/* * (C) Copyright 2013 Keymile AG * Valentin Longchamp * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef _CONFIG_KMP204X_H #define _CONFIG_KMP204X_H #define CONFIG_PHYS_64BIT #define CONFIG_PPC_P2041 #define CONFIG_SYS_TEXT_BASE 0xfff80000 #define CONFIG_KM_DEF_NETDEV "netdev=eth0\0" #define CONFIG_NAND_ECC_BCH /* common KM defines */ #include "keymile-common.h" #define CONFIG_SYS_RAMBOOT #define CONFIG_RAMBOOT_PBL #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc #define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/keymile/kmp204x/pbi.cfg #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/keymile/kmp204x/rcw_kmp204x.cfg /* High Level Configuration Options */ #define CONFIG_BOOKE #define CONFIG_E500 /* BOOKE e500 family */ #define CONFIG_E500MC /* BOOKE e500mc family */ #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ #define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ #define CONFIG_MP /* support multiple processors */ #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ #define CONFIG_PCI /* Enable PCI/PCIE */ #define CONFIG_PCIE1 /* PCIE controler 1 */ #define CONFIG_PCIE3 /* PCIE controler 3 */ #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ #define CONFIG_SYS_DPAA_RMAN /* RMan */ #define CONFIG_FSL_LAW /* Use common FSL init code */ /* Environment in SPI Flash */ #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_CS 0 #define CONFIG_ENV_SPI_MAX_HZ 20000000 #define CONFIG_ENV_SPI_MODE 0 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */ #define CONFIG_ENV_SIZE 0x004000 /* 16K env */ #define CONFIG_ENV_SECT_SIZE 0x010000 #define CONFIG_ENV_OFFSET_REDUND 0x110000 #define CONFIG_ENV_TOTAL_SIZE 0x020000 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT #ifndef __ASSEMBLY__ unsigned long get_board_sys_clk(unsigned long dummy); #endif #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* * These can be toggled for performance analysis, otherwise use default. */ #define CONFIG_SYS_CACHE_STASHING #define CONFIG_BACKSIDE_L2_CACHE #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ENABLE_36BIT_PHYS #define CONFIG_ADDR_MAP #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00800000 #define CONFIG_SYS_ALT_MEMTEST #define CONFIG_PANIC_HANG /* do not reset board on panic */ /* * Config the L3 Cache as L3 SRAM */ #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ CONFIG_RAMBOOT_TEXT_BASE) #define CONFIG_SYS_L3_SIZE (1024 << 10) #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) #define CONFIG_SYS_DCSRBAR 0xf0000000 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull /* * DDR Setup */ #define CONFIG_VERY_BIG_RAM #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) #define CONFIG_DDR_SPD #define CONFIG_SYS_FSL_DDR3 #define CONFIG_FSL_DDR_INTERACTIVE #define CONFIG_SYS_SPD_BUS_NUM 0 #define SPD_EEPROM_ADDRESS 0x54 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /****************************************************************************** * (PRAM usage) * ... ------------------------------------------------------- * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM * ... |<------------------- pram -------------------------->| * ... ------------------------------------------------------- * @END_OF_RAM: * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose * @CONFIG_KM_PHRAM: address for /var * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application) * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM */ /* size of rootfs in RAM */ #define CONFIG_KM_ROOTFSSIZE 0x0 /* pseudo-non volatile RAM [hex] */ #define CONFIG_KM_PNVRAM 0x80000 /* physical RAM MTD size [hex] */ #define CONFIG_KM_PHRAM 0x100000 /* resereved pram area at the end of memroy [hex] */ #define CONFIG_KM_RESERVED_PRAM 0x0 /* enable protected RAM */ #define CONFIG_PRAM 0 #define CONFIG_KM_CRAMFS_ADDR 0x2000000 #define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */ #define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */ /* * Local Bus Definitions */ /* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */ #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2) /* Nand Flash */ #define CONFIG_NAND_FSL_ELBC #define CONFIG_SYS_NAND_BASE 0xffa00000 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_CMD_NAND #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) #define CONFIG_BCH /* NAND flash config */ #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V) /* valid */ #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ | OR_FCM_BCTLD /* LBCTL not ass */ \ | OR_FCM_SCY_1 /* 1 clk wait cycle */ \ | OR_FCM_RST /* 1 clk read setup */ \ | OR_FCM_PGS /* Large page size */ \ | OR_FCM_CST) /* 0.25 command setup */ #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ /* QRIO FPGA */ #define CONFIG_SYS_QRIO_BASE 0xfb000000 #define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull #define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \ | BR_PS_8 /* Port Size 8 bits */ \ | BR_DECC_OFF /* no error corr */ \ | BR_MS_GPCM /* MSEL = GPCM */ \ | BR_V) /* valid */ #define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \ | OR_GPCM_BCTLD /* no LCTL assert */ \ | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \ | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ | OR_GPCM_TRLX /* relaxed tmgs */ \ | OR_GPCM_EAD) /* extra bus clk cycles */ #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */ #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */ /* bootcounter in QRIO */ #define CONFIG_BOOTCOUNT_LIMIT #define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_QRIO_BASE + 0x20) #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ #define CONFIG_MISC_INIT_R #define CONFIG_LAST_STAGE_INIT #define CONFIG_HWCONFIG /* define to use L1 as initial stack */ #define CONFIG_L1_INIT_RAM #define CONFIG_SYS_INIT_RAM_LOCK #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR /* The assembler doesn't like typecast */ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_MONITOR_LEN (512 * 1024) #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Serial Port - controlled on board with jumper J8 * open - index 2 * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) #define CONFIG_KM_CONSOLE_TTY "ttyS0" /* Use the HUSH parser */ #define CONFIG_SYS_HUSH_PARSER /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT #define CONFIG_OF_BOARD_SETUP #define CONFIG_OF_STDOUT_VIA_ALIAS /* new uImage format support */ #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ #define CONFIG_SYS_I2C #define CONFIG_SYS_NUM_I2C_BUSES 3 #define CONFIG_SYS_I2C_MAX_HOPS 1 #define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE #define CONFIG_SYS_FSL_I2C_SPEED 400000 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 #define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \ } #define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/ /* * eSPI - Enhanced SPI */ #define CONFIG_FSL_ESPI #define CONFIG_SPI_FLASH #define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */ #define CONFIG_SPI_FLASH_STMICRO #define CONFIG_CMD_SF #define CONFIG_SF_DEFAULT_SPEED 20000000 #define CONFIG_SF_DEFAULT_MODE 0 /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ /* controller 1, direct to uli, tgtid 3, Base address 20000 */ #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ /* controller 3, Slot 1, tgtid 1, Base address 202000 */ #define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ /* Qman/Bman */ #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ #define CONFIG_SYS_BMAN_NUM_PORTALS 10 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 #define CONFIG_SYS_DPAA_FMAN #define CONFIG_SYS_DPAA_PME /* Default address of microcode for the Linux Fman driver * env is stored at 0x100000, sector size is 0x10000, x2 (redundant) * ucode is stored after env, so we got 0x120000. */ #define CONFIG_SYS_QE_FW_IN_SPIFLASH #define CONFIG_SYS_QE_FMAN_FW_ADDR 0x120000 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) #define CONFIG_FMAN_ENET #define CONFIG_PHYLIB_10G #define CONFIG_PHY_MARVELL /* there is a marvell phy */ #define CONFIG_PCI_INDIRECT_BRIDGE #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_E1000 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_DOS_PARTITION /* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */ #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11 #define CONFIG_SYS_TBIPA_VALUE 8 #define CONFIG_PHYLIB /* recommended PHY management */ #define CONFIG_ETHPRIME "FM1@DTSEC5" #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ /* * Environment */ #define CONFIG_LOADS_ECHO /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ /* * additionnal command line configuration. */ #define CONFIG_CMD_PCI #define CONFIG_CMD_NET /* we don't need flash support */ #define CONFIG_SYS_NO_FLASH #undef CONFIG_CMD_IMLS #undef CONFIG_CMD_FLASH #undef CONFIG_FLASH_CFI_MTD #undef CONFIG_JFFS2_CMDLINE /* * For booting Linux, the board info and command line data * have to be in the first 64 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ #ifdef CONFIG_CMD_KGDB #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #endif #define __USB_PHY_TYPE utmi /* * Environment Configuration */ #define CONFIG_ENV_OVERWRITE #ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ #define CONFIG_KM_DEF_ENV "km-common=empty\0" #endif #ifndef MTDIDS_DEFAULT # define MTDIDS_DEFAULT "nand0=fsl_elbc_nand" #endif /* MTDIDS_DEFAULT */ #ifndef MTDPARTS_DEFAULT # define MTDPARTS_DEFAULT "mtdparts=" \ "fsl_elbc_nand:" \ "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" #endif /* MTDPARTS_DEFAULT */ /* architecture specific default bootargs */ #define CONFIG_KM_DEF_BOOT_ARGS_CPU "" /* FIXME: FDT_ADDR is unspecified */ #define CONFIG_KM_DEF_ENV_CPU \ "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ "cramfsloadfdt=" \ "cramfsload ${fdt_addr_r} " \ "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \ "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0" \ "update=" \ "sf probe 0;sf erase 0 +${filesize};" \ "sf write ${load_addr_r} 0 ${filesize};\0" \ "" #define CONFIG_HW_ENV_SETTINGS \ "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \ "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ "usb_dr_mode=host\0" #define CONFIG_KM_NEW_ENV \ "newenv=sf probe 0;" \ "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \ __stringify(CONFIG_ENV_TOTAL_SIZE)"\0" /* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */ #ifndef CONFIG_KM_DEF_ARCH #define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" #endif #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_KM_DEF_ENV \ CONFIG_KM_DEF_ARCH \ CONFIG_KM_NEW_ENV \ CONFIG_HW_ENV_SETTINGS \ "EEprom_ivm=pca9547:70:9\0" \ "" #endif /* _CONFIG_KMP204X_H */