1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
|
/*
* (C) Copyright 2007
* Michael Schwingen, michael@schwingen.org
*
* (C) Copyright 2006
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2002
* Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
*
* (C) Copyright 2002
* Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Marius Groeger <mgroeger@sysgo.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <command.h>
#include <malloc.h>
#include <asm/arch/ixp425.h>
#include <asm/io.h>
#include <miiphy.h>
#ifdef CONFIG_PCI
#include <pci.h>
#include <asm/arch/ixp425pci.h>
#endif
#include "actux1_hw.h"
DECLARE_GLOBAL_DATA_PTR;
int board_early_init_f(void)
{
/* CS5: Debug port */
writel(0x9d520003, IXP425_EXP_CS5);
/* CS6: HwRel */
writel(0x81860001, IXP425_EXP_CS6);
/* CS7: LEDs */
writel(0x80900003, IXP425_EXP_CS7);
return 0;
}
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = 0x00000100;
GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
/* Setup GPIOs for PCI INTA */
GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI1_INTA);
GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI1_INTA);
/* Setup GPIOs for 33MHz clock output */
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
writel(0x011001FF, IXP425_GPIO_GPCLKR);
udelay(533);
GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
ACTUX1_LED1(2);
ACTUX1_LED2(2);
ACTUX1_LED3(0);
ACTUX1_LED4(0);
ACTUX1_LED5(0);
ACTUX1_LED6(0);
ACTUX1_LED7(0);
ACTUX1_HS(ACTUX1_HS_DCD);
return 0;
}
/*
* Check Board Identity
*/
int checkboard(void)
{
char buf[64];
int i = getenv_f("serial#", buf, sizeof(buf));
puts("Board: AcTux-1 rev.");
putc(ACTUX1_BOARDREL + 'A' - 1);
if (i > 0) {
puts(", serial# ");
puts(buf);
}
putc('\n');
return 0;
}
/*************************************************************************
* get_board_rev() - setup to pass kernel board revision information
* 0 = reserved
* 1 = Rev. A
* 2 = Rev. B
*************************************************************************/
u32 get_board_rev(void)
{
return ACTUX1_BOARDREL;
}
int dram_init(void)
{
gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
return 0;
}
#ifdef CONFIG_PCI
struct pci_controller hose;
void pci_init_board(void)
{
pci_ixp_init(&hose);
}
#endif
void reset_phy(void)
{
u16 id1, id2;
/* initialize the PHY */
miiphy_reset("NPE0", CONFIG_PHY_ADDR);
miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1);
miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2);
id2 &= 0xFFF0; /* mask out revision bits */
if (id1 == 0x13 && id2 == 0x78e0) {
/*
* LXT971/LXT972 PHY: set LED outputs:
* LED1(green) = Link/ACT,
* LED2 (unused) = LINK,
* LED3(red) = Coll
*/
miiphy_write("NPE0", CONFIG_PHY_ADDR, 20, 0xD432);
} else if (id1 == 0x143 && id2 == 0xbc30) {
/* BCM5241: default values are OK */
} else
printf("unknown ethernet PHY ID: %x %x\n", id1, id2);
}
|
