/* * U-boot - Configuration file for BlackStamp board * Configuration by Ben Matthews for UR LLE using bf533-stamp.h * as a template * See http://blackfin.uclinux.org/gf/project/blackstamp/ */ #ifndef __CONFIG_BLACKSTAMP_H__ #define __CONFIG_BLACKSTAMP_H__ #include /* * Debugging: Set these options if you're having problems */ /* * #define CONFIG_DEBUG_EARLY_SERIAL * #define DEBUG * #define CONFIG_DEBUG_DUMP * #define CONFIG_DEBUG_DUMP_SYMS */ #define CONFIG_PANIC_HANG 0 /* CPU Options * Be sure to set the Silicon Revision Correctly */ #define CONFIG_BFIN_CPU bf532-0.5 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER /* * Board settings */ #define CONFIG_DRIVER_SMC91111 1 #define CONFIG_SMC91111_BASE 0x20300300 /* FLASH/ETHERNET uses the same address range * Depending on what you have the CPLD doing * this probably isn't needed */ #define SHARED_RESOURCES 1 /* Is I2C bit-banged? */ #undef CONFIG_SOFT_I2 /* * Clock Settings * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV */ /* CONFIG_CLKIN_HZ is any value in Hz */ #define CONFIG_CLKIN_HZ 25000000 /* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ /* 1 = CLKIN / 2 */ #define CONFIG_CLKIN_HALF 0 /* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ /* 1 = bypass PLL */ #define CONFIG_PLL_BYPASS 0 /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ /* Values can range from 0-63 (where 0 means 64) */ #define CONFIG_VCO_MULT 16 /* CCLK_DIV controls the core clock divider */ /* Values can be 1, 2, 4, or 8 ONLY */ #define CONFIG_CCLK_DIV 1 /* SCLK_DIV controls the system clock divider */ /* Values can range from 1-15 */ #define CONFIG_SCLK_DIV 3 /* * Network settings */ #ifdef CONFIG_DRIVER_SMC91111 #define CONFIG_IPADDR 192.168.0.15 #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_GATEWAYIP 192.168.0.1 #define CONFIG_SERVERIP 192.168.0.2 #define CONFIG_HOSTNAME blackstamp #define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs #define CONFIG_SYS_AUTOLOAD "no" /* To remove hardcoding and enable MAC storage in EEPROM */ /* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ #endif #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_OFFSET 0x4000 #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x40000 #define ENV_IS_EMBEDDED_CUSTOM /* * SDRAM settings & memory map */ #define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ #define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */ #define CONFIG_SYS_MONITOR_LEN (256 << 10) #define CONFIG_SYS_MALLOC_LEN (384 << 10) /* * Command settings */ #define CONFIG_SYS_LONGHELP 1 #define CONFIG_CMDLINE_EDITING 1 #define CONFIG_AUTO_COMPLETE 1 #define CONFIG_ENV_OVERWRITE 1 #include #ifdef CONFIG_DRIVER_SMC91111 # define CONFIG_CMD_DHCP # define CONFIG_CMD_PING #else # undef CONFIG_CMD_NET #endif #ifdef CONFIG_SOFT_I2C # define CONFIG_CMD_I2C #endif #define CONFIG_CMD_BOOTLDR #define CONFIG_CMD_CACHE #define CONFIG_CMD_CPLBINFO #define CONFIG_CMD_DATE #define CONFIG_CMD_SF #define CONFIG_CMD_ELF #define CONFIG_BOOTDELAY 5 #define CONFIG_BOOTCOMMAND "run ramboot" #define CONFIG_BOOTARGS \ "root=/dev/mtdblock0 rw " \ "clkin_hz=" MK_STR(CONFIG_CLKIN_HZ) " " \ "earlyprintk=" \ "serial," \ "uart" MK_STR(CONFIG_UART_CONSOLE) "," \ MK_STR(CONFIG_BAUDRATE) " " \ "console=ttyBF0," MK_STR(CONFIG_BAUDRATE) #if