/* * (C) Copyright 2006 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC5200 #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ #define CONFIG_MCC200 1 /* ... on MCC200 board */ #define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33MHz */ #define CONFIG_MISC_INIT_R #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) # define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* * Serial console configuration * * To select console on the one of 8 external UARTs, * define CONFIG_QUART_CONSOLE as 1, 2, 3, or 4 for the first Quad UART, * or as 5, 6, 7, or 8 for the second Quad UART. * COM11, COM12, COM13, COM14 are located on the second Quad UART. * * CONFIG_PSC_CONSOLE must be undefined in this case. */ #ifdef CONFIG_CONSOLE_COM12 #define CONFIG_QUART_CONSOLE 6 /* console is on UARTF of QUART2 */ #else #define CONFIG_QUART_CONSOLE 8 /* console is on UARTH of QUART2 */ #endif /* * To select console on PSC1, define CONFIG_PSC_CONSOLE as 1 * and undefine CONFIG_QUART_CONSOLE. */ /*#define CONFIG_PSC_CONSOLE 1 */ /* console is on PSC1 */ #if defined(CONFIG_QUART_CONSOLE) && defined(CONFIG_PSC_CONSOLE) #error "Select only one console device!" #endif #define CONFIG_BAUDRATE 115200 #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } #define CONFIG_MII 1 #define CONFIG_DOS_PARTITION /* USB */ #define CONFIG_USB_OHCI #define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT #define CONFIG_USB_STORAGE /* * Supported commands */ #define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ ADD_USB_CMD | \ CFG_CMD_BEDBUG | \ CFG_CMD_FAT | \ CFG_CMD_I2C) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include /* * Autobooting */ #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #define CONFIG_PREBOOT "echo;" \ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ "echo" #undef CONFIG_BOOTARGS #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "hostname=mcc200\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "flash_nfs=run nfsargs addip;" \ "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "rootpath=/opt/eldk/ppc_6xx\0" \ "bootfile=/tftpboot/mcc200/uImage\0" \ "baudrate=115200\0" \ "load=tftp 200000 /tftpboot/mcc200/u-boot.bin\0" \ "update=protect off FFF00000 +${filesize};" \ "era FFF00000 +${filesize};" \ "cp.b 200000 FFF00000 ${filesize}\0" \ "serverip=192.168.1.1\0" \ "ipaddr=192.168.133.144\0" \ "netmask=255.255.0.0\0" \ "unlock=yes\0" \ "ethaddr=00:02:44:7D:73:3B\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" #define CFG_HUSH_PARSER 1 /* use "hush" command parser */ #define CFG_PROMPT_HUSH_PS2 "> " /* * IPB Bus clocking configuration. */ #define CFG_IPBSPEED_133 /* define for 133MHz speed */ /* * I2C configuration */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CFG_I2C_MODULE 1 /* Select I2C module #1 or #2 */ #define CFG_I2C_SPEED 100000 /* 100 kHz */ #define CFG_I2C_SLAVE 0x7F /* * Flash configuration (8,16 or 32 MB) * TEXT base always at 0xFFF00000 * ENV_ADDR always at 0xFFF40000 * FLASH_BASE at 0xFC000000 for 64 MB (only 32MB are supported, not enough addr lines!!!) * 0xFE000000 for 32 MB * 0xFF000000 for 16 MB * 0xFF800000 for 8 MB */ #define CFG_FLASH_BASE 0xfc000000 #define CFG_FLASH_SIZE 0x04000000 #define CFG_FLASH_CFI /* The flash is CFI compatible */ #define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CFG_FLASH_PROTECTION 1 /* hardware flash protection */ #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) #define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */ #if TEXT_BASE == CFG_FLASH_BASE #define CFG_LOWBOOT 1 #endif /* * Memory map */ #define CFG_MBAR 0xf0000000 #define CFG_SDRAM_BASE 0x00000000 #define CFG_DEFAULT_MBAR 0x80000000 /* Use SRAM until RAM will be available */ #define CFG_INIT_RAM_ADDR MPC5XXX_SRAM #define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET #define CFG_MONITOR_BASE TEXT_BASE #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) # define CFG_RAMBOOT 1 #endif #define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CFG_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Ethernet configuration */ #define CONFIG_MPC5xxx_FEC 1 /* * Define CONFIG_FEC_10MBIT to force FEC at 10Mb */ /* #define CONFIG_FEC_10MBIT 1 */ #define CONFIG_PHY_ADDR 1 /* * GPIO configuration */ /* 0x10000004 = 32MB SDRAM */ /* 0x90000004 = 64MB SDRAM */ #define CFG_GPS_PORT_CONFIG 0x00000004 /* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_MEMTEST_START 0x00100000 /* memtest works on */ #define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ #define CFG_LOAD_ADDR 0x100000 /* default load address */ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ /* * Various low-level settings */ #define CFG_HID0_INIT HID0_ICE | HID0_ICFI #define CFG_HID0_FINAL HID0_ICE #define CFG_BOOTCS_START CFG_FLASH_BASE #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE #define CFG_BOOTCS_CFG 0x0004fb00 #define CFG_CS0_START CFG_FLASH_BASE #define CFG_CS0_SIZE CFG_FLASH_SIZE /* Quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */ #define CFG_CS2_START 0x80000000 #define CFG_CS2_SIZE 0x00001000 #define CFG_CS2_CFG 0x1d300 /* Second Quad UART @0x80010000 */ #define CFG_CS1_START 0x80010000 #define CFG_CS1_SIZE 0x00001000 #define CFG_CS1_CFG 0x1d300 /* * Select one of quarts as a default * console. If undefined - PSC console * wil be default */ #define CFG_CS_BURST 0x00000000 #define CFG_CS_DEADCYCLE 0x33333333 #define CFG_RESET_ADDRESS 0xff000000 /* * QUART Expanders support */ #if defined(CONFIG_QUART_CONSOLE) /* * We'll use NS16550 chip routines, */ #define CFG_NS16550 1 #define CFG_NS16550_SERIAL 1 #define CONFIG_CONS_INDEX 1 /* * To achieve necessary offset on SC16C554 * A0-A2 (register select) pins with NS16550 * functions (in struct NS16550), REG_SIZE * should be 4, because A0-A2 pins are connected * to DA2-DA4 address bus lines. */ #define CFG_NS16550_REG_SIZE 4 /* * LocalPlus Bus already inited in cpu_init_f(), * so can work with QUART's chip selects. * One of four SC16C554 UARTs is selected with * A3-A4 (DA5-DA6) lines. */ #if (CONFIG_QUART_CONSOLE > 0) && (CONFIG_QUART_CONSOLE < 5) #define CFG_NS16550_COM1 (CFG_CS2_START | (CONFIG_QUART_CONSOLE - 1)<<5) #elif (CONFIG_QUART_CONSOLE > 4) && (CONFIG_QUART_CONSOLE < 9) #define CFG_NS16550_COM1 (CFG_CS1_START | (CONFIG_QUART_CONSOLE - 5)<<5) #elif #error "Wrong QUART expander number." #endif /* * SC16C554 chip's external crystal oscillator frequency * is 7.3728 MHz */ #define CFG_NS16550_CLK 7372800 #endif /* CONFIG_QUART_CONSOLE */ /*----------------------------------------------------------------------- * USB stuff *----------------------------------------------------------------------- */ #define CONFIG_USB_CLOCK 0x0001BBBB #define CONFIG_USB_CONFIG 0x00005000 #endif /* __CONFIG_H */