/* * (C) Copyright 2000 * Murray Jensen * * (C) Copyright 2000 * Sysgo Real-Time Solutions, GmbH * Marius Groeger * * (C) Copyright 2001 * Advent Networks, Inc. * Jay Monkman * * Configuation settings for the WindRiver PPMC8260 board. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #ifndef __CONFIG_H #define __CONFIG_H /***************************************************************************** * * These settings must match the way _your_ board is set up * *****************************************************************************/ /* What is the oscillator's (UX2) frequency in Hz? */ #define CONFIG_8260_CLKIN (66 * 1000 * 1000) /*----------------------------------------------------------------------- * MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual *----------------------------------------------------------------------- * What should MODCK_H be? It is dependent on the oscillator * frequency, MODCK[1-3], and desired CPM and core frequencies. * Here are some example values (all frequencies are in MHz): * * MODCK_H MODCK[1-3] Osc CPM Core S2-6 S2-7 S2-8 * ------- ---------- --- --- ---- ----- ----- ----- * 0x2 0x2 33 133 133 Close Open Close * 0x2 0x3 33 133 166 Close Open Open * 0x2 0x4 33 133 200 Open Close Close * 0x2 0x5 33 133 233 Open Close Open * 0x2 0x6 33 133 266 Open Open Close * * 0x5 0x5 66 133 133 Open Close Open * 0x5 0x6 66 133 166 Open Open Close * 0x5 0x7 66 133 200 Open Open Open * 0x6 0x0 66 133 233 Close Close Close * 0x6 0x1 66 133 266 Close Close Open * 0x6 0x2 66 133 300 Close Open Close */ #define CFG_PPMC_MODCK_H 0x05 /* Define this if you want to boot from 0x00000100. If you don't define * this, you will need to program the bootloader to 0xfff00000, and * get the hardware reset config words at 0xfe000000. The simplest * way to do that is to program the bootloader at both addresses. * It is suggested that you just let U-Boot live at 0x00000000. */ #define CFG_PPMC_BOOT_LOW 1 /* What should the base address of the main FLASH be and how big is * it (in MBytes)? This must contain TEXT_BASE from board/ppmc8260/config.mk * The main FLASH is whichever is connected to *CS0. U-Boot expects * this to be the SIMM. */ #define CFG_FLASH0_BASE 0xFE000000 #define CFG_FLASH0_SIZE 16 /* What should be the base address of the first SDRAM DIMM and how big is * it (in Mbytes)? */ #define CFG_SDRAM0_BASE 0x00000000 #define CFG_SDRAM0_SIZE 128 /* What should be the base address of the second SDRAM DIMM and how big is * it (in Mbytes)? */ #define CFG_SDRAM1_BASE 0x08000000 #define CFG_SDRAM1_SIZE 128 /* What should be the base address of the on board SDRAM and how big is * it (in Mbytes)? */ #define CFG_SDRAM2_BASE 0x38000000 #define CFG_SDRAM2_SIZE 16 /* What should be the base address of the MAILBOX and how big is it * (in Bytes) * The eeprom lives at CFG_MAILBOX_BASE + 0x80000000 */ #define CFG_MAILBOX_BASE 0x32000000 #define CFG_MAILBOX_SIZE 8192 /* What is the base address of the I/O select lines and how big is it * (In Mbytes)? */ #define CFG_IOSELECT_BASE 0xE0000000 #define CFG_IOSELECT_SIZE 32 /* What should be the base address of the LEDs and switch S0? * If you don't want them enabled, don't define this. */ #define CFG_LED_BASE 0xF1000000 /* * PPMC8260 with 256 16 MB DIMM: * * 0x0000 0000 Exception Vector code, 8k * : * 0x0000 1FFF * 0x0000 2000 Free for Application Use * : * : * * : * : * 0x0FF5 FF30 Monitor Stack (Growing downward) * Monitor Stack Buffer (0x80) * 0x0FF5 FFB0 Board Info Data * 0x0FF6 0000 Malloc Arena * : CFG_ENV_SECT_SIZE, 256k * : CFG_MALLOC_LEN, 128k * 0x0FFC 0000 RAM Copy of Monitor Code * : CFG_MONITOR_LEN, 256k * 0x0FFF FFFF [End of RAM], CFG_SDRAM_SIZE - 1 */ /* * select serial console configuration * * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 * for SCC). * * if CONFIG_CONS_NONE is defined, then the serial console routines must * defined elsewhere. * The console can be on SMC1 or SMC2 */ #define CONFIG_CONS_ON_SMC 1 /* define if console on SMC */ #undef CONFIG_CONS_ON_SCC /* define if console on SCC */ #undef CONFIG_CONS_NONE /* define if console on neither */ #define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ /* * select ethernet configuration * * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 * for FCC) * * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. */ #undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ #define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ #undef CONFIG_ETHER_NONE /* define if ethernet on neither */ #define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ #define CONFIG_MII /* MII PHY management */ #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ /* * Port pins used for bit-banged MII communictions (if applicable). */ #define MDIO_PORT 2 /* Port C */ #define MDIO_ACTIVE (iop->pdir |= 0x00400000) #define MDIO_TRISTATE (iop->pdir &= ~0x00400000) #define MDIO_READ ((iop->pdat & 0x00400000) != 0) #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ else iop->pdat &= ~0x00400000 #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ else iop->pdat &= ~0x00200000 #define MIIDELAY udelay(1) /* Define this to reserve an entire FLASH sector (256 KB) for * environment variables. Otherwise, the environment will be * put in the same sector as U-Boot, and changing variables * will erase U-Boot temporarily */ #define CFG_ENV_IN_OWN_SECT 1 /* Define to allow the user to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE /* What should the console's baud rate be? */ #define CONFIG_BAUDRATE 9600 /* Ethernet MAC address */ #define CONFIG_ETHADDR 00:a0:1e:90:2b:00 /* Define this to set the last octet of the ethernet address * from the DS0-DS7 switch and light the leds with the result * The DS0-DS7 switch and the leds are backwards with respect * to each other. DS7 is on the board edge side of both the * led strip and the DS0-DS7 switch. */ #define CONFIG_MISC_INIT_R /* Set to a positive value to delay for running BOOTCOMMAND */ #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #if 0 /* Be selective on what keys can delay or stop the autoboot process * To stop use: " " */ # define CONFIG_AUTOBOOT_KEYED # define CONFIG_AUTOBOOT_PROMPT \ "Autobooting in %d seconds, press \" \" to stop\n", bootdelay # define CONFIG_AUTOBOOT_STOP_STR " " # undef CONFIG_AUTOBOOT_DELAY_STR # define DEBUG_BOOTKEYS 0 #endif /* Define a command string that is automatically executed when no character * is read on the console interface withing "Boot Delay" after reset. */ #undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */ #define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */ #ifdef CONFIG_BOOT_ROOT_INITRD #define CONFIG_BOOTCOMMAND \ "version;" \ "echo;" \ "bootp;" \ "setenv bootargs root=/dev/ram0 rw " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ "bootm" #endif /* CONFIG_BOOT_ROOT_INITRD */ #ifdef CONFIG_BOOT_ROOT_NFS #define CONFIG_BOOTCOMMAND \ "version;" \ "echo;" \ "bootp;" \ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ "bootm" #endif /* CONFIG_BOOT_ROOT_NFS */ /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_DNS /* undef this to save memory */ #define CFG_LONGHELP /* Monitor Command Prompt */ #define CFG_PROMPT "=> " /* * Command line configuration. */ #include #define CONFIG_CMD_ELF #define CONFIG_CMD_ASKENV #define CONFIG_CMD_REGINFO #define CONFIG_CMD_MEMTEST #define CONFIG_CMD_MII #define CONFIG_CMD_IMMAP #undef CONFIG_CMD_KGDB /* Where do the internal registers live? */ #define CFG_IMMR 0xf0000000 /***************************************************************************** * * You should not have to modify any of the following settings * *****************************************************************************/ #define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ #define CONFIG_PPMC8260 1 /* on an Wind River PPMC8260 Board */ #define CONFIG_CPM2 1 /* Has a CPM2 */ /* * Miscellaneous configurable options */ #if defined(CONFIG_CMD_KGDB) # define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else # define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif /* Print Buffer Size */ #define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT)+16) #define CFG_MAXARGS 32 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_LOAD_ADDR 0x140000 /* default load address */ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CFG_MEMTEST_START 0x2000 /* memtest works from the end of */ /* the exception vector table */ /* to the end of the DRAM */ /* less monitor and malloc area */ #define CFG_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */ #define CFG_MEM_END_USAGE ( CFG_MONITOR_LEN \ + CFG_MALLOC_LEN \ + CFG_ENV_SECT_SIZE \ + CFG_STACK_USAGE ) #define CFG_MEMTEST_END ( CFG_SDRAM_SIZE * 1024 * 1024 \ - CFG_MEM_END_USAGE ) /* valid baudrates */ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ #if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1) /* * Attention: This is board specific * - RX clk is CLK11 * - TX clk is CLK12 */ #define CFG_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 |\ CMXSCR_TS1CS_CLK12) #elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) /* * Attention: this is board-specific * - Rx-CLK is CLK13 * - Tx-CLK is CLK14 * - Select bus for bd/buffers (see 28-13) * - Enable Full Duplex in FSMR */ #define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) #define CFG_CPMFCR_RAMTYPE 0 #define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) #endif /* CONFIG_ETHER_INDEX */ #define CFG_FLASH_BASE CFG_FLASH0_BASE #define CFG_FLASH_SIZE CFG_FLASH0_SIZE #define CFG_SDRAM_BASE CFG_SDRAM0_BASE #define CFG_SDRAM_SIZE (CFG_SDRAM0_SIZE + CFG_SDRAM1_SIZE) /*----------------------------------------------------------------------- * Hard Reset Configuration Words */ #if defined(CFG_PPMC_BOOT_LOW) # define CFG_PPMC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) #else # define CFG_PPMC_HRCW_BOOT_FLAGS (0) #endif /* defined(CFG_PPMC_BOOT_LOW) */ /* get the HRCW ISB field from CFG_IMMR */ #define CFG_PPMC_HRCW_IMMR ( ((CFG_IMMR & 0x10000000) >> 10) | \ ((CFG_IMMR & 0x01000000) >> 7) | \ ((CFG_IMMR & 0x00100000) >> 4) ) #define CFG_HRCW_MASTER ( HRCW_EBM | \ HRCW_BPS11 | \ HRCW_L2CPC10 | \ HRCW_DPPC00 | \ CFG_PPMC_HRCW_IMMR | \ HRCW_MMR00 | \ HRCW_LBPC00 | \ HRCW_APPC10 | \ HRCW_CS10PC00 | \ (CFG_PPMC_MODCK_H & HRCW_MODCK_H1111) | \ CFG_PPMC_HRCW_BOOT_FLAGS ) /* no slaves */ #define CFG_HRCW_SLAVE1 0 #define CFG_HRCW_SLAVE2 0 #define CFG_HRCW_SLAVE3 0 #define CFG_HRCW_SLAVE4 0 #define CFG_HRCW_SLAVE5 0 #define CFG_HRCW_SLAVE6 0 #define CFG_HRCW_SLAVE7 0 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CFG_INIT_RAM_ADDR CFG_IMMR #define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ #define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CFG_SDRAM_BASE _must_ start at 0 * Note also that the logic that sets CFG_RAMBOOT is platform dependent. */ #define CFG_MONITOR_BASE CFG_FLASH0_BASE #ifndef CFG_MONITOR_BASE #define CFG_MONITOR_BASE 0x0ff80000 #endif #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) # define CFG_RAMBOOT #endif #define CFG_MONITOR_LEN (256 << 10) /* Reserve 374 kB for Monitor */ #define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH and environment organization */ #define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ #define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_FLASH_INCREMENT 0 /* there is only one bank */ #define CFG_FLASH_PROTECTION 1 /* use hardware protection */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #ifndef CFG_RAMBOOT # define CONFIG_ENV_IS_IN_FLASH 1 # ifdef CFG_ENV_IN_OWN_SECT # define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) # define CFG_ENV_SECT_SIZE 0x40000 # else # define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CFG_ENV_SECT_SIZE) # define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ # define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sect real size */ # endif /* CFG_ENV_IN_OWN_SECT */ #else # define CONFIG_ENV_IS_IN_FLASH 1 # define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x40000) #define CFG_ENV_SIZE 0x1000 # define CFG_ENV_SECT_SIZE 0x40000 #endif /* CFG_RAMBOOT */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */ #if defined(CONFIG_CMD_KGDB) # define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * HIDx - Hardware Implementation-dependent Registers 2-11 *----------------------------------------------------------------------- * HID0 also contains cache control - initially enable both caches and * invalidate contents, then the final state leaves only the instruction * cache enabled. Note that Power-On and Hard reset invalidate the caches, * but Soft reset does not. * * HID1 has only read-only information - nothing to set. */ #define CFG_HID0_INIT (HID0_ICE |\ HID0_DCE |\ HID0_ICFI |\ HID0_DCI |\ HID0_IFEM |\ HID0_ABE) #define CFG_HID0_FINAL (HID0_ICE |\ HID0_IFEM |\ HID0_ABE |\ HID0_EMCP) #define CFG_HID2 0 /*----------------------------------------------------------------------- * RMR - Reset Mode Register *----------------------------------------------------------------------- */ #define CFG_RMR 0 /*----------------------------------------------------------------------- * BCR - Bus Configuration 4-25 *----------------------------------------------------------------------- */ #define CFG_BCR (BCR_EBM |\ 0x30000000) /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 4-31 * Ref Section 4.3.2.6 page 4-31 *----------------------------------------------------------------------- */ #define CFG_SIUMCR (SIUMCR_ESE |\ SIUMCR_DPPC00 |\ SIUMCR_L2CPC10 |\ SIUMCR_LBPC00 |\ SIUMCR_APPC10 |\ SIUMCR_CS10PC00 |\ SIUMCR_BCTLC00 |\ SIUMCR_MMR00) /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable */ #define CFG_SYPCR (SYPCR_SWTC |\ SYPCR_BMT |\ SYPCR_PBME |\ SYPCR_LBME |\ SYPCR_SWRI |\ SYPCR_SWP) /*----------------------------------------------------------------------- * TMCNTSC - Time Counter Status and Control 4-40 *----------------------------------------------------------------------- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, * and enable Time Counter */ #define CFG_TMCNTSC (TMCNTSC_SEC |\ TMCNTSC_ALR |\ TMCNTSC_TCF |\ TMCNTSC_TCE) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 4-42 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable * Periodic timer */ #define CFG_PISCR (PISCR_PS |\ PISCR_PTF |\ PISCR_PTE) /*----------------------------------------------------------------------- * SCCR - System Clock Control 9-8 *----------------------------------------------------------------------- */ #define CFG_SCCR 0 /*----------------------------------------------------------------------- * RCCR - RISC Controller Configuration 13-7 *----------------------------------------------------------------------- */ #define CFG_RCCR 0 /* * Initialize Memory Controller: * * Bank Bus Machine PortSz Device * ---- --- ------- ------ ------ * 0 60x GPCM 32 bit FLASH (SIMM - 32MB) * * 1 