/* * Copyright (C) 2006 Mihai Georgian * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #ifndef __CONFIG_H #define __CONFIG_H #if 0 #define DEBUG #endif #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ /*----------------------------------------------------------------------- * User configurable settings: * Mandatory settings: * CONFIG_IPADDR_LS - the IP address of the LinkStation * CONFIG_SERVERIP_LS - the address of the server for NFS/TFTP/DHCP/BOOTP * Optional settins: * CONFIG_NCIP_LS - the adress of the computer running net console * if not configured, it will be set to * CONFIG_SERVERIP_LS */ #define CONFIG_IPADDR_LS 192.168.11.150 #define CONFIG_SERVERIP_LS 192.168.11.149 #if !defined(CONFIG_IPADDR_LS) || !defined(CONFIG_SERVERIP_LS) #error Both CONFIG_IPADDR_LS and CONFIG_SERVERIP_LS must be defined #endif #if !defined(CONFIG_NCIP_LS) #define CONFIG_NCIP_LS CONFIG_SERVERIP_LS #endif /*---------------------------------------------------------------------- * DO NOT CHANGE ANYTHING BELOW, UNLESS YOU KNOW WHAT YOU ARE DOING *---------------------------------------------------------------------*/ #define CONFIG_MPC8245 1 #define CONFIG_LINKSTATION 1 /*--------------------------------------- * Supported models * * LinkStation HDLAN /KuroBox Standard (CONFIG_HLAN) * LinkStation old model (CONFIG_LAN) - totally untested * LinkStation HGLAN / KuroBox HG (CONFIG_HGLAN) * * Models not supported yet * TeraStatin (CONFIG_HTGL) */ #if defined(CONFIG_HLAN) || defined(CONFIG_LAN) #define CONFIG_IDENT_STRING " LinkStation / KuroBox" #elif defined(CONFIG_HGLAN) #define CONFIG_IDENT_STRING " LinkStation HG / KuroBox HG" #elif defined(CONFIG_HTGL) #define CONFIG_IDENT_STRING " TeraStation" #else #error No LinkStation model defined #endif #define CONFIG_BOOTDELAY 5 #define CONFIG_ZERO_BOOTDELAY_CHECK #undef CONFIG_BOOT_RETRY_TIME #define CONFIG_AUTOBOOT_KEYED #define CONFIG_AUTOBOOT_PROMPT \ "Boot in %02d seconds ('s' to stop)...", bootdelay #define CONFIG_AUTOBOOT_STOP_STR "s" #define CONFIG_CMD_IDE #define CONFIG_CMD_PCI #define CONFIG_CMD_DHCP #define CONFIG_CMD_PING #define CONFIG_CMD_EXT2 #define CONFIG_BOOTP_MASK CONFIG_BOOTP_ALL #define CONFIG_OF_LIBFDT 1 #define OF_CPU "PowerPC,603e" #define OF_SOC "soc10x@80000000" #define OF_STDOUT_PATH "/soc10x/serial@80004600" /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include /* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) #define CFG_MAXARGS 16 /* Max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_LOAD_ADDR 0x00800000 /* Default load address: 8 MB */ #define CONFIG_BOOTCOMMAND "run bootcmd1" #define CONFIG_BOOTARGS "root=/dev/sda1 console=ttyS1,57600 netconsole=@192.168.1.7/eth0,@192.168.1.1/00:50:BF:A4:59:71 rtc-rs5c372.probe=0,0x32 debug" #define CONFIG_NFSBOOTCOMMAND "bootp;run nfsargs;bootm" #define CFG_CONSOLE_IS_IN_ENV #define XMK_STR(x) #x #define MK_STR(x) XMK_STR(x) #if defined(CONFIG_HLAN) || defined(CONFIG_LAN) #define UBFILE "share/u-boot/u-boot-hd.flash.bin" #elif defined(CONFIG_HGLAN) #define UBFILE "share/u-boot/u-boot-hg.flash.bin" #elif defined(CONFIG_HTGL) #define UBFILE "share/u-boot/u-boot-ht.flash.bin" #else #error No LinkStation model defined #endif #define CONFIG_EXTRA_ENV_SETTINGS \ "autoload=no\0" \ "stdin=nc\0" \ "stdout=nc\0" \ "stderr=nc\0" \ "ipaddr="MK_STR(CONFIG_IPADDR_LS)"\0" \ "netmask=255.255.255.0\0" \ "serverip="MK_STR(CONFIG_SERVERIP_LS)"\0" \ "ncip="MK_STR(CONFIG_NCIP_LS)"\0" \ "netretry=no\0" \ "nc=setenv stdin nc;setenv stdout nc;setenv stderr nc\0" \ "ser=setenv stdin serial;setenv stdout serial;setenv stderr