/* * Generic ULPI interface. * * Copyright (C) 2011 Jana Rapava * Copyright (C) 2011 CompuLab, Ltd. * * Authors: Jana Rapava * Igor Grinberg * * Register offsets taken from: * linux/include/linux/usb/ulpi.h * * Original Copyrights follow: * Copyright (C) 2010 Nokia Corporation * * This software is distributed under the terms of the GNU General * Public License ("GPL") as published by the Free Software Foundation, * version 2 of that License. */ #ifndef __USB_ULPI_H__ #define __USB_ULPI_H__ #define ULPI_ERROR (1 << 8) /* overflow from any register value */ #ifndef CONFIG_USB_ULPI_TIMEOUT #define CONFIG_USB_ULPI_TIMEOUT 1000 /* timeout in us */ #endif /* * Initialize the ULPI transciever and check the interface integrity. * @ulpi_viewport - the address of the ULPI viewport register. * * returns 0 on success, ULPI_ERROR on failure. */ int ulpi_init(u32 ulpi_viewport); /* * Select transceiver speed. * @speed - ULPI_FC_HIGH_SPEED, ULPI_FC_FULL_SPEED (default), * ULPI_FC_LOW_SPEED, ULPI_FC_FS4LS * returns 0 on success, ULPI_ERROR on failure. */ int ulpi_select_transceiver(u32 ulpi_viewport, unsigned speed); /* * Enable/disable VBUS. * @ext_power - external VBUS supply is used (default is false) * @ext_indicator - external VBUS over-current indicator is used * * returns 0 on success, ULPI_ERROR on failure. */ int ulpi_enable_vbus(u32 ulpi_viewport, int on, int ext_power, int ext_ind); /* * Enable/disable pull-down resistors on D+ and D- USB lines. * * returns 0 on success, ULPI_ERROR on failure. */ int ulpi_set_pd(u32 ulpi_viewport, int enable); /* * Select OpMode. * @opmode - ULPI_FC_OPMODE_NORMAL (default), ULPI_FC_OPMODE_NONDRIVING, * ULPI_FC_OPMODE_DISABLE_NRZI, ULPI_FC_OPMODE_NOSYNC_NOEOP * * returns 0 on success, ULPI_ERROR on failure. */ int ulpi_opmode_sel(u32 ulpi_viewport, unsigned opmode); /* * Switch to Serial Mode. * @smode - ULPI_IFACE_6_PIN_SERIAL_MODE or ULPI_IFACE_3_PIN_SERIAL_MODE * * returns 0 on success, ULPI_ERROR on failure. * * Notes: * Switches immediately to Serial Mode. * To return from Serial Mode, STP line needs to be asserted. */ int ulpi_serial_mode_enable(u32 ulpi_viewport, unsigned smode); /* * Put PHY into low power mode. * * returns 0 on success, ULPI_ERROR on failure. * * Notes: * STP line must be driven low to keep the PHY in suspend. * To resume the PHY, STP line needs to be asserted. */ int ulpi_suspend(u32 ulpi_viewport); /* * Reset the transceiver. ULPI interface and registers are not affected. * * returns 0 on success, ULPI_ERROR on failure. */ int ulpi_reset(u32 ulpi_viewport); /* ULPI access methods below must be implemented for each ULPI viewport. */ /* * Write to the ULPI PHY register via the viewport. * @reg - the ULPI register (one of the fields in struct ulpi_regs). * @value - the value - only 8 lower bits are used, others ignored. * * returns 0 on success, ULPI_ERROR on failure. */ u32 ulpi_write(u32 