/* * Configuation settings for the Sentec Cobra Board. * * (C) Copyright 2003 Josef Baumgartner * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* --- * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board * Date: 2004-03-29 * Author: Florian Schlote * * For a description of configuration options please refer also to the * general u-boot-1.x.x/README file * --- */ /* --- * board/config.h - configuration options, board specific * --- */ #ifndef _CONFIG_COBRA5272_H #define _CONFIG_COBRA5272_H /* --- * Define processor * possible values for Sentec board: only Coldfire M5272 processor supported * (please do not change) * --- */ #define CONFIG_MCF52x2 /* define processor family */ #define CONFIG_M5272 /* define processor type */ /* --- * Defines processor clock - important for correct timings concerning serial * interface etc. * CFG_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms * --- */ #define CFG_HZ 1000 #define CFG_CLK 66000000 #define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ /* --- * Enable use of Ethernet * --- */ #define FEC_ENET /* --- * Define baudrate for UART1 (console output, tftp, ...) * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud * CFG_BAUDRATE_TABLE defines values that can be selected in u-boot command * interface * --- */ #define CONFIG_BAUDRATE 19200 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } /* --- * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change * timeout acc. to your needs * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000 * for 10 sec * --- */ #if 0 #define CONFIG_WATCHDOG #define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ #endif /* --- * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different * bootloader residing in flash ('chainloading'); if you want to use * chainloading or want to compile a u-boot binary that can be loaded into * RAM via BDM set * "#if 0" to "#if 1" * You will need a first stage bootloader then, e. g. colilo or a working BDM * cable (Background Debug Mode) * * Setting #if 0: u-boot will start from flash and relocate itself to RAM * * Please do not forget to modify the setting of TEXT_BASE * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000) * * --- */ #if 0 #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */ #endif /* --- * Configuration for environment * Environment is embedded in u-boot in the second sector of the flash * --- */ #ifndef CONFIG_MONITOR_IS_IN_RAM #define CFG_ENV_OFFSET 0x4000 #define CFG_ENV_SECT_SIZE 0x2000 #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_IS_EMBEDDED 1 #else #define CFG_ENV_ADDR 0xffe04000 #define CFG_ENV_SECT_SIZE 0x2000 #define CFG_ENV_IS_IN_FLASH 1 #endif /* * Command line configuration. */ #include #define CONFIG_CMD_PING #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_LOADB #undef CONFIG_CMD_MII /* *----------------------------------------------------------------------------- * Define user parameters that have to be customized most likely *----------------------------------------------------------------------------- */ /*AUTOBOOT settings - booting images automatically by u-boot after power on*/ #define CONFIG_BOOTDELAY 5 /* used for autoboot, delay in seconds u-boot will wait before starting defined (auto-)boot command, setting to -1 disables delay, setting to 0 will too prevent access to u-boot command interface: u-boot then has to reflashed */ /* The following settings will be contained in the environment block ; if you want to use a neutral environment all those settings can be manually set in u-boot: 'set' command */ #if 0 #define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please enter a valid image address in flash */ #define CONFIG_BOOTARGS " " /* default bootargs that are considered during boot */ /* User network settings */ #define CONFIG_ETHADDR 00:00:00:00:00:09 /* default ethernet MAC addr. */ #define CONFIG_IPADDR 192.168.100.2 /* default board IP address */ #define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */ #endif #define CFG_PROMPT "COBRA > " /* Layout of u-boot prompt*/ #define CFG_LOAD_ADDR 0x20000 /*Defines default RAM address from which user programs will be started */ /*---*/ #define CFG_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ /* *----------------------------------------------------------------------------- * End of user parameters to be customized *----------------------------------------------------------------------------- */ /* --- * Defines memory range for test * --- */ #define CFG_MEMTEST_START 0x400 #define CFG_MEMTEST_END 0x380000 /* --- * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. * --- */ /* --- * Base register address * --- */ #define CFG_MBAR 0x10000000 /* Register Base Addrs */ /* --- * System Conf. Reg. & System Protection Reg. * --- */ #define CFG_SCR 0x0003; #define CFG_SPR 0xffff; /* --- * Ethernet settings * --- */ #define CFG_DISCOVER_PHY #define CFG_ENET_BD_BASE 0x780000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in internal SRAM) */ #define CFG_INIT_RAM_ADDR 0x20000000 #define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ #define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 /* *------------------------------------------------------------------------- * RAM SIZE (is defined above) *----------------------------------------------------------------------- */ /* #define CFG_SDRAM_SIZE 16 */ /* *----------------------------------------------------------------------- */ #define CFG_FLASH_BASE 0xffe00000 #ifdef CONFIG_MONITOR_IS_IN_RAM #define CFG_MONITOR_BASE 0x20000 #else #define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400) #endif #define CFG_MONITOR_LEN 0x20000 #define CFG_MALLOC_LEN (256 << 10) #define CFG_BOOTPARAMS_LEN 64*1024 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ #define CFG_FLASH_ERASE_TOUT 1000 /* flash timeout */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CFG_CACHELINE_SIZE 16 /*----------------------------------------------------------------------- * Memory bank definitions * * Please refer also to Motorola Coldfire user manual - Chapter XXX * */ #define CFG_BR0_PRELIM 0xFFE00201 #define CFG_OR0_PRELIM 0xFFE00014 #define CFG_BR1_PRELIM 0 #define CFG_OR1_PRELIM 0 #define CFG_BR2_PRELIM 0 #define CFG_OR2_PRELIM 0 #define CFG_BR3_PRELIM 0 #define CFG_OR3_PRELIM 0 #define CFG_BR4_PRELIM 0 #define CFG_OR4_PRELIM 0 #define CFG_BR5_PRELIM 0 #define CFG_OR5_PRELIM 0 #define CFG_BR6_PRELIM 0 #define CFG_OR6_PRELIM 0 #define CFG_BR7_PRELIM 0x00000701 #define CFG_OR7_PRELIM 0xFF00007C /*----------------------------------------------------------------------- * LED config */ #define LED_STAT_0 0xffff /*all LEDs off*/ #define LED_STAT_1 0xfffe #define LED_STAT_2 0xfffd #define LED_STAT_3 0xfffb #define LED_STAT_4 0xfff7 #define LED_STAT_5 0xffef #define LED_STAT_6 0xffdf #define LED_STAT_7 0xff00 /*all LEDs on*/ /*----------------------------------------------------------------------- * Port configuration (GPIO) */ #define CFG_PACNT 0x00000000 /* PortA control reg.: All pins are external GPIO*/ #define CFG_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs (1^=output, 0^=input) */ #define CFG_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ #define CFG_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART configuration */ #define CFG_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ #define CFG_PBDAT 0x0000 /* PortB value reg. */ #define CFG_PDCNT 0x00000000 /* PortD control reg. */ #endif /* _CONFIG_COBRA5272_H */