defined(CONFIG_CMD_NET) # if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) # define UBOOT_ENV_FILE "u-boot.bin" # else # define UBOOT_ENV_FILE "u-boot.ldr" # endif # if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) # ifdef CONFIG_SPI # define UBOOT_ENV_UPDATE \ "eeprom write $(loadaddr) 0x0 $(filesize)" # else # define UBOOT_ENV_UPDATE \ "sf probe " MK_STR(BFIN_BOOT_SPI_SSEL) ";" \ "sf erase 0 0x40000;" \ "sf write $(loadaddr) 0 $(filesize)" # endif # else # define UBOOT_ENV_UPDATE \ "protect off 0x20000000 0x2003FFFF;" \ "erase 0x20000000 0x2003FFFF;" \ "cp.b $(loadaddr) 0x20000000 $(filesize)" # endif # define NETWORK_ENV_SETTINGS \ "ubootfile=" UBOOT_ENV_FILE "\0" \ "update=" \ "tftp $(loadaddr) $(ubootfile);" \ UBOOT_ENV_UPDATE \ "\0" \ "addip=set bootargs $(bootargs) " \ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \ "$(hostname):eth0:off" \ "\0" \ "ramargs=set bootargs " CONFIG_BOOTARGS "\0" \ "ramboot=" \ "tftp $(loadaddr) uImage;" \ "run ramargs;" \ "run addip;" \ "bootm" \ "\0" \ "nfsargs=set bootargs " \ "root=/dev/nfs rw " \ "nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \ "\0" \ "nfsboot=" \ "tftp $(loadaddr) vmImage;" \ "run nfsargs;" \ "run addip;" \ "bootm" \ "\0" #else # define NETWORK_ENV_SETTINGS #endif /* * Console settings */ #define CONFIG_BAUDRATE 57600 #define CONFIG_LOADS_ECHO 1 #define CONFIG_UART_CONSOLE 0 /* * I2C settings * By default PF2 is used as SDA and PF3 as SCL on the Stamp board * Located on the expansion connector on pins 86/85 * Note these pins are arbitrarily chosen because we aren't using * them yet. You can (and probably should) change these values! */ #ifdef CONFIG_SOFT_I2C #define PF_SCL PF9 #define PF_SDA PF8 #define I2C_INIT do { *pFIO_DIR |= PF_SCL; SSYNC(); } while (0) #define I2C_ACTIVE do { *pFIO_DIR |= PF_SDA; *pFIO_INEN &= ~PF_SDA; SSYNC(); } while (0) #define I2C_TRISTATE do { *pFIO_DIR &= ~PF_SDA; *pFIO_INEN |= PF_SDA; SSYNC(); } while (0) #define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0) #define I2C_SDA(bit) \ do { \ if (bit) \ *pFIO_FLAG_S = PF_SDA; \ else \ *pFIO_FLAG_C = PF_SDA; \ SSYNC(); \ } while (0) #define I2C_SCL(bit) \ do { \ if (bit) \ *pFIO_FLAG_S = PF_SCL; \ else \ *pFIO_FLAG_C = PF_SCL; \ SSYNC(); \ } while (0) #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ #define CONFIG_SYS_I2C_SPEED 50000 #define CONFIG_SYS_I2C_SLAVE 0xFE #endif /* * Miscellaneous configurable options */ #define CONFIG_RTC_BFIN 1 /* * Serial Flash Infomation */ #define CONFIG_BFIN_SPI /* For the M25P64 SCK Should be Kept < 20Mhz */ #define CONFIG_ENV_SPI_MAX_HZ 20000000 #define CONFIG_SF_DEFAULT_HZ 20000000 #define CONFIG_SPI_FLASH #define CONFIG_SPI_FLASH_STMICRO /* * FLASH organization and environment definitions */ #define CONFIG_EBIU_AMGCTL_VAL 0xFF #define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 #define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 #define CONFIG_EBIU_SDRRC_VAL 0x268 #define CONFIG_EBIU_SDGCTL_VAL 0x911109 /* Even though Rev C boards have Parallel Flash * We aren't supporting it. Newer versions of the * hardware don't support Parallel Flash at all. */ #define CONFIG_SYS_NO_FLASH #undef CONFIG_CMD_IMLS #undef CONFIG_CMD_JFFS2 #undef CONFIG_CMD_FLASH #include #endif