/* * (C) Copyright 2001 * Denis Peter, MPL AG Switzerland * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA * * * Most of these definitions are derived from * linux/drivers/scsi/sym53c8xx_defs.h * */ #ifndef _SYM53C8XX_DEFS_H #define _SYM53C8XX_DEFS_H #define SCNTL0 0x00 /* full arb., ena parity, par->ATN */ #define SCNTL1 0x01 /* no reset */ #define ISCON 0x10 /* connected to scsi */ #define CRST 0x08 /* force reset */ #define IARB 0x02 /* immediate arbitration */ #define SCNTL2 0x02 /* no disconnect expected */ #define SDU 0x80 /* cmd: disconnect will raise error */ #define CHM 0x40 /* sta: chained mode */ #define WSS 0x08 /* sta: wide scsi send [W]*/ #define WSR 0x01 /* sta: wide scsi received [W]*/ #define SCNTL3 0x03 /* cnf system clock dependent */ #define EWS 0x08 /* cmd: enable wide scsi [W]*/ #define ULTRA 0x80 /* cmd: ULTRA enable */ /* bits 0-2, 7 rsvd for C1010 */ #define SCID 0x04 /* cnf host adapter scsi address */ #define RRE 0x40 /* r/w:e enable response to resel. */ #define SRE 0x20 /* r/w:e enable response to select */ #define SXFER 0x05 /* ### Sync speed and count */ /* bits 6-7 rsvd for C1010 */ #define SDID 0x06 /* ### Destination-ID */ #define GPREG 0x07 /* ??? IO-Pins */ #define SFBR 0x08 /* ### First byte in phase */ #define SOCL 0x09 #define CREQ 0x80 /* r/w: SCSI-REQ */ #define CACK 0x40 /* r/w: SCSI-ACK */ #define CBSY 0x20 /* r/w: SCSI-BSY */ #define CSEL 0x10 /* r/w: SCSI-SEL */ #define CATN 0x08 /* r/w: SCSI-ATN */ #define CMSG 0x04 /* r/w: SCSI-MSG */ #define CC_D 0x02 /* r/w: SCSI-C_D */ #define CI_O 0x01 /* r/w: SCSI-I_O */ #define SSID 0x0a #define SBCL 0x0b #define DSTAT 0x0c #define DFE 0x80 /* sta: dma fifo empty */ #define MDPE 0x40 /* int: master data parity error */ #define BF 0x20 /* int: script: bus fault */ #define ABRT 0x10 /* int: script: command aborted */ #define SSI 0x08 /* int: script: single step */ #define SIR 0x04 /* int: script: interrupt instruct. */ #define IID 0x01 /* int: script: illegal instruct. */ #define SSTAT0 0x0d #define ILF 0x80 /* sta: data in SIDL register lsb */ #define ORF 0x40 /* sta: data in SODR register lsb */ #define OLF 0x20 /* sta: data in SODL register lsb */ #define AIP 0x10 /* sta: arbitration in progress */ #define LOA 0x08 /* sta: arbitration lost */ #define WOA 0x04 /* sta: arbitration won */ #define IRST 0x02 /* sta: scsi reset signal */ #define SDP 0x01 /* sta: scsi parity signal */ #define SSTAT1 0x0e #define FF3210 0xf0 /* sta: bytes in the scsi fifo */ #define SSTAT2 0x0f #define ILF1 0x80 /* sta: data in SIDL register msb[W]*/ #define ORF1 0x40 /* sta: data in SODR register msb[W]*/ #define OLF1 0x20 /* sta: data in SODL register msb[W]*/ #define DM 0x04 /* sta: DIFFSENS mismatch (895/6 only) */ #define LDSC 0x02 /* sta: disconnect & reconnect */ #define DSA 0x10 /* --> Base page */ #define DSA1 0x11 #define DSA2 0x12 #define DSA3 0x13 #define ISTAT 0x14 /* --> Main Command and status */ #define CABRT 0x80 /* cmd: abort current operation */ #define SRST 0x40 /* mod: reset chip */ #define SIGP 0x20 /* r/w: message from host to ncr */ #define