/* * (C) Copyright 2006-2008 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef __CONFIG_H #define __CONFIG_H /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ #define CONFIG_ALPR 1 /* Board is ebony */ #define CONFIG_440GX 1 /* Specifc GX support */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */ #define CONFIG_SYS_TEXT_BASE 0xFFFC0000 #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ #define CONFIG_4xx_DCACHE /* Enable i- and d-cache */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CONFIG_SYS_FLASH_BASE 0xffe00000 /* start of FLASH */ #define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CONFIG_SYS_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 #define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 #define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 #define CONFIG_SYS_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000) #define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ #define CONFIG_SYS_TEMP_STACK_OCM 1 #define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #define CONFIG_CONS_INDEX 2 /* Use UART1 */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ #define CONFIG_SYS_FLASH_CFI 1 /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ #define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */ #undef CONFIG_SDRAM_ECC /* enable ECC support */ #define CONFIG_SYS_SDRAM_TABLE { \ {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \ {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_PPC4XX #define CONFIG_SYS_I2C_PPC4XX_CH0 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ /*----------------------------------------------------------------------- * I2C EEPROM (PCF8594C) *----------------------------------------------------------------------*/ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */ /* 8 byte page write mode using */ /* last 3 bits of the address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */ #define CONFIG_PREBOOT "echo;" \ "echo Type \"run kernelx\" to boot the system;" \ "echo" #undef CONFIG_BOOTARGS #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth3\0" \ "hostname=alpr\0" \ "fdt_file=alpr/alpr.dtb\0" \ "fdt_addr=400000\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath} ${init}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \ "mem=193M\0" \ "flash_nfs=run nfsargs addip addtty;" \ "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip addtty;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ "bootm\0" \ "net_nfs_fdt=tftp 200000 ${bootfile};" \ "tftp ${fdt_addr} ${fdt_file};" \ "run nfsargs addip addtty;" \ "bootm 200000 - ${fdt_addr}\0" \ "rootpath=/opt/projects/alpr/nfs_root\0" \ "bootfile=/alpr/uImage\0" \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \ "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ "cp.b 100000 fffc0000 40000;" \ "setenv filesize;saveenv\0" \ "upd=run load update\0" \ "ethprime=ppc_4xx_eth3\0" \ "ethact=ppc_4xx_eth3\0" \ "autoload=no\0" \ "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \ "load_fpga=fpga load 0 ffe00000 10dd9a\0" \ "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \ "rootfstype=jffs2 init=/sbin/init\0" \ "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\ ";bootm 200000\0" \ "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \ "addtty;bootm 200000\0" \ "kernel1=setenv actkernel 'kernel1';run load_fpga " \ "kernel1_mtd\0" \ "kernel2=setenv actkernel 'kernel2';run load_fpga " \ "kernel2_mtd\0" \ "" #define CONFIG_BOOTCOMMAND "run kernel2" #define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */ #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */ #define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */ #define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */ #define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 #define CONFIG_HAS_ETH3 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_NETCONSOLE /* include NetConsole support */ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_DHCP #define CONFIG_CMD_EEPROM #define CONFIG_CMD_FPGA #define CONFIG_CMD_I2C #undef CONFIG_CMD_LOADB #undef CONFIG_CMD_LOADS #define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_NET #undef CONFIG_CMD_NFS #define CONFIG_CMD_PCI #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_ALT_MEMTEST 1 /* Enable more extensive memtest*/ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ #define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ /* General PCI */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ #define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/ /* Board-specific PCI */ #define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ #define CONFIG_SYS_PCI_MASTER_INIT #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ /*----------------------------------------------------------------------- * FPGA stuff *-----------------------------------------------------------------------*/ #define CONFIG_FPGA #define CONFIG_FPGA_ALTERA #define CONFIG_FPGA_CYCLON2 #define CONFIG_SYS_FPGA_CHECK_CTRLC #define CONFIG_SYS_FPGA_PROG_FEEDBACK #define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in Reihe geschaltet -> sollte gehen, aufpassen mit Datasize ist jetzt halt doppelt so gross ... Seite 306 ist das mit den multiple Device in PS Mode erklaert ...*/ /* FPGA program pin configuration */ #define CONFIG_SYS_GPIO_CLK 18 /* FPGA clk pin (cpu output) */ #define CONFIG_SYS_GPIO_DATA 19 /* FPGA data pin (cpu output) */ #define CONFIG_SYS_GPIO_STATUS 20 /* FPGA status pin (cpu input) */ #define CONFIG_SYS_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */ #define CONFIG_SYS_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */ #define CONFIG_SYS_GPIO_SEL_DPR 14 /* cpu output */ #define CONFIG_SYS_GPIO_SEL_AVR 15 /* cpu output */ #define CONFIG_SYS_GPIO_PROG_EN 23 /* cpu output */ /*----------------------------------------------------------------------- * Definitions for GPIO setup *-----------------------------------------------------------------------*/ #define CONFIG_SYS_GPIO_SHUTDOWN (0x80000000 >> 6) #define CONFIG_SYS_GPIO_SSD_EMPTY (0x80000000 >> 9) #define CONFIG_SYS_GPIO_EREADY (0x80000000 >> 26) #define CONFIG_SYS_GPIO_REV0 (0x80000000 >> 14) #define CONFIG_SYS_GPIO_REV1 (0x80000000 >> 15) /*----------------------------------------------------------------------- * NAND-FLASH stuff *-----------------------------------------------------------------------*/ #define CONFIG_SYS_MAX_NAND_DEVICE 4 #define CONFIG_SYS_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */ #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2, \ CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 } #define CONFIG_SYS_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ #define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ #define CONFIG_SYS_EBC_PB0AP 0x92015480 #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */ /* Memory Bank 1 (NAND-FLASH) initialization */ #define CONFIG_SYS_EBC_PB1AP 0x01840380 /* TWT=3 */ #define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #endif /* __CONFIG_H */