/* * linux/include/linux/mtd/nand.h * * Copyright (c) 2000 David Woodhouse * Steven J. Hill * Thomas Gleixner * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * * Info: * Contains standard defines and IDs for NAND flash devices * * Changelog: * See git changelog. */ #ifndef __LINUX_MTD_NAND_H #define __LINUX_MTD_NAND_H /* XXX U-BOOT XXX */ #if 0 #include #include #include #endif #include "config.h" #include "linux/mtd/compat.h" #include "linux/mtd/mtd.h" #include "linux/mtd/bbm.h" struct mtd_info; /* Scan and identify a NAND device */ extern int nand_scan (struct mtd_info *mtd, int max_chips); /* Separate phases of nand_scan(), allowing board driver to intervene * and override command or ECC setup according to flash type */ extern int nand_scan_ident(struct mtd_info *mtd, int max_chips); extern int nand_scan_tail(struct mtd_info *mtd); /* Free resources held by the NAND device */ extern void nand_release (struct mtd_info *mtd); /* Internal helper for board drivers which need to override command function */ extern void nand_wait_ready(struct mtd_info *mtd); /* This constant declares the max. oobsize / page, which * is supported now. If you add a chip with bigger oobsize/page * adjust this accordingly. */ #define NAND_MAX_OOBSIZE (218 * CONFIG_SYS_NAND_MAX_CHIPS) #define NAND_MAX_PAGESIZE (4096 * CONFIG_SYS_NAND_MAX_CHIPS) /* * Constants for hardware specific CLE/ALE/NCE function * * These are bits which can be or'ed to set/clear multiple * bits in one go. */ /* Select the chip by setting nCE to low */ #define NAND_NCE 0x01 /* Select the command latch by setting CLE to high */ #define NAND_CLE 0x02 /* Select the address latch by setting ALE to high */ #define NAND_ALE 0x04 #define NAND_CTRL_CLE (NAND_NCE | NAND_CLE) #define NAND_CTRL_ALE (NAND_NCE | NAND_ALE) #define NAND_CTRL_CHANGE 0x80 /* * Standard NAND flash commands */ #define NAND_CMD_READ0 0 #define NAND_CMD_READ1 1 #define NAND_CMD_RNDOUT 5 #define NAND_CMD_PAGEPROG 0x10 #define NAND_CMD_READOOB 0x50 #define NAND_CMD_ERASE1 0x60 #define NAND_CMD_STATUS 0x70 #define NAND_CMD_STATUS_MULTI 0x71 #define NAND_CMD_SEQIN 0x80 #define NAND_CMD_RNDIN 0x85 #define NAND_CMD_READID 0x90 #define NAND_CMD_ERASE2 0xd0 #define NAND_CMD_RESET 0xff /* Extended commands for large page devices */ #define NAND_CMD_READSTART 0x30 #define NAND_CMD_RNDOUTSTART 0xE0 #define NAND_CMD_CACHEDPROG 0x15 /* Extended commands for AG-AND device */ /* * Note: the command for NAND_CMD_DEPLETE1 is really 0x00 but * there is no way to distinguish that from NAND_CMD_READ0 * until the remaining sequence of commands has been completed * so add a high order bit and mask it off in the command. */ #define NAND_CMD_DEPLETE1 0x100 #define NAND_CMD_DEPLETE2 0x38 #define NAND_CMD_STATUS_MULTI 0x71 #define NAND_CMD_STATUS_ERROR 0x72 /* multi-bank error status (banks 0-3) */ #define NAND_CMD_STATUS_ERROR0 0x73 #define NAND_CMD_STATUS_ERROR1 0x74 #define NAND_CMD_STATUS_ERROR2 0x75 #define NAND_CMD_STATUS_ERROR3 0x76 #define NAND_CMD_STATUS_RESET 0x7f #define NAND_CMD_STATUS_CLEAR 0xff #define NAND_CMD_NONE -1 /* Status bits */ #define NAND_STATUS_FAIL 0x01 #define NAND_STATUS_FAIL_N1 0x02 #define NAND_STATUS_TRUE_READY 0x20 #define NAND_STATUS_READY 0x40 #define NAND_STATUS_WP 0x80 /* * Constants for ECC_MODES */ typedef enum { NAND_ECC_NONE, NAND_ECC_SOFT, NAND_ECC_HW, NAND_ECC_HW_SYNDROME, } nand_ecc_modes_t; /* * Constants for Hardware ECC */ /* Reset Hardware ECC for read */ #define NAND_ECC_READ 0 /* Reset Hardware ECC for write */ #define NAND_ECC_WRITE 1 /* Enable Hardware ECC before syndrom is read back from flash */ #define NAND_ECC_READSYN 2 /* Bit mask for flags passed to do_nand_read_ecc */ #define NAND_GET_DEVICE 0x80 /* Option constants for bizarre disfunctionality and real * features */ /* Chip can not auto increment pages */ #define NAND_NO_AUTOINCR 0x00000001 /* Buswitdh is 16 bit */ #define NAND_BUSWIDTH_16 0x00000002 /* Device supports partial programming without padding */ #define NAND_NO_PADDING 0x00000004 /* Chip has cache program function */ #define NAND_CACHEPRG 0x00000008 /* Chip has copy back function */ #define NAND_COPYBACK 0x00000010 /* AND Chip which has 4 banks and a confusing page / block * assignment. See Renesas datasheet for further information */ #define NAND_IS_AND 0x00000020 /* Chip has a array of 4 pages which can be read without * additional ready /busy waits */ #define NAND_4PAGE_ARRAY 0x00000040 /* Chip requires that BBT is periodically rewritten to prevent * bits from adjacent blocks from 'leaking' in altering data. * This happens with the Renesas AG-AND chips, possibly others. */ #define BBT_AUTO_REFRESH 0x00000080 /* Chip does not require ready check on read. True * for all large page devices, as they do not support * autoincrement.