SEM 0x10 /* r/w: message between host + ncr */ #define CON 0x08 /* sta: connected to scsi */ #define INTF 0x04 /* sta: int on the fly (reset by wr)*/ #define SIP 0x02 /* sta: scsi-interrupt */ #define DIP 0x01 /* sta: host/script interrupt */ #define CTEST0 0x18 #define CTEST1 0x19 #define CTEST2 0x1a #define CSIGP 0x40 /* bits 0-2,7 rsvd for C1010 */ #define CTEST3 0x1b #define FLF 0x08 /* cmd: flush dma fifo */ #define CLF 0x04 /* cmd: clear dma fifo */ #define FM 0x02 /* mod: fetch pin mode */ #define WRIE 0x01 /* mod: write and invalidate enable */ /* bits 4-7 rsvd for C1010 */ #define DFIFO 0x20 #define CTEST4 0x21 #define BDIS 0x80 /* mod: burst disable */ #define MPEE 0x08 /* mod: master parity error enable */ #define CTEST5 0x22 #define DFS 0x20 /* mod: dma fifo size */ /* bits 0-1, 3-7 rsvd for C1010 */ #define CTEST6 0x23 #define DBC 0x24 /* ### Byte count and command */ #define DNAD 0x28 /* ### Next command register */ #define DSP 0x2c /* --> Script Pointer */ #define DSPS 0x30 /* --> Script pointer save/opcode#2 */ #define SCRATCHA 0x34 /* Temporary register a */ #define SCRATCHA1 0x35 #define SCRATCHA2 0x36 #define SCRATCHA3 0x37 #define DMODE 0x38 #define BL_2 0x80 /* mod: burst length shift value +2 */ #define BL_1 0x40 /* mod: burst length shift value +1 */ #define ERL 0x08 /* mod: enable read line */ #define ERMP 0x04 /* mod: enable read multiple */ #define BOF 0x02 /* mod: burst op code fetch */ #define MAN 0x01 /* mod: manual start */ #define DIEN 0x39 #define SBR 0x3a #define DCNTL 0x3b /* --> Script execution control */ #define CLSE 0x80 /* mod: cache line size enable */ #define PFF 0x40 /* cmd: pre-fetch flush */ #define PFEN 0x20 /* mod: pre-fetch enable */ #define SSM 0x10 /* mod: single step mode */ #define IRQM 0x08 /* mod: irq mode (1 = totem pole !) */ #define STD 0x04 /* cmd: start dma mode */ #define IRQD 0x02 /* mod: irq disable */ #define NOCOM 0x01 /* cmd: protect sfbr while reselect */ /* bits 0-1 rsvd for C1010 */ #define ADDER 0x3c #define SIEN 0x40 /* -->: interrupt enable */ #define SIST 0x42 /* <--: interrupt status */ #define SBMC 0x1000/* sta: SCSI Bus Mode Change (895/6 only) */ #define STO 0x0400/* sta: timeout (select) */ #define GEN 0x0200/* sta: timeout (general) */ #define HTH 0x0100/* sta: timeout (handshake) */ #define MA 0x80 /* sta: phase mismatch */ #define CMP 0x40 /* sta: arbitration complete */ #define SEL 0x20 /* sta: selected by another device */ #define RSL 0x10 /* sta: reselected by another device*/ #define SGE 0x08 /* sta: gross error (over/underflow)*/ #define UDC 0x04 /* sta: unexpected disconnect */ #define RST 0x02 /* sta: scsi bus reset detected */ #define PAR 0x01 /* sta: scsi parity error */ #define SLPAR 0x44 #define SWIDE 0x45 #define MACNTL 0x46 #define GPCNTL 0x47 #define STIME0 0x48 /* cmd: timeout for select&handshake*/ #define STIME1 0x49 /* cmd: timeout user defined */ #define RESPID 0x4a /* sta: Reselect-IDs */ #define STEST0 0x4c #define STEST1 0x4d #define SCLK 0x80 /* Use the PCI clock as SCSI clock */ #define DBLEN 0x08 /* clock doubler running */ #define DBLSEL 0x04 /* clock doubler selected */ #define STEST2 0x4e #define ROF 0x40 /* reset scsi offset (after gross error!) */ #define EXT 0x02 /* extended filtering */ #define STEST3 0x4f #define TE 0x80 /* c: tolerAnt enable */ #define HSC 0x20 /* c: Halt SCSI Clock */ #define CSF 0x02 /* c: clear scsi fifo */ #define SIDL 0x50 /* Lowlevel: latched from scsi data */ #define STEST4 0x52 #define SMODE 0xc0 /* SCSI bus mode (895/6 only) */ #define SMODE_HVD 0x40 /* High Voltage Differential */ #define SMODE_SE 0x80 /* Single Ended */ #define SMODE_LVD 0xc0 /* Low Voltage Differential */ #define LCKFRQ 0x20 /* Frequency Lock (895/6 only) */ /* bits 0-5 rsvd for C1010 */ #define SODL 0x54 /* Lowlevel: data out to scsi data */ #define SBDL 0x58 /* Lowlevel: data from scsi data */ /*----------------------------------------------------------- ** ** Utility macros for the script. ** **----------------------------------------------------------- */ #define REG(r) (r) /*----------------------------------------------------------- ** ** SCSI phases ** ** DT phases illegal for ncr driver. ** **----------------------------------------------------------- */ #define SCR_DATA_OUT 0x00000000 #define SCR_DATA_IN 0x01000000 #define SCR_COMMAND 0x02000000 #define SCR_STATUS 0x03000000 #define SCR_DT_DATA_OUT 0x04000000 #define SCR_DT_DATA_IN 0x05000000 #define SCR_MSG_OUT 0x06000000 #define SCR_MSG_IN 0x07000000 #define SCR_ILG_OUT 0x04000000 #define SCR_ILG_IN 0x05000000 /*----------------------------------------------------------- ** ** Data transfer via SCSI. ** **----------------------------------------------------------- ** ** MOVE_ABS (LEN) ** <<start address>> ** ** MOVE_IND (LEN) ** <<dnad_offset>> ** ** MOVE_TBL ** <<dnad_offset>> ** **----------------------------------------------------------- */ #define OPC_MOVE 0x08000000 #define SCR_MOVE_ABS(l) ((0x00000000 | OPC_MOVE) | (l)) #define SCR_MOVE_IND(l) ((0x20000000 | OPC_MOVE) | (l)) #define SCR_MOVE_TBL (0x10000000 | OPC_MOVE) #define SCR_CHMOV_ABS(l) ((0x00000000) | (l)) #define SCR_CHMOV_IND(l) ((0x20000000) | (l)) #define SCR_CHMOV_TBL (0x10000000) /*----------------------------------------------------------- ** ** Selection ** **----------------------------------------------------------- ** ** SEL_ABS | SCR_ID (0..15) [ | REL_JMP] ** <<alternate_address>> ** ** SEL_TBL | << dnad_offset>> [ | REL_JMP] ** <<alternate_address>> ** **----------------------------------------------------------- */ #define SCR_SEL_ABS 0x40000000 #define SCR_SEL_ABS_ATN 0x41000000 #define SCR_SEL_TBL 0x42000000 #define SCR_SEL_TBL_ATN 0x43000000 #define SCR_JMP_REL 0x04000000 #define SCR_ID(id) (((unsigned long)(id)) << 16) /*----------------------------------------------------------- ** ** Waiting for Disconnect or Reselect ** **----------------------------------------------------------- ** ** WAIT_DISC ** dummy: <<alternate_address>> ** ** WAIT_RESEL ** <<alternate_address>> ** **----------------------------------------------------------- */ #define SCR_WAIT_DISC 0x48000000 #define SCR_WAIT_RESEL 0x50000000 /*----------------------------------------------------------- ** ** Bit Set / Reset ** **----------------------------------------------------------- ** ** SET (flags {|.. }) ** ** CLR (flags {|.. }) ** **----------------------------------------------------------- */ #define SCR_SET(f) (0x58000000 | (f)) #define SCR_CLR(f) (0x60000000 | (f)) #define SCR_CARRY 0x00000400 #define SCR_TRG 0x00000200 #define SCR_ACK 0x00000040 #define SCR_ATN 0x00000008 /*----------------------------------------------------------- ** ** Memory to memory move ** **----------------------------------------------------------- ** ** COPY (bytecount) ** << source_address >> ** << destination_address >> ** ** SCR_COPY sets the NO FLUSH option by default. ** SCR_COPY_F does not set this option. ** ** For chips which do not support this option, ** ncr_copy_and_bind() will remove this bit. **----------------------------------------------------------- */ #define SCR_NO_FLUSH 0x01000000 #define SCR_COPY(n) (0xc0000000 | SCR_NO_FLUSH | (n)) #define SCR_COPY_F(n) (0xc0000000 | (n)) /*----------------------------------------------------------- ** ** Register move and binary operations ** **----------------------------------------------------------- ** ** SFBR_REG (reg, op, data) reg = SFBR op data ** << 0 >> ** ** REG_SFBR (reg, op, data) SFBR = reg op data ** << 0 >> ** ** REG_REG (reg, op, data) reg = reg op data ** << 0 >> ** **----------------------------------------------------------- ** On 810A, 860, 825A, 875, 895 and 896 chips the content ** of SFBR register can be used as data (SCR_SFBR_DATA). ** The 896 has additionnal IO registers starting at ** offset 0x80. Bit 7 of register offset is stored in ** bit 7 of the SCRIPTS instruction first DWORD. **----------------------------------------------------------- */ #define SCR_REG_OFS(ofs) ((((ofs) & 0x7f) << 16ul)) /* + ((ofs) & 0x80)) */ #define SCR_SFBR_REG(reg,op,data) \ (0x68000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) #define SCR_REG_SFBR(reg,op,data) \ (0x70000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) #define SCR_REG_REG(reg,op,data) \ (0x78000000 | (SCR_REG_OFS(REG(reg))) | (op) | (((data)&0xff)<<8ul)) #define SCR_LOAD 0x00000000 #define SCR_SHL 0x01000000 #define SCR_OR 0x02000000 #define SCR_XOR 0x03000000 #define SCR_AND 0x04000000 #define SCR_SHR 0x05000000 #define SCR_ADD 0x06000000 #define SCR_ADDC 0x07000000 #define SCR_SFBR_DATA (0x00800000>>8ul) /* Use SFBR as data */ /*----------------------------------------------------------- ** ** FROM_REG (reg) SFBR = reg ** << 0 >> ** ** TO_REG (reg) reg = SFBR ** << 0 >> ** ** LOAD_REG (reg, data) reg = <data> ** << 0 >> ** ** LOAD_SFBR(data) SFBR = <data> ** << 0 >> ** **----------------------------------------------------------- */ #define SCR_FROM_REG(reg) \ SCR_REG_SFBR(reg,SCR_OR,0) #define SCR_TO_REG(reg) \ SCR_SFBR_REG(reg,SCR_OR,0) #define SCR_LOAD_REG(reg,data) \ SCR_REG_REG(reg,SCR_LOAD,data) #define SCR_LOAD_SFBR(data) \ (SCR_REG_SFBR (gpreg, SCR_LOAD, data)) /*----------------------------------------------------------- ** ** LOAD