* Zero the data reg */
addi r3, r3, 4 /* Point to MB1CF reg */
mtdcr SDRAM0_CFGADDR, r3 /* Set the address */
mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */
addi r3, r3, 4 /* Point to MB2CF reg */
mtdcr SDRAM0_CFGADDR, r3 /* Set the address */
mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */
addi r3, r3, 4 /* Point to MB3CF reg */
mtdcr SDRAM0_CFGADDR, r3 /* Set the address */
mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */
/********************************************************************
* Set the SDRAM Timing reg, SDTR1 and the refresh timer reg, RTR.
* To set the appropriate timings, we assume sdram is
* 100MHz (pc100 compliant).
*******************************************************************/
/*
* Set up SDTR1
*/
addi r3, 0, SDRAM0_TR
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x0086 /* SDTR1 value for 100Mhz */
ori r4, r4, 0x400D
mtdcr SDRAM0_CFGDATA, r4
/*
* Set RTR
*/
addi r3, 0, SDRAM0_RTR
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x05F0 /* RTR refresh val = 15.625ms@100Mhz */
mtdcr SDRAM0_CFGDATA, r4
/********************************************************************
* Delay to ensure 200usec have elapsed since reset. Assume worst
* case that the core is running 200Mhz:
* 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
*******************************************************************/
addis r3, 0, 0x0000
ori r3, r3, 0xA000 /* Wait 200us from reset */
mtctr r3
..spinlp2:
bdnz ..spinlp2 /* spin loop */
/********************************************************************
* Set memory controller options reg, MCOPT1.
*******************************************************************/
addi r3, 0, SDRAM0_CFG
mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x80E0 /* DC_EN=1,SRE=0,PME=0,MEMCHK=0 */
ori r4, r4, 0x0000 /* REGEN=0,DRW=00,BRPF=01,ECCDD=1 */
mtdcr SDRAM0_CFGDATA, r4 /* EMDULR=1 */
..sdri_done:
/* restore and return */
lwz r0, +12(r1) /* Get saved link register */
addi r1, r1, +8 /* Remove frame from stack */
mtlr r0 /* Restore link register */
blr /* Return to calling function */
.Lfe1: .size sdram_init,.Lfe1-sdram_init
/* end sdram_init() */
|