*/ #define NAND_NO_READRDY 0x00000100 /* Chip does not allow subpage writes */ #define NAND_NO_SUBPAGE_WRITE 0x00000200 /* Options valid for Samsung large page devices */ #define NAND_SAMSUNG_LP_OPTIONS \ (NAND_NO_PADDING | NAND_CACHEPRG | NAND_COPYBACK) /* Macros to identify the above */ #define NAND_CANAUTOINCR(chip) (!(chip->options & NAND_NO_AUTOINCR)) #define NAND_MUST_PAD(chip) (!(chip->options & NAND_NO_PADDING)) #define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG)) #define NAND_HAS_COPYBACK(chip) ((chip->options & NAND_COPYBACK)) /* Large page NAND with SOFT_ECC should support subpage reads */ #define NAND_SUBPAGE_READ(chip) ((chip->ecc.mode == NAND_ECC_SOFT) \ && (chip->page_shift > 9)) /* Mask to zero out the chip options, which come from the id table */ #define NAND_CHIPOPTIONS_MSK (0x0000ffff & ~NAND_NO_AUTOINCR) /* Non chip related options */ /* Use a flash based bad block table. This option is passed to the * default bad block table function. */ #define NAND_USE_FLASH_BBT 0x00010000 /* This option skips the bbt scan during initialization. */ #define NAND_SKIP_BBTSCAN 0x00020000 /* This option is defined if the board driver allocates its own buffers (e.g. because it needs them DMA-coherent */ #define NAND_OWN_BUFFERS 0x00040000 /* Options set by nand scan */ /* bbt has already been read */ #define NAND_BBT_SCANNED 0x40000000 /* Nand scan has allocated controller struct */ #define NAND_CONTROLLER_ALLOC 0x80000000 /* Cell info constants */ #define NAND_CI_CHIPNR_MSK 0x03 #define NAND_CI_CELLTYPE_MSK 0x0C /* Keep gcc happy */ struct nand_chip; /** * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices * @lock: protection lock * @active: the mtd device which holds the controller currently * @wq: wait queue to sleep on if a NAND operation is in progress * used instead of the per chip wait queue when a hw controller is available */ struct nand_hw_control { /* XXX U-BOOT XXX */ #if 0 spinlock_t lock; wait_queue_head_t wq; #endif struct nand_chip *active; }; /** * struct nand_ecc_ctrl - Control structure for ecc * @mode: ecc mode * @steps: number of ecc steps per page * @size: data bytes per ecc step * @bytes: ecc bytes per step * @total: total number of ecc bytes per page * @prepad: padding information for syndrome based ecc generators * @postpad: padding information for syndrome based ecc generators * @layout: ECC layout control struct pointer * @hwctl: function to control hardware ecc generator. Must only * be provided if an hardware ECC is available * @calculate: function for ecc calculation or readback from ecc hardware * @correct: function for ecc correction, matching to ecc generator (sw/hw) * @read_page_raw: function to read a raw page without ECC * @write_page_raw: function to write a raw page without ECC * @read_page: function to read a page according to the ecc generator requirements * @write_page: function to write a page according to the ecc generator requirements * @read_oob: function to read chip OOB data * @write_oob: function to write chip OOB data */ struct nand_ecc_ctrl { nand_ecc_modes_t mode; int steps; int size; int bytes; int total; int prepad; int postpad; struct nand_ecclayout *layout; void (*hwctl)(struct mtd_info *mtd, int mode); int (*calculate)(struct mtd_info *mtd, const uint8_t *dat, uint8_t *ecc_code); int (*correct)(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc, uint8_t *calc_ecc); int (*read_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf); void (*write_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf); int (*read_page)(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf); int (*read_subpage)(struct mtd_info *mtd, struct nand_chip *chip, uint32_t offs, uint32_t len, uint8_t *buf); void (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf); int (*read_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page, int sndcmd); int (*write_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page); }; /** * struct nand_buffers - buffer structure for read/write * @ecccalc: buffer