ulpi_viewport, u8 *reg, u32 value); /* * Read the ULPI PHY register content via the viewport. * @reg - the ULPI register (one of the fields in struct ulpi_regs). * * returns register content on success, ULPI_ERROR on failure. */ u32 ulpi_read(u32 ulpi_viewport, u8 *reg); /* * Wait for the reset to complete. * The Link must not attempt to access the PHY until the reset has * completed and DIR line is de-asserted. */ int ulpi_reset_wait(u32 ulpi_viewport); /* Access Extended Register Set (indicator) */ #define ACCESS_EXT_REGS_OFFSET 0x2f /* read-write */ /* Vendor-specific */ #define VENDOR_SPEC_OFFSET 0x30 /* * Extended Register Set * * Addresses 0x00-0x3F map directly to Immediate Register Set. * Addresses 0x40-0x7F are reserved. * Addresses 0x80-0xff are vendor-specific. */ #define EXT_VENDOR_SPEC_OFFSET 0x80 /* ULPI registers, bits and offsets definitions */ struct ulpi_regs { /* Vendor ID and Product ID: 0x00 - 0x03 Read-only */ u8 vendor_id_low; u8 vendor_id_high; u8 product_id_low; u8 product_id_high; /* Function Control: 0x04 - 0x06 Read */ u8 function_ctrl; /* 0x04 Write */ u8 function_ctrl_set; /* 0x05 Set */ u8 function_ctrl_clear; /* 0x06 Clear */ /* Interface Control: 0x07 - 0x09 Read */ u8 iface_ctrl; /* 0x07 Write */ u8 iface_ctrl_set; /* 0x08 Set */ u8 iface_ctrl_clear; /* 0x09 Clear */ /* OTG Control: 0x0A - 0x0C Read */ u8 otg_ctrl; /* 0x0A Write */ u8 otg_ctrl_set; /* 0x0B Set */ u8 otg_ctrl_clear; /* 0x0C Clear */ /* USB Interrupt Enable Rising: 0x0D - 0x0F Read */ u8 usb_ie_rising; /* 0x0D Write */ u8 usb_ie_rising_set; /* 0x0E Set */ u8 usb_ie_rising_clear; /* 0x0F Clear */ /* USB Interrupt Enable Falling: 0x10 - 0x12 Read */ u8 usb_ie_falling; /* 0x10 Write */ u8 usb_ie_falling_set; /* 0x11 Set */ u8 usb_ie_falling_clear; /* 0x12 Clear */ /* USB Interrupt Status: 0x13 Read-only */ u8 usb_int_status; /* USB Interrupt Latch: 0x14 Read-only with auto-clear */ u8 usb_int_latch; /* Debug: 0x15 Read-only */ u8 debug; /* Scratch Register: 0x16 - 0x18 Read */ u8 scratch; /* 0x16 Write */ u8 scratch_set; /* 0x17 Set */ u8 scratch_clear; /* 0x18 Clear */ /* * Optional Carkit registers: * Carkit Control: 0x19 - 0x1B Read */ u8 carkit_ctrl; /* 0x19 Write */ u8 carkit_ctrl_set; /* 0x1A Set */ u8 carkit_ctrl_clear; /* 0x1B Clear */ /* Carkit Interrupt Delay: 0x1C Read, Write */ u8 carkit_int_delay; /* Carkit Interrupt Enable: 0x1D - 0x1F Read */ u8 carkit_ie; /* 0x1D Write */ u8 carkit_ie_set; /* 0x1E Set */ u8 carkit_ie_clear; /* 0x1F Clear */ /* Carkit Interrupt Status: 0x20 Read-only */ u8 carkit_int_status; /* Carkit Interrupt Latch: 0x21 Read-only with auto-clear */ u8 carkit_int_latch; /* Carkit Pulse Control: 0x22 - 0x24 Read */ u8 carkit_pulse_ctrl; /* 0x22 Write */ u8 carkit_pulse_ctrl_set; /* 0x23 Set */ u8 carkit_pulse_ctrl_clear; /* 0x24 Clear */ /* * Other optional registers: * Transmit Positive Width: 0x25 