unused * 2 60x SDRAM 64 bit SDRAM (DIMM - 128MB) * 3 60x SDRAM 64 bit SDRAM (DIMM - 128MB) * 4 Local SDRAM 32 bit SDRAM (on board - 16MB) * 5 60x GPCM 8 bit Mailbox/EEPROM (8KB) * 6 60x GPCM 8 bit FLASH (on board - 2MB) * * 7 60x GPCM 8 bit LEDs, switches * * (*) This configuration requires the PPMC8260 be configured * so that *CS0 goes to the FLASH SIMM, and *CS6 goes to * the on board FLASH. In other words, JP24 should have * pins 1 and 2 jumpered and pins 3 and 4 jumpered. * */ /*----------------------------------------------------------------------- * BR0,BR1 - Base Register * Ref: Section 10.3.1 on page 10-14 * OR0,OR1 - Option Register * Ref: Section 10.3.2 on page 10-18 *----------------------------------------------------------------------- */ /* Bank 0,1 - FLASH SIMM * * This expects the FLASH SIMM to be connected to *CS0 * It consists of 4 AM29F080B parts. * * Note: For the 4 MB SIMM, *CS1 is unused. */ /* BR0 is configured as follows: * * - Base address of 0xFE000000 * - 32 bit port size * - Data errors checking is disabled * - Read and write access * - GPCM 60x bus * - Access are handled by the memory controller according to MSEL * - Not used for atomic operations * - No data pipelining is done * - Valid */ #define CFG_BR0_PRELIM ((CFG_FLASH0_BASE & BRx_BA_MSK) |\ BRx_PS_32 |\ BRx_MS_GPCM_P |\ BRx_V) /* OR0 is configured as follows: * * - 32 MB * - *BCTL0 is asserted upon access to the current memory bank * - *CW / *WE are negated a quarter of a clock earlier * - *CS is output at the same time as the address lines * - Uses a clock cycle length of 5 * - *PSDVAL is generated internally by the memory controller * unless *GTA is asserted earlier externally. * - Relaxed timing is generated by the GPCM for accesses * initiated to this memory region. * - One idle clock is inserted between a read access from the * current bank and the next access. */ #define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH0_SIZE) |\ ORxG_CSNT |\ ORxG_ACS_DIV1 |\ ORxG_SCY_5_CLK |\ ORxG_TRLX |\ ORxG_EHTR) /*----------------------------------------------------------------------- * BR2,BR3 - Base Register * Ref: Section 10.3.1 on page 10-14 * OR2,OR3 - Option Register * Ref: Section 10.3.2 on page 10-16 *----------------------------------------------------------------------- */ /* * Bank 2,3 - 128 MB SDRAM DIMM */ /* With a 128 MB DIMM, the BR2 is configured as follows: * * - Base address of 0x00000000/0x08000000 * - 64 bit port size (60x bus only) * - Data errors checking is disabled * - Read and write access * - SDRAM 60x bus * - Access are handled by the memory controller according to MSEL * - Not used for atomic operations * - No data pipelining is done * - Valid */ #define CFG_BR2_PRELIM ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\ BRx_PS_64 |\ BRx_MS_SDRAM_P |\ BRx_V) #define CFG_BR3_PRELIM ((CFG_SDRAM1_BASE & BRx_BA_MSK) |\ BRx_PS_64 |\ BRx_MS_SDRAM_P |\ BRx_V) /* With a 128 MB DIMM, the OR2 is configured as follows: * * - 128 MB * - 4 internal banks per device * - Row start address bit is A8 with PSDMR[PBI] = 0 * - 13 row address lines * - Back-to-back page mode * - Internal bank interleaving within save device enabled */ #define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\ ORxS_BPD_4 |\ ORxS_ROWST_PBI0_A7 |\ ORxS_NUMR_13) #define CFG_OR3_PRELIM (MEG_TO_AM(CFG_SDRAM1_SIZE) |\ ORxS_BPD_4 |\ ORxS_ROWST_PBI0_A7 |\ ORxS_NUMR_13) /*----------------------------------------------------------------------- * PSDMR - 60x Bus SDRAM Mode Register * Ref: Section 10.3.3 on page 10-21 *----------------------------------------------------------------------- */ /* With a 128 MB DIMM, the PSDMR is configured as follows: * * - Page Based Interleaving, * - Refresh