for calculated ecc * @ecccode: buffer for ecc read from flash * @databuf: buffer for data - dynamically sized * * Do not change the order of buffers. databuf and oobrbuf must be in * consecutive order. */ struct nand_buffers { uint8_t ecccalc[NAND_MAX_OOBSIZE]; uint8_t ecccode[NAND_MAX_OOBSIZE]; uint8_t databuf[NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE]; }; /** * struct nand_chip - NAND Private Flash Chip Data * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device * @read_byte: [REPLACEABLE] read one byte from the chip * @read_word: [REPLACEABLE] read one word from the chip * @write_buf: [REPLACEABLE] write data from the buffer to the chip * @read_buf: [REPLACEABLE] read data from the chip into the buffer * @verify_buf: [REPLACEABLE] verify buffer contents against the chip data * @select_chip: [REPLACEABLE] select chip nr * @block_bad: [REPLACEABLE] check, if the block is bad * @block_markbad: [REPLACEABLE] mark the block bad * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific funtion for controlling * ALE/CLE/nCE. Also used to write command and address * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line * If set to NULL no access to ready/busy is available and the ready/busy information * is read from the chip status register * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing commands to the chip * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on ready * @ecc: [BOARDSPECIFIC] ecc control ctructure * @buffers: buffer structure for read/write * @hwcontrol: platform-specific hardware control structure * @ops: oob operation operands * @erase_cmd: [INTERN] erase command write function, selectable due to AND support * @scan_bbt: [REPLACEABLE] function to scan bad block table * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR) * @wq: [INTERN] wait queue to sleep on if a NAND operation is in progress * @state: [INTERN] the current state of the NAND device * @oob_poi: poison value buffer * @page_shift: [INTERN] number of address bits in a page (column address bits) * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry * @chip_shift: [INTERN] number of address bits in one chip * @datbuf: [INTERN] internal buffer for one page + oob * @oobbuf: [INTERN] oob buffer for one eraseblock * @oobdirty: [INTERN] indicates that oob_buf must be reinitialized * @data_poi: [INTERN] pointer to a data buffer * @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about * special functionality. See the defines for further explanation * @badblockpos: [INTERN] position of the bad block marker in the oob area * @cellinfo: [INTERN] MLC/multichip data from chip ident * @numchips: [INTERN] number of physical chips * @chipsize: [INTERN] the size of one chip for multichip arrays * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1 * @pagebuf: [INTERN] holds the pagenumber which is currently in data_buf * @subpagesize: [INTERN] holds the subpagesize * @ecclayout: [REPLACEABLE] the default ecc placement scheme * @bbt: [INTERN] bad block table pointer * @bbt_td: [REPLACEABLE] bad block table descriptor for flash lookup * @bbt_md: [REPLACEABLE] bad block table mirror descriptor * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial bad block scan * @controller: [REPLACEABLE] a pointer to a hardware controller structure * which is shared among multiple independend devices * @priv: [OPTIONAL] pointer to private chip date * @errstat: [OPTIONAL] hardware specific function to perform additional error status checks * (determine if errors are correctable) * @write_page: [REPLACEABLE] High-level page write function */ struct nand_chip { void __iomem *IO_ADDR_R; void __iomem *IO_ADDR_W; uint8_t (*read_byte)(struct mtd_info *mtd); u16 (*read_word)(struct mtd_info *mtd); void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); int (*verify_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); void (*select_chip)(struct mtd_info *mtd, int chip); int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip); int (*block_markbad)(struct mtd_info *mtd, loff_t ofs); void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl); int (*dev_ready)(struct mtd_info *mtd); void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr); int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this); void (*erase_cmd)(struct mtd_info *mtd, int page); int (*scan_bbt)(struct mtd_info *mtd); int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state, int