/* * (C) Copyright 2009 Wolfgang Denk <wd@denx.de> * (C) Copyright 2009, DAVE Srl <www.dave.eu> * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * Aria board configuration file */ #ifndef __CONFIG_H #define __CONFIG_H #define CONFIG_ARIA 1 /* * Memory map for the ARIA board: * * 0x0000_0000-0x0FFF_FFFF DDR RAM (256 MB) * 0x3000_0000-0x3001_FFFF On Chip SRAM (128 KB) * 0x3010_0000-0x3011_FFFF On Board SRAM (128 KB) - CS6 * 0x3020_0000-0x3021_FFFF FPGA (128 KB) - CS2 * 0x8000_0000-0x803F_FFFF IMMR (4 MB) * 0x8400_0000-0x82FF_FFFF PCI I/O space (16 MB) * 0xA000_0000-0xAFFF_FFFF PCI memory space (256 MB) * 0xB000_0000-0xBFFF_FFFF PCI memory mapped I/O space (256 MB) * 0xFC00_0000-0xFFFF_FFFF NOR Boot FLASH (64 MB) */ /* * High Level Configuration Options */ #define CONFIG_E300 1 /* E300 Family */ #define CONFIG_MPC512X 1 /* MPC512X family */ #define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ #define CONFIG_FSL_DIU_LOGO_BMP 1 /* Don't include FSL DIU binary bmp */ /* video */ #undef CONFIG_VIDEO #if defined(CONFIG_VIDEO) #define CONFIG_CFB_CONSOLE #define CONFIG_VGA_AS_SINGLE_DEVICE #endif /* CONFIG_PCI is defined at config time */ #define CONFIG_SYS_MPC512X_CLKIN 33000000 /* in Hz */ #define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */ #define CONFIG_MISC_INIT_R #define CONFIG_SYS_IMMR 0x80000000 #define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_IMMR+0x2100) #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ #define CONFIG_SYS_MEMTEST_END 0x00400000 /* * DDR Setup - manually set all parameters as there's no SPD etc. */ #define CONFIG_SYS_DDR_SIZE 256 /* MB */ #define CONFIG_SYS_DDR_BASE 0x00000000 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE /* DDR Controller Configuration * * SYS_CFG: * [31:31] MDDRC Soft Reset: Diabled * [30:30] DRAM CKE pin: Enabled * [29:29] DRAM CLK: Enabled * [28:28] Command Mode: Enabled (For initialization only) * [27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10] * [24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10] * [20:19] Read Test: DON'T USE * [18:18] Self Refresh: Enabled * [17:17] 16bit Mode: Disabled * [16:13] Ready Delay: 2 * [12:12] Half DQS Delay: Disabled * [11:11] Quarter DQS Delay: Disabled * [10:08] Write Delay: 2 * [07:07] Early ODT: Disabled * [06:06] On DIE Termination: Disabled * [05:05] FIFO Overflow Clear: DON'T USE here * [04:04] FIFO Underflow Clear: DON'T USE here * [03:03] FIFO Overflow Pending: DON'T USE here * [02:02] FIFO Underlfow Pending: DON'T USE here * [01:01] FIFO Overlfow Enabled: Enabled * [00:00] FIFO Underflow Enabled: Enabled * TIME_CFG0 * [31:16] DRAM Refresh Time: 0 CSB clocks * [15:8] DRAM Command Time: 0 CSB clocks * [07:00] DRAM Precharge Time: 0 CSB clocks * TIME_CFG1 * [31:26] DRAM tRFC: * [25:21] DRAM tWR1: * [20:17] DRAM tWRT1: * [16:11] DRAM tDRR: * [10:05] DRAM tRC: * [04:00] DRAM tRAS: * TIME_CFG2 * [31:28] DRAM tRCD: * [27:23] DRAM tFAW: * [22:19] DRAM tRTW1: * [18:15] DRAM tCCD: * [14:10] DRAM tRTP: * [09:05] DRAM tRP: * [04:00] DRAM tRPA */ #define CONFIG_SYS_MDDRC_SYS_CFG 0xF8604A00 #define CONFIG_SYS_MDDRC_SYS_CFG_RUN 0xE8604A00 /*#define CONFIG_SYS_MDDRC_TIME_CFG1 0x54EC1168 */ #define CONFIG_SYS_MDDRC_TIME_CFG1 0x55D81189 /*#define CONFIG_SYS_MDDRC_TIME_CFG2 0x35210864 */ #define CONFIG_SYS_MDDRC_TIME_CFG2 0x34790863 #define CONFIG_SYS_MDDRC_SYS_CFG_EN 0xF0000000 #define CONFIG_SYS_MDDRC_TIME_CFG0 0x00003D2E /*#define CONFIG_SYS_MDDRC_TIME_CFG0_RUN 