from memory to register. ** STORE from register to memory. ** ** Only supported by 810A, 860, 825A, 875, 895 and 896. ** **----------------------------------------------------------- ** ** LOAD_ABS (LEN) ** <<start address>> ** ** LOAD_REL (LEN) (DSA relative) ** <<dsa_offset>> ** **----------------------------------------------------------- */ #define SCR_REG_OFS2(ofs) (((ofs) & 0xff) << 16ul) #define SCR_NO_FLUSH2 0x02000000 #define SCR_DSA_REL2 0x10000000 #define SCR_LOAD_R(reg, how, n) \ (0xe1000000 | how | (SCR_REG_OFS2(REG(reg))) | (n)) #define SCR_STORE_R(reg, how, n) \ (0xe0000000 | how | (SCR_REG_OFS2(REG(reg))) | (n)) #define SCR_LOAD_ABS(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2, n) #define SCR_LOAD_REL(reg, n) SCR_LOAD_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2, n) #define SCR_LOAD_ABS_F(reg, n) SCR_LOAD_R(reg, 0, n) #define SCR_LOAD_REL_F(reg, n) SCR_LOAD_R(reg, SCR_DSA_REL2, n) #define SCR_STORE_ABS(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2, n) #define SCR_STORE_REL(reg, n) SCR_STORE_R(reg, SCR_NO_FLUSH2|SCR_DSA_REL2,n) #define SCR_STORE_ABS_F(reg, n) SCR_STORE_R(reg, 0, n) #define SCR_STORE_REL_F(reg, n) SCR_STORE_R(reg, SCR_DSA_REL2, n) /*----------------------------------------------------------- ** ** Waiting for Disconnect or Reselect ** **----------------------------------------------------------- ** ** JUMP [ | IFTRUE/IFFALSE ( ... ) ] ** <<address>> ** ** JUMPR [ | IFTRUE/IFFALSE ( ... ) ] ** <<distance>> ** ** CALL [ | IFTRUE/IFFALSE ( ... ) ] ** <<address>> ** ** CALLR [ | IFTRUE/IFFALSE ( ... ) ] ** <<distance>> ** ** RETURN [ | IFTRUE/IFFALSE ( ... ) ] ** <<dummy>> ** ** INT [ | IFTRUE/IFFALSE ( ... ) ] ** <<ident>> ** ** INT_FLY [ | IFTRUE/IFFALSE ( ... ) ] ** <<ident>> ** ** Conditions: ** WHEN (phase) ** IF (phase) ** CARRYSET ** DATA (data, mask) ** **----------------------------------------------------------- */ #define SCR_NO_OP 0x80000000 #define SCR_JUMP 0x80080000 #define SCR_JUMP64 0x80480000 #define SCR_JUMPR 0x80880000 #define SCR_CALL 0x88080000 #define SCR_CALLR 0x88880000 #define SCR_RETURN 0x90080000 #define SCR_INT 0x98080000 #define SCR_INT_FLY 0x98180000 #define IFFALSE(arg) (0x00080000 | (arg)) #define IFTRUE(arg) (0x00000000 | (arg)) #define WHEN(phase) (0x00030000 | (phase)) #define IF(phase) (0x00020000 | (phase)) #define DATA(D) (0x00040000 | ((D) & 0xff)) #define MASK(D,M) (0x00040000 | (((M ^ 0xff) & 0xff) << 8ul)|((D) & 0xff)) #define CARRYSET (0x00200000) #define SIR_COMPLETE 0x10000000 /* script errors */ #define SIR_SEL_ATN_NO_MSG_OUT 0x00000001 #define SIR_CMD_OUT_ILL_PH 0x00000002 #define SIR_STATUS_ILL_PH 0x00000003 #define SIR_MSG_RECEIVED 0x00000004 #define SIR_DATA_IN_ERR 0x00000005 #define SIR_DATA_OUT_ERR 0x00000006 #define SIR_SCRIPT_ERROR 0x00000007 #define SIR_MSG_OUT_NO_CMD 0x00000008 #define SIR_MSG_OVER7 0x00000009 /* Fly interrupt */ #define INT_ON_FY 0x00000080 /* Hardware errors are defined in scsi.h */ #define SCSI_IDENTIFY 0xC0 #ifndef TRUE #define TRUE 1 #endif #ifndef FALSE #define FALSE 0 #endif #endif