serial\0" \ "ldaddr=800000\0" \ "hdpart=0:1\0" \ "hdfile=boot/uImage\0" \ "hdload=echo Loading ${hdpart}:${hdfile};ext2load ide ${hdpart} ${ldaddr} ${hdfile};ext2load ide ${hdpart} 7f0000 boot/kuroboxHG.dtb\0" \ "boothd=setenv bootargs " CONFIG_BOOTARGS ";bootm ${ldaddr} - 7f0000\0" \ "hdboot=run hdload;run boothd\0" \ "flboot=setenv bootargs root=/dev/hda1;bootm ffc00000\0" \ "emboot=setenv bootargs root=/dev/ram0;bootm ffc00000\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0" \ "bootretry=30\0" \ "bootcmd1=run hdboot;run flboot\0" \ "bootcmd2=run flboot\0" \ "bootcmd3=run emboot\0" \ "writeng=protect off fff70000 fff7ffff;era fff70000 fff7ffff;mw.l 800000 4e474e47 1;cp.b 800000 fff70000 4\0" \ "writeok=protect off fff70000 fff7ffff;era fff70000 fff7ffff;mw.l 800000 4f4b4f4b 1;cp.b 800000 fff70000 4\0" \ "ubpart=0:3\0" \ "ubfile="UBFILE"\0" \ "ubload=echo Loading ${ubpart}:${ubfile};ext2load ide ${ubpart} ${ldaddr} ${ubfile}\0" \ "ubsaddr=fff00000\0" \ "ubeaddr=fff2ffff\0" \ "ubflash=protect off ${ubsaddr} ${ubeaddr};era ${ubsaddr} ${ubeaddr};cp.b ${ldaddr} ${ubsaddr} ${filesize};cmp.b ${ldaddr} ${ubsaddr} ${filesize}\0" \ "upgrade=run ubload ubflash\0" /*----------------------------------------------------------------------- * PCI stuff */ #define CONFIG_PCI /* Verified: CONFIG_PCI_PNP doesn't work */ #undef CONFIG_PCI_PNP #define CONFIG_PCI_SCAN_SHOW #ifndef CONFIG_PCI_PNP /* Keep the following defines in sync with the BAT mappings */ #define PCI_ETH_IOADDR 0xbfff00 #define PCI_ETH_MEMADDR 0xbffffc00 #define PCI_IDE_IOADDR 0xbffed0 #define PCI_IDE_MEMADDR 0xbffffb00 #define PCI_USB0_IOADDR 0 #define PCI_USB0_MEMADDR 0xbfffe000 #define PCI_USB1_IOADDR 0 #define PCI_USB1_MEMADDR 0xbfffd000 #define PCI_USB2_IOADDR 0 #define PCI_USB2_MEMADDR 0xbfffcf00 #endif /*----------------------------------------------------------------------- * Ethernet stuff */ #define CONFIG_NET_MULTI #if defined(CONFIG_LAN) || defined(CONFIG_HLAN) #define CONFIG_TULIP #define CONFIG_TULIP_USE_IO #elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL) #define CONFIG_RTL8169 #endif #define CONFIG_NET_RETRY_COUNT 5 #define CONFIG_NETCONSOLE /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFFC00000 #define CFG_FLASH_SIZE 0x00400000 #define CFG_MONITOR_BASE TEXT_BASE #define CFG_RESET_ADDRESS 0xFFF00100 #define CFG_EUMB_ADDR 0x80000000 #define CFG_PCI_MEM_ADDR 0xB0000000 #define CFG_MISC_REGION_ADDR 0xFE000000 #define CFG_MONITOR_LEN 0x00040000 /* 256 kB */ #define CFG_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */ #define CFG_MEMTEST_START 0x00100000 /* memtest works on */ #define CFG_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */ /* Maximum amount of RAM */ #if defined(CONFIG_HLAN) || defined(CONFIG_LAN) #define CFG_MAX_RAM_SIZE 0x04000000 /* 64MB of SDRAM */ #elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL) #define CFG_MAX_RAM_SIZE 0x08000000 /* 128MB of SDRAM */ #else #error Unknown LinkStation type #endif /*----------------------------------------------------------------------- * Change TEXT_BASE in bord/linkstation/config.mk to get a RAM build * * RAM based builds are for testing purposes. A Linux module, uloader.o, * exists to load U-Boot and pass control to it * * Always do "make clean" after changing the build type */ #if CFG_MONITOR_BASE < CFG_FLASH_BASE #define CFG_RAMBOOT #endif /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area */ #if 1 /* RAM is available when the first C function is called */ #define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + CFG_MAX_RAM_SIZE - 0x1000) #else #define