Read, Write */ u8 transmit_pos_width; /* Transmit Negative Width: 0x26 Read, Write */ u8 transmit_neg_width; /* Receive Polarity Recovery: 0x27 Read, Write */ u8 recv_pol_recovery; /* * Addresses 0x28 - 0x2E are reserved, so we use offsets * for immediate registers with higher addresses */ }; /* * Register Bits */ /* Function Control */ #define ULPI_FC_XCVRSEL_MASK (3 << 0) #define ULPI_FC_HIGH_SPEED (0 << 0) #define ULPI_FC_FULL_SPEED (1 << 0) #define ULPI_FC_LOW_SPEED (2 << 0) #define ULPI_FC_FS4LS (3 << 0) #define ULPI_FC_TERMSELECT (1 << 2) #define ULPI_FC_OPMODE_MASK (3 << 3) #define ULPI_FC_OPMODE_NORMAL (0 << 3) #define ULPI_FC_OPMODE_NONDRIVING (1 << 3) #define ULPI_FC_OPMODE_DISABLE_NRZI (2 << 3) #define ULPI_FC_OPMODE_NOSYNC_NOEOP (3 << 3) #define ULPI_FC_RESET (1 << 5) #define ULPI_FC_SUSPENDM (1 << 6) /* Interface Control */ #define ULPI_IFACE_6_PIN_SERIAL_MODE (1 << 0) #define ULPI_IFACE_3_PIN_SERIAL_MODE (1 << 1) #define ULPI_IFACE_CARKITMODE (1 << 2) #define ULPI_IFACE_CLOCKSUSPENDM (1 << 3) #define ULPI_IFACE_AUTORESUME (1 << 4) #define ULPI_IFACE_EXTVBUS_COMPLEMENT (1 << 5) #define ULPI_IFACE_PASSTHRU (1 << 6) #define ULPI_IFACE_PROTECT_IFC_DISABLE (1 << 7) /* OTG Control */ #define ULPI_OTG_ID_PULLUP (1 << 0) #define ULPI_OTG_DP_PULLDOWN (1 << 1) #define ULPI_OTG_DM_PULLDOWN (1 << 2) #define ULPI_OTG_DISCHRGVBUS (1 << 3) #define ULPI_OTG_CHRGVBUS (1 << 4) #define ULPI_OTG_DRVVBUS (1 << 5) #define ULPI_OTG_DRVVBUS_EXT (1 << 6) #define ULPI_OTG_EXTVBUSIND (1 << 7) /* * USB Interrupt Enable Rising, * USB Interrupt Enable Falling, * USB Interrupt Status and * USB Interrupt Latch */ #define ULPI_INT_HOST_DISCONNECT (1 << 0) #define ULPI_INT_VBUS_VALID (1 << 1) #define ULPI_INT_SESS_VALID (1 << 2) #define ULPI_INT_SESS_END (1 << 3) #define ULPI_INT_IDGRD (1 << 4) /* Debug */ #define ULPI_DEBUG_LINESTATE0 (1 << 0) #define ULPI_DEBUG_LINESTATE1 (1 << 1) /* Carkit Control */ #define ULPI_CARKIT_CTRL_CARKITPWR (1 << 0) #define ULPI_CARKIT_CTRL_IDGNDDRV (1 << 1) #define ULPI_CARKIT_CTRL_TXDEN (1 << 2) #define ULPI_CARKIT_CTRL_RXDEN (1 << 3) #define ULPI_CARKIT_CTRL_SPKLEFTEN (1 << 4) #define ULPI_CARKIT_CTRL_SPKRIGHTEN (1 << 5) #define ULPI_CARKIT_CTRL_MICEN (1 << 6) /* Carkit Interrupt Enable */ #define ULPI_CARKIT_INT_EN_IDFLOAT_RISE (1 << 0) #define ULPI_CARKIT_INT_EN_IDFLOAT_FALL (1 << 1) #define ULPI_CARKIT_INT_EN_CARINTDET (1 << 2) #define ULPI_CARKIT_INT_EN_DP_RISE (1 << 3) #define ULPI_CARKIT_INT_EN_DP_FALL (1 << 4) /* Carkit Interrupt Status and Latch */ #define ULPI_CARKIT_INT_IDFLOAT (1 << 0) #define ULPI_CARKIT_INT_CARINTDET (1 << 1) #define ULPI_CARKIT_INT_DP (1 << 2) /* Carkit Pulse Control*/ #define ULPI_CARKIT_PLS_CTRL_TXPLSEN (1 << 0) #define ULPI_CARKIT_PLS_CTRL_RXPLSEN (1 << 1) #define ULPI_CARKIT_PLS_CTRL_SPKRLEFT_BIASEN (1 << 2) #define ULPI_CARKIT_PLS_CTRL_SPKRRIGHT_BIASEN (1 << 3) #endif /* __USB_ULPI_H__ */