1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
/*
* Copyright 2008-2009 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
#include <common.h>
#include <i2c.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
{
i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr3_spd_eeprom_t));
}
unsigned int fsl_ddr_get_mem_data_rate(void)
{
return get_ddr_freq(0);
}
void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
unsigned int ctrl_num)
{
unsigned int i;
unsigned int i2c_address = 0;
for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
if (ctrl_num == 0 && i == 0)
i2c_address = SPD_EEPROM_ADDRESS1;
get_spd(&(ctrl_dimms_spd[i]), i2c_address);
}
}
typedef struct {
u32 datarate_mhz_low;
u32 datarate_mhz_high;
u32 n_ranks;
u32 clk_adjust;
u32 cpo;
u32 write_data_delay;
u32 force_2T;
} board_specific_parameters_t;
/* ranges for parameters:
* wr_data_delay = 0-6
* clk adjust = 0-8
* cpo 2-0x1E (30)
*/
/* XXX: these values need to be checked for all interleaving modes. */
/* XXX: No reliable dual-rank 800 MHz setting has been found. It may
* seem reliable, but errors will appear when memory intensive
* program is run. */
/* XXX: Single rank at 800 MHz is OK. */
const board_specific_parameters_t board_specific_parameters[][20] = {
{
/* memory controller 0 */
/* lo| hi| num| clk| cpo|wrdata|2T */
/* mhz| mhz|ranks|adjst| | delay| */
{ 0, 333, 2, 6, 7, 3, 0},
{334, 400, 2, 6, 9, 3, 0},
{401, 549, 2, 6, 11, 3, 0},
{550, 680, 2, 1, 10, 5, 0},
{681, 850, 2, 1, 12, 5, 1},
{ 0, 333, 1, 6, 7, 3, 0},
{334, 400, 1, 6, 9, 3, 0},
{401, 549, 1, 6, 11, 3, 0},
{550, 680, 1, 1, 10, 5, 0},
{681, 850, 1, 1, 12, 5, 0}
},
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
const board_specific_parameters_t *pbsp =
&(board_specific_parameters[ctrl_num][0]);
u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
sizeof(board_specific_parameters[0][0]);
u32 i;
ulong ddr_freq;
/* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
* that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
* there are two dimms in the controller, set odt_rd_cfg to 3 and
* odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
*/
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (i&1) { /* odd CS */
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 0;
} else { /* even CS */
if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 4;
} else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
popts->cs_local_opts[i].odt_rd_cfg = 3;
popts->cs_local_opts[i].odt_wr_cfg = 3;
}
}
}
/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
for (i = 0; i < num_params; i++) {
if (ddr_freq >= pbsp->datarate_mhz_low &&
ddr_freq <= pbsp->datarate_mhz_high &&
pdimm->n_ranks == pbsp->n_ranks) {
popts->clk_adjust = pbsp->clk_adjust;
popts->cpo_override = pbsp->cpo;
popts->write_data_delay = pbsp->write_data_delay;
popts->twoT_en = pbsp->force_2T;
}
pbsp++;
}
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
popts->half_strength_driver_enable = 0;
}
|