CFG_INIT_RAM_ADDR 0x40000000 #endif #define CFG_INIT_RAM_END 0x1000 #define CFG_GBL_DATA_SIZE 128 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) /*---------------------------------------------------------------------- * Serial configuration */ #define CONFIG_CONS_INDEX 1 #define CONFIG_BAUDRATE 57600 #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } #define CFG_NS16550 #define CFG_NS16550_SERIAL #define CFG_NS16550_REG_SIZE 1 #define CFG_NS16550_CLK get_bus_freq(0) #define CFG_NS16550_COM1 (CFG_EUMB_ADDR + 0x4600) /* Console port */ #define CFG_NS16550_COM2 (CFG_EUMB_ADDR + 0x4500) /* AVR port */ /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. * For the detail description refer to the MPC8245 user's manual. * * Unless indicated otherwise, the values are * taken from the orignal Linkstation boot code * * Most of the low level configuration setttings are normally used * in cpu/mpc824x/cpu_init.c which is NOT used by this implementation. * Low level initialisation is done in board/linkstation/early_init.S * The values below are included for reference purpose only */ /* FIXME: 32.768 MHz is the crystal frequency but */ /* the real frequency is lower by about 0.75% */ #define CONFIG_SYS_CLK_FREQ 32768000 #define CFG_HZ 1000 /* Bit-field values for MCCR1. */ #define CFG_ROMNAL 0 #define CFG_ROMFAL 11 #define CFG_BANK0_ROW 2 /* Only bank 0 used: 13 x n x 4 */ #define CFG_BANK1_ROW 0 #define CFG_BANK2_ROW 0 #define CFG_BANK3_ROW 0 #define CFG_BANK4_ROW 0 #define CFG_BANK5_ROW 0 #define CFG_BANK6_ROW 0 #define CFG_BANK7_ROW 0 /* Bit-field values for MCCR2. */ #define CFG_TSWAIT 0 #if defined(CONFIG_LAN) || defined(CONFIG_HLAN) #define CFG_REFINT 0x15e0 #elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL) #define CFG_REFINT 0x1580 #endif /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */ #define CFG_BSTOPRE 0x91c /* Bit-field values for MCCR3. */ #define CFG_REFREC 7 /* Bit-field values for MCCR4. */ #define CFG_PRETOACT 2 #define CFG_ACTTOPRE 2 /* Original value was 2 */ #define CFG_ACTORW 2 #if defined(CONFIG_LAN) || defined(CONFIG_HLAN) #define CFG_SDMODE_CAS_LAT 2 /* For 100MHz bus */ /*#define CFG_SDMODE_BURSTLEN 3*/ #elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL) #define CFG_SDMODE_CAS_LAT 3 /* For 133MHz bus */ /*#define CFG_SDMODE_BURSTLEN 2*/ #endif #define CFG_REGISTERD_TYPE_BUFFER 1 #define CFG_EXTROM 1 /* Original setting but there is no EXTROM */ #define CFG_REGDIMM 0 #define CFG_DBUS_SIZE2 1 #define CFG_SDMODE_WRAP 0 #define CFG_PGMAX 0x32 /* All boards use this setting. Original 0x92 */ #define CFG_SDRAM_DSCD 0x30 /* Memory bank settings. * Only bits 20-29 are actually used from these vales to set the * start/end addresses. The upper two bits will always be 0, and the lower * 20 bits will be 0x00000 for a start address, or 0xfffff for an end * address. Refer to the MPC8240 book. */ #define CFG_BANK0_START 0x00000000 #define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1) #define CFG_BANK0_ENABLE 1 #define CFG_BANK1_START 0x3ff00000 #define CFG_BANK1_END 0x3fffffff #define CFG_BANK1_ENABLE 0 #define CFG_BANK2_START 0x3ff00000 #define CFG_BANK2_END 0x3fffffff #define CFG_BANK2_ENABLE 0 #define CFG_BANK3_START 0x3ff00000 #define CFG_BANK3_END 0x3fffffff #define CFG_BANK3_ENABLE 0 #define CFG_BANK4_START 0x3ff00000 #define CFG_BANK4_END 0x3fffffff #define CFG_BANK4_ENABLE 0 #define CFG_BANK5_START 0x3ff00000 #define CFG_BANK5_END 0x3fffffff #define CFG_BANK5_ENABLE 0 #define CFG_BANK6_START 0x3ff00000 #define CFG_BANK6_END 0x3fffffff #define CFG_BANK6_ENABLE 0 #define