status, int page); int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int page, int cached, int raw); int chip_delay; unsigned int options; int page_shift; int phys_erase_shift; int bbt_erase_shift; int chip_shift; int numchips; uint64_t chipsize; int pagemask; int pagebuf; int subpagesize; uint8_t cellinfo; int badblockpos; int state; uint8_t *oob_poi; struct nand_hw_control *controller; struct nand_ecclayout *ecclayout; struct nand_ecc_ctrl ecc; struct nand_buffers *buffers; struct nand_hw_control hwcontrol; struct mtd_oob_ops ops; uint8_t *bbt; struct nand_bbt_descr *bbt_td; struct nand_bbt_descr *bbt_md; struct nand_bbt_descr *badblock_pattern; void *priv; }; /* * NAND Flash Manufacturer ID Codes */ #define NAND_MFR_TOSHIBA 0x98 #define NAND_MFR_SAMSUNG 0xec #define NAND_MFR_FUJITSU 0x04 #define NAND_MFR_NATIONAL 0x8f #define NAND_MFR_RENESAS 0x07 #define NAND_MFR_STMICRO 0x20 #define NAND_MFR_HYNIX 0xad #define NAND_MFR_MICRON 0x2c #define NAND_MFR_AMD 0x01 #define NAND_MFR_SANDISK 0x45 #define NAND_MFR_INTEL 0x89 /** * struct nand_flash_dev - NAND Flash Device ID Structure * @name: Identify the device type * @id: device ID code * @pagesize: Pagesize in bytes. Either 256 or 512 or 0 * If the pagesize is 0, then the real pagesize * and the eraseize are determined from the * extended id bytes in the chip * @erasesize: Size of an erase block in the flash device. * @chipsize: Total chipsize in Mega Bytes * @options: Bitfield to store chip relevant options */ struct nand_flash_dev { char *name; int id; unsigned long pagesize; unsigned long chipsize; unsigned long erasesize; unsigned long options; }; /** * struct nand_manufacturers - NAND Flash Manufacturer ID Structure * @name: Manufacturer name * @id: manufacturer ID code of device. */ struct nand_manufacturers { int id; char * name; }; extern struct nand_flash_dev nand_flash_ids[]; extern struct nand_manufacturers nand_manuf_ids[]; extern int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd); extern int nand_update_bbt(struct mtd_info *mtd, loff_t offs); extern int nand_default_bbt(struct mtd_info *mtd); extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt); extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, int allowbbt); extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len, size_t * retlen, uint8_t * buf); /* * Constants for oob configuration */ #define NAND_SMALL_BADBLOCK_POS 5 #define NAND_LARGE_BADBLOCK_POS 0 /** * struct platform_nand_chip - chip level device structure * @nr_chips: max. number of chips to scan for * @chip_offset: chip number offset * @nr_partitions: number of partitions pointed to by partitions (or zero) * @partitions: mtd partition list * @chip_delay: R/B delay value in us * @options: Option flags, e.g. 16bit buswidth * @ecclayout: ecc layout info structure * @part_probe_types: NULL-terminated array of probe types * @priv: hardware controller specific settings */ struct platform_nand_chip { int nr_chips; int chip_offset; int nr_partitions; struct mtd_partition *partitions; struct nand_ecclayout *ecclayout; int chip_delay; unsigned int options; const char **part_probe_types; void *priv; }; /** * struct platform_nand_ctrl - controller level device structure * @hwcontrol: platform specific hardware control structure * @dev_ready: platform specific function to read ready/busy pin * @select_chip: platform specific chip select function * @cmd_ctrl: platform specific function for controlling * ALE/CLE/nCE. Also used to write command and address * @priv: private data to transport driver specific settings * * All fields are optional and depend on the hardware driver requirements */ struct platform_nand_ctrl { void (*hwcontrol)(struct mtd_info *mtd, int cmd); int (*dev_ready)(struct mtd_info *mtd); void (*select_chip)(struct mtd_info *mtd, int chip); void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl); void *priv; }; /** * struct platform_nand_data - container structure for platform-specific data * @chip: chip level chip structure * @ctrl: controller level device structure */ struct platform_nand_data { struct platform_nand_chip chip; struct platform_nand_ctrl ctrl; }; /* Some helpers to access the data structures */ static inline struct platform_nand_chip *get_platform_nandchip(struct mtd_info *mtd) { struct nand_chip *chip = mtd->priv; return chip->priv; } #endif /* __LINUX_MTD_NAND_H */