/* * Copyright (C) 2012 Freescale Semiconductor, Inc. * * Configuration settings for the MX6DL SabreSD Freescale board. * The board is configured with SOLO and 32-bit DDR bus-width. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #ifndef __CONFIG_H #define __CONFIG_H #include /* High Level Configuration Options */ #define CONFIG_ARMV7 /* This is armv7 Cortex-A9 CPU core */ #define CONFIG_MXC #define CONFIG_MX6DL #define CONFIG_MX6DL_DDR3 #define CONFIG_MX6DL_SABRESD #define CONFIG_DDR_32BIT /* for DDR 32bit */ #define CONFIG_FLASH_HEADER #define CONFIG_FLASH_HEADER_OFFSET 0x400 #define CONFIG_MX6_CLK32 32768 #define CONFIG_SKIP_RELOCATE_UBOOT #define CONFIG_ARCH_CPU_INIT #undef CONFIG_ARCH_MMU /* disable MMU first */ #define CONFIG_L2_OFF /* disable L2 cache first*/ #define CONFIG_MX6_HCLK_FREQ 24000000 #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO #define CONFIG_SYS_64BIT_VSPRINTF #define BOARD_LATE_INIT #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ #define CONFIG_SERIAL_TAG #define CONFIG_REVISION_TAG #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG #define CONFIG_MXC_GPIO /* * Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (2 * 1024 * 1024) /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* * Hardware drivers */ #define CONFIG_MXC_UART #define CONFIG_UART_BASE_ADDR UART1_BASE_ADDR /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_CONS_INDEX 1 #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200} /*********************************************************** * Command definition ***********************************************************/ #include #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_MII #define CONFIG_CMD_NET #define CONFIG_NET_RETRY_COUNT 100 #define CONFIG_NET_MULTI 1 #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_DNS #define CONFIG_CMD_SPI #define CONFIG_CMD_I2C #define CONFIG_CMD_IMXOTP /* Enable below configure when supporting nand */ #define CONFIG_CMD_SF #define CONFIG_CMD_MMC #define CONFIG_CMD_ENV #define CONFIG_CMD_REGUL #define CONFIG_CMD_CLOCK #define CONFIG_REF_CLK_FREQ CONFIG_MX6_HCLK_FREQ #undef CONFIG_CMD_IMLS #define CONFIG_CMD_IMX_DOWNLOAD_MODE #define CONFIG_BOOTDELAY 3 #define CONFIG_PRIME "FEC0" #define CONFIG_LOADADDR 0x10800000 /* loadaddr env var */ #define CONFIG_RD_LOADADDR (CONFIG_LOADADDR + 0x300000) #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "ethprime=FEC0\0" \ "uboot=u-boot.bin\0" \ "kernel=uImage\0" \ "nfsroot=/opt/eldk/arm\0" \ "bootargs_base=setenv bootargs console=ttymxc0,115200 nosmp\0" \ "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ "bootcmd_net=run bootargs_base bootargs_nfs; " \ "tftpboot ${loadaddr} ${kernel}; bootm\0" \ "bootargs_mmc=setenv bootargs ${bootargs} ip=dhcp " \ "root=/dev/mmcblk0p1 rootwait\0" \ "bootcmd_mmc=run bootargs_base bootargs_mmc; " \ "mmc dev 3; " \ "mmc read ${loadaddr} 0x800 0x2000; bootm\0" \ "bootcmd=run bootcmd_net\0" \ #define CONFIG_ARP_TIMEOUT 200UL /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "MX6SDL SABRESD U-Boot > " #define CONFIG_AUTO_COMPLETE #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x10010000 #undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */ #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR #define CONFIG_SYS_HZ 1000 #define CONFIG_CMDLINE_EDITING #define CONFIG_FEC0_IOBASE ENET_BASE_ADDR #define CONFIG_FEC0_PINMUX -1 #define CONFIG_FEC0_MIIBASE -1 #define CONFIG_GET_FEC_MAC_ADDR_FROM_IIM #define CONFIG_MXC_FEC #define CONFIG_FEC0_PHY_ADDR 1 #define CONFIG_ETH_PRIME #define CONFIG_RMII #define CONFIG_CMD_MII #define CONFIG_CMD_DHCP #define CONFIG_CMD_PING #define CONFIG_IPADDR 192.168.1.103 #define CONFIG_SERVERIP 192.168.1.101 #define CONFIG_NETMASK 255.255.255.0 /* * OCOTP Configs */ #ifdef CONFIG_CMD_IMXOTP #define CONFIG_IMX_OTP #define IMX_OTP_BASE OCOTP_BASE_ADDR #define IMX_OTP_ADDR_MAX 0x7F #define IMX_OTP_DATA_ERROR_VAL 0xBADABADA #endif /* * I2C Configs */ #ifdef CONFIG_CMD_I2C #define CONFIG_HARD_I2C #define CONFIG_I2C_MXC 1 #define CONFIG_SYS_I2C_PORT I2C2_BASE_ADDR #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_SYS_I2C_SLAVE 