Enable, * - Normal Operation * - Address Multiplexing where A5 is output on A14 pin * (A6 on A15, and so on), * - use address pins A13-A15 as bank select, * - A9 is output on SDA10 during an ACTIVATE command, * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks, * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command * is 3 clocks, * - earliest timing for READ/WRITE command after ACTIVATE command is * 2 clocks, * - earliest timing for PRECHARGE after last data was read is 1 clock, * - earliest timing for PRECHARGE after last data was written is 1 clock, * - External Address Multiplexing enabled * - CAS Latency is 2. */ #define CFG_PSDMR (PSDMR_RFEN |\ PSDMR_SDAM_A14_IS_A5 |\ PSDMR_BSMA_A13_A15 |\ PSDMR_SDA10_PBI0_A9 |\ PSDMR_RFRC_7_CLK |\ PSDMR_PRETOACT_3W |\ PSDMR_ACTTORW_2W |\ PSDMR_LDOTOPRE_1C |\ PSDMR_WRC_1C |\ PSDMR_EAMUX |\ PSDMR_CL_2) #define CFG_PSRT 0x0e #define CFG_MPTPR MPTPR_PTP_DIV32 /*----------------------------------------------------------------------- * BR4 - Base Register * Ref: Section 10.3.1 on page 10-14 * OR4 - Option Register * Ref: Section 10.3.2 on page 10-16 *----------------------------------------------------------------------- */ /* * Bank 4 - On board SDRAM * */ /* With 16 MB of onboard SDRAM BR4 is configured as follows * * - Base address 0x38000000 * - 32 bit port size * - Data error checking disabled * - Read/Write access * - SDRAM local bus * - Not used for atomic operations * - No data pipelining is done * - Valid * */ #define CFG_BR4_PRELIM ((CFG_SDRAM2_BASE & BRx_BA_MSK) |\ BRx_PS_32 |\ BRx_DECC_NONE |\ BRx_MS_SDRAM_L |\ BRx_V) /* * With 16MB SDRAM, OR4 is configured as follows * - 4 internal banks per device * - Row start address bit is A10 with LSDMR[PBI] = 0 * - 12 row address lines * - Back-to-back page mode * - Internal bank interleaving within save device enabled */ #define CFG_OR4_PRELIM (MEG_TO_AM(CFG_SDRAM2_SIZE) |\ ORxS_BPD_4 |\ ORxS_ROWST_PBI0_A10 |\ ORxS_NUMR_12) /*----------------------------------------------------------------------- * LSDMR - Local Bus SDRAM Mode Register * Ref: Section 10.3.4 on page 10-24 *----------------------------------------------------------------------- */ /* With a 16 MB onboard SDRAM, the LSDMR is configured as follows: * * - Page Based Interleaving, * - Refresh Enable, * - Normal Operation * - Address Multiplexing where A5 is output on A13 pin * (A6 on A15, and so on), * - use address pins A15-A17 as bank select, * - A11 is output on SDA10 during an ACTIVATE command, * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks, * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command * is 2 clocks, * - earliest timing for READ/WRITE command after ACTIVATE command is * 2 clocks, * - SDRAM burst length is 8 * - earliest timing for PRECHARGE after last data was read is 1 clock, * - earliest timing for PRECHARGE after last data was written is 1 clock, * - External Address Multiplexing disabled * - CAS Latency is 2. */ #define CFG_LSDMR (PSDMR_RFEN |\ PSDMR_SDAM_A13_IS_A5 |\ PSDMR_BSMA_A15_A17 |\ PSDMR_SDA10_PBI0_A11 |\ PSDMR_RFRC_7_CLK |\ PSDMR_PRETOACT_2W |\ PSDMR_ACTTORW_2W |\ PSDMR_BL |\ PSDMR_LDOTOPRE_1C |\ PSDMR_WRC_1C |\ PSDMR_CL_2) #define CFG_LSRT 0x0e /*----------------------------------------------------------------------- * BR5 - Base Register * Ref: Section 10.3.1 on page 10-14 * OR5 - Option Register * Ref: Section 10.3.2 on page 10-16 *----------------------------------------------------------------------- */ /* * Bank 5 EEProm and Mailbox * * The EEPROM and mailbox live on the same chip select. * the eeprom is selected if the MSb of the address is set and the mailbox is * selected if the MSb of the address is clear. * */ /* BR5 is configured as follows: * * - Base