1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
|
/*
* Copyright (C) 2009 David Brownell
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <common.h>
#include <nand.h>
#include <asm/io.h>
#include <asm/arch/hardware.h>
#include <asm/arch/emif_defs.h>
#include <asm/arch/nand_defs.h>
#include "../common/misc.h"
#include <net.h>
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
/*
* With the DM355 EVM, u-boot is *always* a third stage loader,
* unless a JTAG debugger handles the first two stages:
*
* - 1st stage is ROM Boot Loader (RBL), which searches for a
* second stage loader in one of three places based on SW7:
* NAND (with MMC/SD fallback), MMC/SD, or UART.
*
* - 2nd stage is User Boot Loader (UBL), using at most 30KB
* of on-chip SRAM, responsible for lowlevel init, and for
* loading the third stage loader into DRAM.
*
* - 3rd stage, that's us!
*/
int board_init(void)
{
gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DM355_EVM;
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
/* We expect the UBL to have handled "lowlevel init", which
* involves setting up at least:
* - clocks
* + PLL1 (for ARM and peripherals) and PLL2 (for DDR)
* + clock divisors for those PLLs
* + LPSC_DDR module enabled
* + LPSC_TIMER0 module (still) enabled
* - EMIF
* + DDR init and timings
* + AEMIF timings (for NAND and DM9000)
* - pinmux
*
* Some of that is repeated here, mostly as a precaution.
*/
/* AEMIF: Some "address" lines are available as GPIOs. A3..A13
* could be too if we used A12 as a GPIO during NAND chipselect
* (and Linux did too), letting us control the LED on A7/GPIO61.
*/
REG(PINMUX2) = 0x0c08;
/* UART0 may still be in SyncReset if we didn't boot from UART */
davinci_enable_uart0();
/* EDMA may be in SyncReset too; turn it on, Linux won't (yet) */
lpsc_on(DAVINCI_LPSC_TPCC);
lpsc_on(DAVINCI_LPSC_TPTC0);
lpsc_on(DAVINCI_LPSC_TPTC1);
return 0;
}
#ifdef CONFIG_DRIVER_DM9000
int board_eth_init(bd_t *bis)
{
return dm9000_initialize(bis);
}
#endif
#ifdef CONFIG_NAND_DAVINCI
static void nand_dm355evm_select_chip(struct mtd_info *mtd, int chip)
{
struct nand_chip *this = mtd->priv;
u32 wbase = (u32) this->IO_ADDR_W;
u32 rbase = (u32) this->IO_ADDR_R;
if (chip == 1) {
__set_bit(14, &wbase);
__set_bit(14, &rbase);
} else {
__clear_bit(14, &wbase);
__clear_bit(14, &rbase);
}
this->IO_ADDR_W = (void *)wbase;
this->IO_ADDR_R = (void *)rbase;
}
int board_nand_init(struct nand_chip *nand)
{
davinci_nand_init(nand);
nand->select_chip = nand_dm355evm_select_chip;
return 0;
}
#endif
|
