/* * (C) Copyright 2008 * Gary Jennejohn, DENX Software Engineering GmbH, garyj@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /************************************************************************ * quad100hd.h - configuration for Quad100hd board ***********************************************************************/ #ifndef __CONFIG_H #define __CONFIG_H /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ #define CONFIG_QUAD100HD 1 /* Board is Quad100hd */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_405EP 1 /* Specifc 405EP support*/ #define CONFIG_SYS_TEXT_BASE 0xFFFC0000 #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define PLLMR0_DEFAULT PLLMR0_266_133_66 /* no PCI */ #define PLLMR1_DEFAULT PLLMR1_266_133_66 /* no PCI */ /* the environment is in the EEPROM by default */ #define CONFIG_ENV_IS_IN_EEPROM #undef CONFIG_ENV_IS_IN_FLASH #define CONFIG_PPC4xx_EMAC #define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0x01 /* PHY address */ #define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_PHY_RESET 1 #define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */ /* * Command line configuration. */ #include #undef CONFIG_CMD_ASKENV #undef CONFIG_CMD_CACHE #define CONFIG_CMD_DHCP #undef CONFIG_CMD_DIAG #define CONFIG_CMD_EEPROM #undef CONFIG_CMD_ELF #define CONFIG_CMD_I2C #undef CONFIG_CMD_IRQ #define CONFIG_CMD_JFFS2 #undef CONFIG_CMD_LOG #undef CONFIG_CMD_MII #define CONFIG_CMD_NAND #undef CONFIG_CMD_PING #define CONFIG_CMD_REGINFO #undef CONFIG_WATCHDOG /* watchdog disabled */ /*----------------------------------------------------------------------- * SDRAM *----------------------------------------------------------------------*/ /* * SDRAM configuration (please see cpu/ppc/sdram.[ch]) */ #define CONFIG_SDRAM_BANK0 1 /* FIX! SDRAM timings used in datasheet */ #define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */ #define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */ #define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */ #define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ #define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */ /* * JFFS2 */ #define CONFIG_SYS_JFFS2_FIRST_BANK 0 #ifdef CONFIG_SYS_KERNEL_IN_JFFS2 #define CONFIG_SYS_JFFS2_FIRST_SECTOR 0 /* JFFS starts at block 0 */ #else /* kernel not in JFFS */ #define CONFIG_SYS_JFFS2_FIRST_SECTOR 8 /* block 0-7 is kernel (1MB = 8 sectors) */ #endif #define CONFIG_SYS_JFFS2_NUM_BANKS 1 /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #define CONFIG_SYS_BASE_BAUD 691200 #define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} /*----------------------------------------------------------------------- * Miscellaneous configurable options *----------------------------------------------------------------------*/ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* bytes of address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 8 byte write page size */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CONFIG_SYS_EEPROM_SIZE 0x2000 /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFFC00000 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE) /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ /* the environment is located before u-boot */ #define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE - CONFIG_ENV_SECT_SIZE) /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) #endif #ifdef CONFIG_ENV_IS_IN_EEPROM #define CONFIG_ENV_SIZE 0x400 /* Size of Environment vars */ #define CONFIG_ENV_OFFSET 0x00000000 #define CONFIG_SYS_ENABLE_CRC_16 1 /* Intrinsyc formatting used crc16 */ #endif /* partly from PPCBoot */ /* NAND */ #define CONFIG_NAND #ifdef CONFIG_NAND #define CONFIG_SYS_NAND_BASE 0x60000000 #define CONFIG_SYS_NAND_CS 10 /* our CS is GPIO10 */ #define CONFIG_SYS_NAND_RDY 23 /* our RDY is GPIO23 */ #define CONFIG_SYS_NAND_CE 24 /* our CE is GPIO24 */ #define CONFIG_SYS_NAND_CLE 31 /* our CLE is GPIO31 */ #define CONFIG_SYS_NAND_ALE 30 /* our ALE is GPIO30 */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #endif /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in data cache) */ /* use on chip memory (OCM) for temperary stack until sdram is tested */ /* see ./arch/powerpc/cpu/ppc4xx/start.S */ #define CONFIG_SYS_TEMP_STACK_OCM 1 /* On Chip Memory location */ #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of OCM */ #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup * Taken from PPCBoot board/icecube/icecube.h */ /* see ./arch/powerpc/cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/ndfc.c */ #define CONFIG_SYS_EBC_PB0AP 0x04002480 /* AMD NOR flash - this corresponds to FLASH_BASE so may be correct */ #define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 #define CONFIG_SYS_EBC_PB1AP 0x04005480 #define CONFIG_SYS_EBC_PB1CR 0x60018000 #define CONFIG_SYS_EBC_PB2AP 0x00000000 #define CONFIG_SYS_EBC_PB2CR 0x00000000 #define CONFIG_SYS_EBC_PB3AP 0x00000000 #define CONFIG_SYS_EBC_PB3CR 0x00000000 #define CONFIG_SYS_EBC_PB4AP 0x00000000 #define CONFIG_SYS_EBC_PB4CR 0x00000000 /*----------------------------------------------------------------------- * Definitions for GPIO setup (PPC405EP specific) * * Taken in part from PPCBoot board/icecube/icecube.h */ /* see ./arch/powerpc/cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/start.S */ #define CONFIG_SYS_GPIO0_OSRL 0x55555550 #define CONFIG_SYS_GPIO0_OSRH 0x00000110 #define CONFIG_SYS_GPIO0_ISR1L 0x00000000 #define CONFIG_SYS_GPIO0_ISR1H 0x15555445 #define CONFIG_SYS_GPIO0_TSRL 0x00000000 #define CONFIG_SYS_GPIO0_TSRH 0x00000000 #define CONFIG_SYS_GPIO0_TCR 0xFFFF8097 #define CONFIG_SYS_GPIO0_ODR 0x00000000 #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* ENVIRONMENT VARS */ #define CONFIG_IPADDR 192.168.1.67 #define CONFIG_SERVERIP 192.168.1.50 #define CONFIG_GATEWAYIP 192.168.1.1 #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_LOADADDR 300000 #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #endif /* __CONFIG_H */