address of 0x32000000/0xF2000000 * - 8 bit * - Data error checking disabled * - Read/Write access * - GPCM 60x Bus * - SDRAM local bus * - No data pipelining is done * - Valid */ #define CFG_BR5_PRELIM ((CFG_MAILBOX_BASE & BRx_BA_MSK) |\ BRx_PS_8 |\ BRx_DECC_NONE |\ BRx_MS_GPCM_P |\ BRx_V) /* OR5 is configured as follows * - buffer control enabled * - chip select negated normally * - CS output 1/2 clock after address * - 15 wait states * - *PSDVAL is generated internally by the memory controller * unless *GTA is asserted earlier externally. * - Relaxed timing is generated by the GPCM for accesses * initiated to this memory region. * - One idle clock is inserted between a read access from the * current bank and the next access. */ #define CFG_OR5_PRELIM ((P2SZ_TO_AM(CFG_MAILBOX_SIZE) & ~0x80000000) |\ ORxG_ACS_DIV2 |\ ORxG_SCY_15_CLK |\ ORxG_TRLX |\ ORxG_EHTR) /*----------------------------------------------------------------------- * BR6 - Base Register * Ref: Section 10.3.1 on page 10-14 * OR6 - Option Register * Ref: Section 10.3.2 on page 10-18 *----------------------------------------------------------------------- */ /* Bank 6 - I/O select * */ /* BR6 is configured as follows: * * - Base address of 0xE0000000 * - 16 bit port size * - Data errors checking is disabled * - Read and write access * - GPCM 60x bus * - Access are handled by the memory controller according to MSEL * - Not used for atomic operations * - No data pipelining is done * - Valid */ #define CFG_BR6_PRELIM ((CFG_IOSELECT_BASE & BRx_BA_MSK) |\ BRx_PS_16 |\ BRx_MS_GPCM_P |\ BRx_V) /* OR6 is configured as follows * - buffer control enabled * - chip select negated normally * - CS output 1/2 clock after address * - 15 wait states * - *PSDVAL is generated internally by the memory controller * unless *GTA is asserted earlier externally. * - Relaxed timing is generated by the GPCM for accesses * initiated to this memory region. * - One idle clock is inserted between a read access from the * current bank and the next access. */ #define CFG_OR6_PRELIM (MEG_TO_AM(CFG_IOSELECT_SIZE) |\ ORxG_ACS_DIV2 |\ ORxG_SCY_15_CLK |\ ORxG_TRLX |\ ORxG_EHTR) /*----------------------------------------------------------------------- * BR7 - Base Register * Ref: Section 10.3.1 on page 10-14 * OR7 - Option Register * Ref: Section 10.3.2 on page 10-18 *----------------------------------------------------------------------- */ /* Bank 7 - LEDs and switches * * LEDs are at 0x00001 (write only) * switches are at 0x00001 (read only) */ #ifdef CFG_LED_BASE /* BR7 is configured as follows: * * - Base address of 0xA0000000 * - 8 bit port size * - Data errors checking is disabled * - Read and write access * - GPCM 60x bus * - Access are handled by the memory controller according to MSEL * - Not used for atomic operations * - No data pipelining is done * - Valid */ #define CFG_BR7_PRELIM ((CFG_LED_BASE & BRx_BA_MSK) |\ BRx_PS_8 |\ BRx_DECC_NONE |\ BRx_MS_GPCM_P |\ BRx_V) /* OR7 is configured as follows: * * - 1 byte * - *BCTL0 is asserted upon access to the current memory bank * - *CW / *WE are negated a quarter of a clock earlier * - *CS is output at the same time as the address lines * - Uses a clock cycle length of 15 * - *PSDVAL is generated internally by the memory controller * unless *GTA is asserted earlier externally. * - Relaxed timing is generated by the GPCM for accesses * initiated to this memory region. * - One idle clock is inserted between a read access from the * current bank and the next access. */ #define CFG_OR7_PRELIM (ORxG_AM_MSK |\ ORxG_CSNT |\ ORxG_ACS_DIV1 |\ ORxG_SCY_15_CLK |\ ORxG_TRLX |\ ORxG_EHTR) #endif /* CFG_LED_BASE */ /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #endif /* __CONFIG_H */