CFG_BANK7_START 0x3ff00000 #define CFG_BANK7_END 0x3fffffff #define CFG_BANK7_ENABLE 0 #define CFG_ODCR 0x15 /*---------------------------------------------------------------------- * Initial BAT mappings */ /* NOTES: * 1) GUARDED and WRITETHROUGH not allowed in IBATS * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT */ /* SDRAM */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_128M | BATU_VS | BATU_VP) #define CFG_DBAT0L CFG_IBAT0L #define CFG_DBAT0U CFG_IBAT0U /* EUMB: 1MB of address space */ #define CFG_IBAT1L (CFG_EUMB_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT) #define CFG_IBAT1U (CFG_EUMB_ADDR | BATU_BL_1M | BATU_VS | BATU_VP) #define CFG_DBAT1L (CFG_IBAT1L | BATL_GUARDEDSTORAGE) #define CFG_DBAT1U CFG_IBAT1U /* PCI Mem: 256MB of address space */ #define CFG_IBAT2L (CFG_PCI_MEM_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT) #define CFG_IBAT2U (CFG_PCI_MEM_ADDR | BATU_BL_256M | BATU_VS | BATU_VP) #define CFG_DBAT2L (CFG_IBAT2L | BATL_GUARDEDSTORAGE) #define CFG_DBAT2U CFG_IBAT2U /* PCI and local ROM/Flash: last 32MB of address space */ #define CFG_IBAT3L (CFG_MISC_REGION_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT) #define CFG_IBAT3U (CFG_MISC_REGION_ADDR | BATU_BL_32M | BATU_VS | BATU_VP) #define CFG_DBAT3L (CFG_IBAT3L | BATL_GUARDEDSTORAGE) #define CFG_DBAT3U CFG_IBAT3U /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. * * FIXME: This doesn't appear to be true for the newer kernels * which map more that 8 MB */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CFG_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ #undef CFG_FLASH_PROTECTION #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } #define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */ #define CFG_MAX_FLASH_SECT 72 /* Max number of sectors per flash */ #define CFG_FLASH_ERASE_TOUT 12000 #define CFG_FLASH_WRITE_TOUT 1000 #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #define CONFIG_ENV_IS_IN_FLASH /* * The original LinkStation flash organisation uses * 448 kB (0xFFF00000 - 0xFFF6FFFF) for the boot loader * We use the last sector of this area to store the environment * which leaves max. 384 kB for the U-Boot itself */ #define CFG_ENV_ADDR 0xFFF60000 #define CFG_ENV_SIZE 0x00010000 #define CFG_ENV_SECT_SIZE 0x00010000 /*----------------------------------------------------------------------- * Cache Configuration */ #define CFG_CACHELINE_SIZE 32 #ifdef CONFIG_CMD_KGDB #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * IDE/ATA definitions */ #undef CONFIG_IDE_LED /* No IDE LED */ #define CONFIG_IDE_RESET /* no reset for ide supported */ #define CONFIG_IDE_PREINIT /* check for units */ #define CONFIG_LBA48 /* 48 bit LBA supported */ #if defined(CONFIG_LAN) || defined(CONFIG_HLAN) || defined(CONFIG_HGLAN) #define CFG_IDE_MAXBUS 1 /* Scan only 1 IDE bus */ #define CFG_IDE_MAXDEVICE 1 /* Only 1 drive per IDE bus */ #elif defined(CONFIG_HGTL) #define CFG_IDE_MAXBUS 2 /* Max. 2 IDE busses */ #define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ #else #error Config IDE: Unknown LinkStation type #endif #define CFG_ATA_BASE_ADDR 0 #define CFG_ATA_DATA_OFFSET 0 /* Offset for data I/O */ #define CFG_ATA_REG_OFFSET 0 /* Offset for normal registers */ #define CFG_ATA_ALT_OFFSET 0 /* Offset for alternate registers */ /*----------------------------------------------------------------------- * Partitions and file system */ #define CONFIG_DOS_PARTITION /*----------------------------------------------------------------------- * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #endif /* __CONFIG_H */