1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
|
#
# (C) Copyright 2009
# Marvell Semiconductor <www.marvell.com>
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
# MA 02110-1301 USA
#
# Refer docs/README.kwimage for more details about how-to configure
# and create kirkwood boot image
#
# Boot Media configurations
BOOT_FROM nand
NAND_ECC_MODE default
NAND_PAGE_SIZE 0x0800
# SOC registers configuration using bootrom header extension
# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
# Configure RGMII-0 interface pad voltage to 1.8V
DATA 0xFFD100e0 0x1b1b1b9b
#Dram initalization for SINGLE x16 CL=5 @ 400MHz
DATA 0xFFD01400 0x43000c30 # DDR Configuration register
# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
# bit23-14: zero
# bit24: 1= enable exit self refresh mode on DDR access
# bit25: 1 required
# bit29-26: zero
# bit31-30: 01
DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
# bit 4: 0=addr/cmd in smame cycle
# bit 5: 0=clk is driven during self refresh, we don't care for APX
# bit 6: 0=use recommended falling edge of clk for addr/cmd
# bit14: 0=input buffer always powered up
# bit18: 1=cpu lock transaction enabled
# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
# bit30-28: 3 required
# bit31: 0=no additional STARTBURST delay
DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
# bit3-0: TRAS lsbs
# bit7-4: TRCD
# bit11- 8: TRP
# bit15-12: TWR
# bit19-16: TWTR
# bit20: TRAS msb
# bit23-21: 0x0
# bit27-24: TRRD
# bit31-28: TRTP
DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
# bit6-0: TRFC
# bit8-7: TR2R
# bit10-9: TR2W
# bit12-11: TW2W
# bit31-13: zero required
DATA 0xFFD01410 0x000000cc # DDR Address Control
# bit1-0: 00, Cs0width=x8
# bit3-2: 11, Cs0size=1Gb
# bit5-4: 00, Cs1width=x8
# bit7-6: 11, Cs1size=1Gb
# bit9-8: 00, Cs2width=nonexistent
# bit11-10: 00, Cs2size =nonexistent
# bit13-12: 00, Cs3width=nonexistent
# bit15-14: 00, Cs3size =nonexistent
# bit16: 0, Cs0AddrSel
# bit17: 0, Cs1AddrSel
# bit18: 0, Cs2AddrSel
# bit19: 0, Cs3AddrSel
# bit31-20: 0 required
DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
# bit0: 0, OpenPage enabled
# bit31-1: 0 required
DATA 0xFFD01418 0x00000000 # DDR Operation
# bit3-0: 0x0, DDR cmd
# bit31-4: 0 required
DATA 0xFFD0141C 0x00000C52 # DDR Mode
# bit2-0: 2, BurstLen=2 required
# bit3: 0, BurstType=0 required
# bit6-4: 4, CL=5
# bit7: 0, TestMode=0 normal
# bit8: 0, DLL reset=0 normal
# bit11-9: 6, auto-precharge write recovery ????????????
# bit12: 0, PD must be zero
# bit31-13: 0 required
DATA 0xFFD01420 0x00000042 # DDR Extended Mode
# bit0: 0, DDR DLL enabled
# bit1: 1, DDR drive strength reduced
# bit2: 0, DDR ODT control lsd (disabled)
# bit5-3: 000, required
# bit6: 1, DDR ODT control msb, (disabled)
# bit9-7: 000, required
# bit10: 0, differential DQS enabled
# bit11: 0, required
# bit12: 0, DDR output buffer enabled
# bit31-13: 0 required
DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
# bit2-0: 111, required
# bit3 : 1 , MBUS Burst Chop disabled
# bit6-4: 111, required
# bit7 : 0
# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
# bit9 : 0 , no half clock cycle addition to dataout
# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
# bit15-12: 1111 required
# bit31-16: 0 required
DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size
# bit0: 1, Window enabled
# bit1: 0, Write Protect disabled
# bit3-2: 00, CS0 hit selected
# bit23-4: ones, required
# bit31-24: 0x0F, Size (i.e. 256MB)
DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1
DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
DATA 0xFFD01494 0x00120012 # DDR ODT Control (Low)
# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
DATA 0xFFD0149C 0x0000E40f # CPU ODT Control
# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
# bit14: 1, M_STARTBURST_IN ODT: Enabled
# bit15: 1, DDR IO ODT Unit: Use ODT block
DATA 0xFFD01480 0x00000001 # DDR Initialization Control
#bit0=1, enable DDR init upon this register write
# End of Header extension
DATA 0x0 0x0
|