0x06183D2E */ #define CONFIG_SYS_MDDRC_TIME_CFG0_RUN 0x030C3D2E #define CONFIG_SYS_MICRON_NOP 0x01380000 #define CONFIG_SYS_MICRON_PCHG_ALL 0x01100400 #define CONFIG_SYS_MICRON_EM2 0x01020000 #define CONFIG_SYS_MICRON_EM3 0x01030000 #define CONFIG_SYS_MICRON_EN_DLL 0x01010000 #define CONFIG_SYS_MICRON_RFSH 0x01080000 #define CONFIG_SYS_MICRON_INIT_DEV_OP 0x01000432 #define CONFIG_SYS_MICRON_OCD_DEFAULT 0x01010780 /* DDR Priority Manager Configuration */ #define CONFIG_SYS_MDDRCGRP_PM_CFG1 0x00077777 #define CONFIG_SYS_MDDRCGRP_PM_CFG2 0x00000000 #define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG 0x00000001 #define CONFIG_SYS_MDDRCGRP_LUT0_MU 0xFFEEDDCC #define CONFIG_SYS_MDDRCGRP_LUT0_ML 0xBBAAAAAA #define CONFIG_SYS_MDDRCGRP_LUT1_MU 0x66666666 #define CONFIG_SYS_MDDRCGRP_LUT1_ML 0x55555555 #define CONFIG_SYS_MDDRCGRP_LUT2_MU 0x44444444 #define CONFIG_SYS_MDDRCGRP_LUT2_ML 0x44444444 #define CONFIG_SYS_MDDRCGRP_LUT3_MU 0x55555555 #define CONFIG_SYS_MDDRCGRP_LUT3_ML 0x55555558 #define CONFIG_SYS_MDDRCGRP_LUT4_MU 0x11111111 #define CONFIG_SYS_MDDRCGRP_LUT4_ML 0x11111122 #define CONFIG_SYS_MDDRCGRP_LUT0_AU 0xaaaaaaaa #define CONFIG_SYS_MDDRCGRP_LUT0_AL 0xaaaaaaaa #define CONFIG_SYS_MDDRCGRP_LUT1_AU 0x66666666 #define CONFIG_SYS_MDDRCGRP_LUT1_AL 0x66666666 #define CONFIG_SYS_MDDRCGRP_LUT2_AU 0x11111111 #define CONFIG_SYS_MDDRCGRP_LUT2_AL 0x11111111 #define CONFIG_SYS_MDDRCGRP_LUT3_AU 0x11111111 #define CONFIG_SYS_MDDRCGRP_LUT3_AL 0x11111111 #define CONFIG_SYS_MDDRCGRP_LUT4_AU 0x11111111 #define CONFIG_SYS_MDDRCGRP_LUT4_AL 0x11111111 /* * NOR FLASH on the Local Bus */ #define CONFIG_SYS_FLASH_CFI /* use the CFI code */ #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ #define CONFIG_SYS_FLASH_BASE 0xF8000000 /* start of FLASH */ #define CONFIG_SYS_FLASH_SIZE 0x08000000 /* max flash size */ #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* max sectors */ #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_SRAM_BASE 0x30000000 #define CONFIG_SYS_SRAM_SIZE 0x00020000 /* 128 KB */ #define CONFIG_SYS_ARIA_SRAM_BASE 0x30020000 #define CONFIG_SYS_ARIA_SRAM_SIZE 0x20000 /* 128 KB */ #define CONFIG_SYS_ARIA_FPGA_BASE (CONFIG_SYS_ARIA_SRAM_BASE + \ CONFIG_SYS_ARIA_SRAM_SIZE) #define CONFIG_SYS_ARIA_FPGA_SIZE 0x20000 /* 128 KB */ #define CONFIG_SYS_CS0_CFG 0x05059150 #define CONFIG_SYS_CS2_CFG ( (5 << 24) | \ (5 << 16) | \ (1 << 15) | \ (0 << 14) | \ (0 << 13) | \ (1 << 12) | \ (0 << 10) | \ (3 << 8) | /* 32 bit */ \ (0 << 7) | \ (1 << 6) | \ (1 << 4) | \ (0 << 3) | \ (0 << 2) | \ (0 << 1) | \ (0 << 0) \ ) #define CONFIG_SYS_CS6_CFG 0x05059150 /* Use alternative CS timing for CS0 and CS2 */ #define CONFIG_SYS_CS_ALETIMING 0x00000005 /* Use SRAM for initial stack */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SRAM_BASE #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_SRAM_SIZE #define CONFIG_SYS_GBL_DATA_SIZE 0x100 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_BASE TEXT_BASE #define CONFIG_SYS_MONITOR_LEN (256 * 1024) #ifdef CONFIG_FSL_DIU_FB #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) #else #define CONFIG_SYS_MALLOC_LEN (512 * 1024) #endif /* FPGA */ #define CONFIG_ARIA_FPGA 1 /* * Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO /* * Serial console configuration */ #define CONFIG_PSC_CONSOLE 3 /* console on PSC3 */ #if CONFIG_PSC_CONSOLE != 3 #error CONFIG_PSC_CONSOLE must be 3 #endif #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} #define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE #define CONSOLE_FIFO_TX_ADDR FIFOC_PSC3_TX_ADDR #define CONSOLE_FIFO_RX_SIZE FIFOC_PSC3_RX_SIZE #define CONSOLE_FIFO_RX_ADDR FIFOC_PSC3_RX_ADDR #define CONFIG_CMDLINE_EDITING 1 /* command line history */ /* Use the HUSH parser */ #define CONFIG_SYS_HUSH_PARSER #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* * PCI */ #ifdef CONFIG_PCI #define CONFIG_SYS_PCI_MEM_BASE 0xA0000000 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ #define CONFIG_SYS_PCI_MMIO_BASE (CONFIG_SYS_PCI_MEM_BASE + \ CONFIG_SYS_PCI_MEM_SIZE) #define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE #define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ #define CONFIG_SYS_PCI_IO_BASE 0x00000000 #define CONFIG_SYS_PCI_IO_PHYS 0x84000000 #define CONFIG_SYS_PCI_IO_SIZE 0x01000000 /* 16M */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #endif /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* so disable bit-banged I2C */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_SYS_I2C_SLAVE 0x7F #if 0 #define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ #endif /* * IIM - IC Identification Module */ #undef CONFIG_IIM /* * EEPROM configuration for Atmel AT24C32A-10TQ-2.7: * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* * Ethernet configuration */ #define CONFIG_MPC512x_FEC 1 #define CONFIG_NET_MULTI #define CONFIG_PHY_ADDR 0x17 #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_FEC_AN_TIMEOUT 1 #define CONFIG_HAS_ETH0 /* * Environment */ #define CONFIG_ENV_IS_IN_FLASH 1 /* This has to be a multiple of the flash sector size */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ CONFIG_SYS_MONITOR_LEN) #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* one sector (256K) */ /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + \ CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #define CONFIG_LOADS_ECHO 1 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 #include <config_cmd_default.h> #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DHCP #define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #define CONFIG_CMD_I2C #undef CONFIG_CMD_IDE #define CONFIG_CMD_MII #define CONFIG_CMD_NFS #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI #endif #if defined(CONFIG_CMD_IDE) #define CONFIG_DOS_PARTITION #define CONFIG_MAC_PARTITION #define CONFIG_ISO_PARTITION #endif /* defined(CONFIG_CMD_IDE) */ /* * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock. * For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE * is set to 0xFFFF, watchdog timeouts after about 64s. For details * refer to chapter 36 of the MPC5121e Reference Manual. */ /* #define CONFIG_WATCHDOG */ /* enable watchdog */ #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #ifdef CONFIG_CMD_KGDB # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ sizeof(CONFIG_SYS_PROMPT) + 16) /* max number of command args */ #define CONFIG_SYS_MAXARGS 32 /* Boot Argument Buffer Size */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE #define CONFIG_SYS_HZ 1000 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Cache Configuration */ #define CONFIG_SYS_DCACHE_SIZE 32768 #define CONFIG_SYS_CACHELINE_SIZE 32 #ifdef CONFIG_CMD_KGDB #define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of 32 */ #endif #define CONFIG_SYS_HID0_INIT 0x000000000 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ HID0_ICE) #define