0x8 #define CONFIG_MX6_INTER_LDO_BYPASS 0 #endif /* * SPI Configs */ #ifdef CONFIG_CMD_SF #define CONFIG_FSL_SF #define CONFIG_SPI_FLASH_IMX_M25PXX #define CONFIG_SPI_FLASH_CS 0 #define CONFIG_IMX_ECSPI #define IMX_CSPI_VER_2_3 1 #define MAX_SPI_BYTES (64 * 4) #endif /* Regulator Configs */ #ifdef CONFIG_CMD_REGUL #define CONFIG_ANATOP_REGULATOR #define CONFIG_CORE_REGULATOR_NAME "vdd1p1" #define CONFIG_PERIPH_REGULATOR_NAME "vdd1p1" #endif /* * MMC Configs */ #ifdef CONFIG_CMD_MMC #define CONFIG_MMC #define CONFIG_GENERIC_MMC #define CONFIG_IMX_MMC #define CONFIG_SYS_FSL_USDHC_NUM 4 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 #define CONFIG_SYS_MMC_ENV_DEV 2 #define CONFIG_DOS_PARTITION #define CONFIG_CMD_FAT #define CONFIG_CMD_EXT2 /* detect whether SD1, 2, 3, or 4 is boot device */ #define CONFIG_DYNAMIC_MMC_DEVNO /* SD3 and SD4 are 8 bit */ #define CONFIG_MMC_8BIT_PORTS 0xC /* Setup target delay in DDR mode for each SD port */ #define CONFIG_GET_DDR_TARGET_DELAY #endif /* * GPMI Nand Configs */ /* #define CONFIG_CMD_NAND */ #ifdef CONFIG_CMD_NAND #define CONFIG_NAND_GPMI #define CONFIG_GPMI_NFC_SWAP_BLOCK_MARK #define CONFIG_GPMI_NFC_V2 #define CONFIG_GPMI_REG_BASE GPMI_BASE_ADDR #define CONFIG_BCH_REG_BASE BCH_BASE_ADDR #define NAND_MAX_CHIPS 8 #define CONFIG_SYS_NAND_BASE 0x40000000 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* NAND is the unique module invoke APBH-DMA */ #define CONFIG_APBH_DMA #define CONFIG_APBH_DMA_V2 #define CONFIG_MXS_DMA_REG_BASE ABPHDMA_BASE_ADDR #endif /*----------------------------------------------------------------------- * Stack sizes * * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ /*----------------------------------------------------------------------- * Physical Memory Map */ #define CONFIG_NR_DRAM_BANKS 1 #define PHYS_SDRAM_1 CSD0_DDR_BASE_ADDR #define PHYS_SDRAM_1_SIZE (512 * 1024 * 1024) #define iomem_valid_addr(addr, size) \ (addr >= PHYS_SDRAM_1 && addr <= (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE)) /*----------------------------------------------------------------------- * FLASH and environment organization */ #define CONFIG_SYS_NO_FLASH /* Monitor at beginning of flash */ #define CONFIG_FSL_ENV_IN_MMC /* #define CONFIG_FSL_ENV_IN_NAND */ #define CONFIG_ENV_SECT_SIZE (8 * 1024) #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE #if defined(CONFIG_FSL_ENV_IN_NAND) #define CONFIG_ENV_IS_IN_NAND 1 #define CONFIG_ENV_OFFSET 0x100000 #elif defined(CONFIG_FSL_ENV_IN_MMC) #define CONFIG_ENV_IS_IN_MMC 1 #define CONFIG_ENV_OFFSET (768 * 1024) #elif defined(CONFIG_FSL_ENV_IN_SF) #define CONFIG_ENV_IS_IN_SPI_FLASH 1 #define CONFIG_ENV_SPI_CS 1 #define CONFIG_ENV_OFFSET (768 * 1024) #else #define CONFIG_ENV_IS_NOWHERE 1 #endif /* #define CONFIG_SPLASH_SCREEN */ /* #define CONFIG_MXC_EPDC */ /* * SPLASH SCREEN Configs */ #define CONFIG_SPLASH_SCREEN #ifdef CONFIG_SPLASH_SCREEN /* * Framebuffer and LCD */ #define CONFIG_LCD #define CONFIG_FB_BASE (TEXT_BASE + 0x300000) #define CONFIG_SYS_CONSOLE_IS_IN_ENV #ifdef CONFIG_MXC_EPDC #undef LCD_TEST_PATTERN /* #define CONFIG_SPLASH_IS_IN_MMC 1 */ #define LCD_BPP LCD_MONOCHROME /* #define CONFIG_SPLASH_SCREEN_ALIGN 1 */ #define CONFIG_MXC_EPDC 1 #define CONFIG_WORKING_BUF_ADDR (TEXT_BASE + 0x100000) #define CONFIG_WAVEFORM_BUF_ADDR (TEXT_BASE + 0x200000) #define CONFIG_WAVEFORM_FILE_OFFSET 0x600000 #define CONFIG_WAVEFORM_FILE_SIZE 0xF0A00 #define CONFIG_WAVEFORM_FILE_IN_MMC #ifdef CONFIG_SPLASH_IS_IN_MMC #define CONFIG_SPLASH_IMG_OFFSET 0x4c000 #define CONFIG_SPLASH_IMG_SIZE 0x19000 #endif #else /* !CONFIG_MXC_EPDC */ #define CONFIG_IPU_V3H #define CONFIG_VIDEO_MX5 #define CONFIG_IPU_CLKRATE 260000000 #define CONFIG_SYS_CONSOLE_ENV_OVERWRITE #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE #define LCD_BPP LCD_COLOR16 #define CONFIG_CMD_BMP #define CONFIG_BMP_8BPP #define CONFIG_SPLASH_SCREEN_ALIGN #define CONFIG_SYS_WHITE_ON_BLACK #define CONFIG_IMX_PWM #define IMX_PWM1_BASE PWM1_BASE_ADDR #define IMX_PWM2_BASE PWM2_BASE_ADDR #endif #endif /* CONFIG_SPLASH_SCREEN */ #endif /* __CONFIG_H */