/* * (C) Copyright 2003 * Martin Winistoerfer, martinwinistoerfer@gmx.ch. * * SPDX-License-Identifier: GPL-2.0+ */ /* * File: cmi_mpc5xx.h * * Discription: Config header file for cmi * board using an MPC5xx CPU * */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options */ #define CONFIG_MPC555 1 /* This is an MPC555 CPU */ #define CONFIG_CMI 1 /* Using the customized cmi board */ #define CONFIG_SYS_TEXT_BASE 0x02000000 /* Boot from flash at location 0x00000000 */ /* Serial Console Configuration */ #define CONFIG_5xx_CONS_SCI1 #undef CONFIG_5xx_CONS_SCI2 #define CONFIG_BAUDRATE 57600 /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include <config_cmd_default.h> #undef CONFIG_CMD_NET /* disabeled - causes compile errors */ #undef CONFIG_CMD_NFS #define CONFIG_CMD_MEMORY #define CONFIG_CMD_LOADB #define CONFIG_CMD_REGINFO #define CONFIG_CMD_FLASH #define CONFIG_CMD_LOADS #define CONFIG_CMD_ASKENV #define CONFIG_CMD_BDI #define CONFIG_CMD_CONSOLE #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_RUN #define CONFIG_CMD_IMI #if 0 #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ #else #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #endif #define CONFIG_BOOTCOMMAND "go 02034004" /* autoboot command */ #define CONFIG_BOOTARGS "" /* Assuming OS Image in 4 flash sector at offset 4004 */ #define CONFIG_WATCHDOG /* turn on platform specific watchdog */ #define CONFIG_STATUS_LED 1 /* Enable status led */ #define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x000fa000 /* 1 MB in SRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 } /* * Low Level Configuration Settings */ /* * Internal Memory Mapped (This is not the IMMR content) */ #define CONFIG_SYS_IMMR 0x01000000 /* Physical start adress of internal memory map */ /* * Definitions for initial stack pointer and data area */ #define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */ #define CONFIG_SYS_INIT_RAM_SIZE (CONFIG_SYS_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */ #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_RAM_ADDR) - GENERATED_GBL_DATA_SIZE) /* Offset from the beginning of ram */ #define CONFIG_SYS_INIT_SP_ADDR 0x013fa000 /* Physical start adress of inital stack */ /* * Start addresses for the final memory configuration * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */ #define CONFIG_SYS_FLASH_BASE 0x02000000 /* External flash */ #define PLD_BASE 0x03000000 /* PLD */ #define ANYBUS_BASE 0x03010000 /* Anybus Module */ #define CONFIG_SYS_RESET_ADRESS 0x01000000 /* Adress which causes reset */ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* CONFIG_SYS_TEXT_BASE is defined in the board config.mk file. */ /* This adress is given to the linker with -Ttext to */ /* locate the text section at this adress. */ #define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ #define CONFIG_SYS_MALLOC_LEN (64 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization *----------------------------------------------------------------------- * */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */ #define CONFIG_SYS_FLASH_PROTECTION 1 /* Physically section protection on */ #define CONFIG_ENV_IS_IN_FLASH 1 #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_OFFSET 0x00020000 /* Environment starts at this adress */ #define CONFIG_ENV_SIZE 0x00010000 /* Set whole sector as env */ #define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ #endif /*----------------------------------------------------------------------- * SYPCR - System Protection Control * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * SW Watchdog freeze */ #if defined(CONFIG_WATCHDOG) #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) #else #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWP) #endif /* CONFIG_WATCHDOG */ /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled */ #define CONFIG_SYS_PISCR (PISCR_PITF) /*----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register *----------------------------------------------------------------------- * Set clock output, timebase and RTC source and divider, * power management and some other internal clocks */ #define SCCR_MASK SCCR_EBDF00 #define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \ SCCR_COM00 | SCCR_DFNL000 | SCCR_DFNH000) /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration *----------------------------------------------------------------------- * Data show cycle */ #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00) /* Disable data show cycle */ /*----------------------------------------------------------------------- * PLPRCR - PLL, Low-Power, and Reset Control Register *----------------------------------------------------------------------- * Set all bits to 40 Mhz * */ #define CONFIG_SYS_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */ #define CONFIG_SYS_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0) /*----------------------------------------------------------------------- * UMCR - UIMB Module Configuration Register *----------------------------------------------------------------------- * */ #define CONFIG_SYS_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */ /*----------------------------------------------------------------------- * ICTRL - I-Bus Support Control Register */ #define CONFIG_SYS_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */ /*----------------------------------------------------------------------- * USIU - Memory Controller Register *----------------------------------------------------------------------- */ #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_V | BR_BI | BR_PS_16) #define CONFIG_SYS_OR0_PRELIM (OR_ADDR_MK_FF | OR_SCY_3) #define CONFIG_SYS_BR1_PRELIM (ANYBUS_BASE) #define CONFIG_SYS_OR1_PRELIM (OR_ADDR_MK_FFFF | OR_SCY_1 | OR_ETHR) #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_SDRAM_BASE | BR_V | BR_PS_32) #define CONFIG_SYS_OR2_PRELIM (OR_ADDR_MK_FF) #define CONFIG_SYS_BR3_PRELIM (PLD_BASE | BR_V | BR_BI | BR_LBDIR | BR_PS_8) #define CONFIG_SYS_OR3_PRELIM (OR_ADDR_MK_FF | OR_TRLX | OR_BSCY | OR_SCY_8 | \ OR_ACS_10 | OR_ETHR | OR_CSNT) #define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* We don't realign the flash */ /*----------------------------------------------------------------------- * DER - Timer Decrementer *----------------------------------------------------------------------- * Initialise to zero */ #define CONFIG_SYS_DER 0x00000000 #endif /* __CONFIG_H */