/* * (C) Copyright 2005 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /************************************************************************ * bamboo.h - configuration for BAMBOO board ***********************************************************************/ #ifndef __CONFIG_H #define __CONFIG_H /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ #define CONFIG_BAMBOO 1 /* Board is BAMBOO */ #define CONFIG_440_EP 1 /* Specific PPC440EP support */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #undef CFG_DRAM_TEST /* disable - takes long time! */ //#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfe000000 /* start of FLASH */ #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory */ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 #define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 #define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 /*Don't change either of these*/ #define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ #define CFG_PCI_BASE 0xe0000000 /* internal PCI regs */ /*Don't change either of these*/ #define CFG_USB_DEVICE 0x50000000 #define CFG_NVRAM_BASE_ADDR 0x80000000 #define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000) /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ #define CFG_INIT_RAM_ADDR 0xf0000000 /* DCache */ #define CFG_INIT_RAM_END 0x2000 #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ #define CFG_KBYTES_SDRAM ( 128 * 1024) /* 128MB */ //#define CFG_SDRAM_BANKS (2) #define CFG_SDRAM_BANKS (1) /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ #define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI 1 /*define this if you want console on UART1*/ #undef CONFIG_UART1_CONSOLE #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * NVRAM/RTC * * NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF * The DS1558 code assumes this condition * *----------------------------------------------------------------------*/ #define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ #define CONFIG_RTC_DS1556 1 /* DS1556 RTC */ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ #if 0 /* test-only */ #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ #define CFG_MAX_FLASH_SECT 256 /* sectors per device */ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 120000 /* Timeout for Flash Write (in ms) */ #else #define CFG_FLASH_CFI /* The flash is CFI compatible */ #define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CFG_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #endif /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ #undef CFG_ENV_IS_IN_NVRAM /*No NVRAM on board*/ #undef CFG_ENV_IS_IN_FLASH /* ... not in flash */ #define CFG_ENV_IS_IN_EEPROM 1 /* Define to allow the user to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CFG_I2C_MULTI_EEPROMS #define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ #define CFG_ENV_OFFSET 0x0 #define CFG_I2C_EEPROM_ADDR (0xa8>>1) #define CFG_I2C_EEPROM_ADDR_LEN 1 #define CFG_EEPROM_PAGE_WRITE_ENABLE #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 #define CONFIG_BOOTCOMMAND "bootm 0xfe000000" /* autoboot command */ #define CONFIG_BOOTDELAY 3 /* disable autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_NET_MULTI 1 /* required for netconsole */ #define CONFIG_PHY1_ADDR 3 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_IPADDR 10.0.4.251 #define CONFIG_ETHADDR 00:10:EC:00:12:34 #define CONFIG_ETH1ADDR 00:10:EC:00:12:35 #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_SERVERIP 10.0.4.115 /* Partitions */ #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION #define CONFIG_ISO_PARTITION #ifdef CONFIG_440_EP /* USB */ #define CONFIG_USB_OHCI #define CONFIG_USB_STORAGE /*Comment this out to enable USB 1.1 device*/ #define USB_2_0_DEVICE #endif /*CONFIG_440_EP*/ #ifdef DEBUG #define CONFIG_PANIC_HANG #else #define CONFIG_HW_WATCHDOG /* watchdog */ #endif #ifdef CONFIG_440_EP /* Need to define POST */ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \ CFG_CMD_DATE | \ CFG_CMD_DHCP | \ CFG_CMD_DIAG | \ CFG_CMD_ECHO | \ CFG_CMD_EEPROM | \ CFG_CMD_ELF | \ /* CFG_CMD_EXT2 |*/ \ /* CFG_CMD_FAT |*/ \ CFG_CMD_I2C | \ /* CFG_CMD_IDE |*/ \ CFG_CMD_IRQ | \ /* CFG_CMD_KGDB |*/ \ CFG_CMD_MII | \ CFG_CMD_PCI | \ CFG_CMD_PING | \ CFG_CMD_REGINFO | \ CFG_CMD_SDRAM | \ CFG_CMD_FLASH | \ /* CFG_CMD_SPI |*/ \ CFG_CMD_USB | \ 0 ) & ~CFG_CMD_IMLS) #else #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \ CFG_CMD_DATE | \ CFG_CMD_DHCP | \ CFG_CMD_DIAG | \ CFG_CMD_ECHO | \ CFG_CMD_EEPROM | \ CFG_CMD_ELF | \ /* CFG_CMD_EXT2 |*/ \ /* CFG_CMD_FAT |*/ \ CFG_CMD_I2C | \ /* CFG_CMD_IDE |*/ \ CFG_CMD_IRQ | \ /* CFG_CMD_KGDB |*/ \ CFG_CMD_MII | \ CFG_CMD_PCI | \ CFG_CMD_PING | \ CFG_CMD_REGINFO | \ CFG_CMD_SDRAM | \ CFG_CMD_FLASH | \ /* CFG_CMD_SPI |*/ \ 0 ) & ~CFG_CMD_IMLS) #endif /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include /* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CFG_LOAD_ADDR 0x100000 /* default load address */ #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ #define CONFIG_LYNXKDI 1 /* support kdi files */ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ /* General PCI */ #define CONFIG_PCI /* include pci support */ #undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ /* Board-specific PCI */ #define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ #define CFG_PCI_TARGET_INIT #define CFG_PCI_MASTER_INIT #define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */ #define CFG_CACHELINE_SIZE 32 /* ... */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif #endif /* __CONFIG_H */