CONFIG_SYS_HID2 HID2_HBE #define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 #define BOOTFLAG_WARM 0x02 #ifdef CONFIG_CMD_KGDB #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* * Environment Configuration */ #define CONFIG_ENV_OVERWRITE #define CONFIG_TIMESTAMP #define CONFIG_HOSTNAME aria #define CONFIG_BOOTFILE aria/uImage #define CONFIG_ROOTPATH /opt/eldk/ppc_6xx #define CONFIG_LOADADDR 400000 /* default load addr */ #define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_BAUDRATE 115200 #define CONFIG_PREBOOT "echo;" \ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ "echo" #define CONFIG_EXTRA_ENV_SETTINGS \ "u-boot_addr_r=200000\0" \ "kernel_addr_r=600000\0" \ "fdt_addr_r=880000\0" \ "ramdisk_addr_r=900000\0" \ "u-boot_addr=FFF00000\0" \ "kernel_addr=FFC40000\0" \ "fdt_addr=FFEC0000\0" \ "ramdisk_addr=FC040000\0" \ "ramdiskfile=aria/uRamdisk\0" \ "u-boot=aria/u-boot.bin\0" \ "fdtfile=aria/aria.dtb\0" \ "netdev=eth0\0" \ "consdev=ttyPSC0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "addtty=setenv bootargs ${bootargs} " \ "console=${consdev},${baudrate}\0" \ "flash_nfs=run nfsargs addip addtty;" \ "bootm ${kernel_addr} - ${fdt_addr}\0" \ "flash_self=run ramargs addip addtty;" \ "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ "tftp ${fdt_addr_r} ${fdtfile};" \ "run nfsargs addip addtty;" \ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ "net_self=tftp ${kernel_addr_r} ${bootfile};" \ "tftp ${ramdisk_addr_r} ${ramdiskfile};" \ "tftp ${fdt_addr_r} ${fdtfile};" \ "run ramargs addip addtty;" \ "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\ "load=tftp ${u-boot_addr_r} ${u-boot}\0" \ "update=protect off ${u-boot_addr} +${filesize};" \ "era ${u-boot_addr} +${filesize};" \ "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0" \ "upd=run load update\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES 1 #define OF_CPU "PowerPC,5121@0" #define OF_SOC_COMPAT "fsl,mpc5121-immr" #define OF_TBCLK (bd->bi_busfreq / 4) #define OF_STDOUT_PATH "/soc@80000000/serial@11300" /*----------------------------------------------------------------------- * IDE/ATA stuff *----------------------------------------------------------------------- */ #undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ #undef CONFIG_IDE_LED /* LED for IDE not supported */ #define CONFIG_IDE_RESET /* reset for IDE supported */ #define CONFIG_IDE_PREINIT #define CONFIG_SYS_IDE_MAXBUS 1 /* 1 IDE bus */ #define CONFIG_SYS_IDE_MAXDEVICE 2 /* 1 drive per IDE bus */ #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 #define CONFIG_SYS_ATA_BASE_ADDR get_pata_base() /* Offset for data I/O RefMan MPC5121EE Table 28-10 */ #define CONFIG_SYS_ATA_DATA_OFFSET (0x00A0) /* Offset for normal register accesses */ #define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* Offset for alternate registers RefMan MPC5121EE Table 28-23 */ #define CONFIG_SYS_ATA_ALT_OFFSET (0x00D8) /* Interval between registers */ #define CONFIG_SYS_ATA_STRIDE 4 #define ATA_BASE_ADDR get_pata_base() /* * Control register bit definitions */ #define FSL_ATA_CTRL_FIFO_RST_B 0x80000000 #define FSL_ATA_CTRL_ATA_RST_B 0x40000000 #define FSL_ATA_CTRL_FIFO_TX_EN 0x20000000 #define FSL_ATA_CTRL_FIFO_RCV_EN 0x10000000 #define FSL_ATA_CTRL_DMA_PENDING 0x08000000 #define FSL_ATA_CTRL_DMA_ULTRA 0x04000000 #define FSL_ATA_CTRL_DMA_WRITE 0x02000000 #define FSL_ATA_CTRL_IORDY_EN 0x01000000 #endif /* __CONFIG_H */