/* * (C) Copyright 2006-2008 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #ifndef __CONFIG_H #define __CONFIG_H /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ #define CONFIG_ALPR 1 /* Board is ebony */ #define CONFIG_440GX 1 /* Specifc GX support */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */ #undef CFG_DRAM_TEST /* Disable-takes long time! */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ #define CONFIG_4xx_DCACHE /* Enable i- and d-cache */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xffe00000 /* start of FLASH */ #define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 #define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 #define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 #define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000) #define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000) /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ #define CFG_TEMP_STACK_OCM 1 #define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE #define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ #define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #undef CFG_EXT_SERIAL_CLOCK #define CONFIG_BAUDRATE 115200 #define CONFIG_UART1_CONSOLE /* define for uart1 as console */ #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ #define CFG_FLASH_CFI 1 /* The flash is CFI compatible */ #define CFG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */ #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ #define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */ #undef CONFIG_SDRAM_ECC /* enable ECC support */ #define CFG_SDRAM_TABLE { \ {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \ {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ /*----------------------------------------------------------------------- * I2C EEPROM (PCF8594C) *----------------------------------------------------------------------*/ #define CFG_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */ #define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ #define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 #define CFG_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */ /* 8 byte page write mode using */ /* last 3 bits of the address */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE #define CONFIG_PREBOOT "echo;" \ "echo Type \"run kernelx\" to boot the system;" \ "echo" #undef CONFIG_BOOTARGS #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth3\0" \ "hostname=alpr\0" \ "fdt_file=alpr/alpr.dtb\0" \ "fdt_addr=400000\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath} ${init}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate} " \ "mem=193M\0" \ "flash_nfs=run nfsargs addip addtty;" \ "bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip addtty;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ "bootm\0" \ "net_nfs_fdt=tftp 200000 ${bootfile};" \ "tftp ${fdt_addr} ${fdt_file};" \ "run nfsargs addip addtty;" \ "bootm 200000 - ${fdt_addr}\0" \ "rootpath=/opt/projects/alpr/nfs_root\0" \ "bootfile=/alpr/uImage\0" \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ "load=tftp 100000 /alpr/u-boot/u-boot.bin\0" \ "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ "cp.b 100000 fffc0000 40000;" \ "setenv filesize;saveenv\0" \ "upd=run load update\0" \ "ethprime=ppc_4xx_eth3\0" \ "ethact=ppc_4xx_eth3\0" \ "autoload=no\0" \ "ipconfig=dhcp;setenv serverip 11.0.0.152\0" \ "load_fpga=fpga load 0 ffe00000 10dd9a\0" \ "mtdargs=setenv bootargs root=/dev/mtdblock6 rw " \ "rootfstype=jffs2 init=/sbin/init\0" \ "kernel1_mtd=nand read 200000 0 200000;run mtdargs addip addtty"\ ";bootm 200000\0" \ "kernel2_mtd=nand read 200000 200000 200000;run mtdargs addip " \ "addtty;bootm 200000\0" \ "kernel1=setenv actkernel 'kernel1';run load_fpga " \ "kernel1_mtd\0" \ "kernel2=setenv actkernel 'kernel2';run load_fpga " \ "kernel2_mtd\0" \ "" #define CONFIG_BOOTCOMMAND "run kernel2" #define CONFIG_BOOTDELAY 2 /* autoboot after 5 seconds */ #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */ #define CONFIG_PHY1_ADDR 0x03 /* dummy setting, no EMAC1 used */ #define CONFIG_PHY2_ADDR 0x01 /* PHY address for EMAC2 */ #define CONFIG_PHY3_ADDR 0x02 /* PHY address for EMAC3 */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 #define CONFIG_HAS_ETH3 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_NETCONSOLE /* include NetConsole support */ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DHCP #define CONFIG_CMD_DIAG #define CONFIG_CMD_EEPROM #define CONFIG_CMD_ELF #define CONFIG_CMD_FPGA #define CONFIG_CMD_I2C #define CONFIG_CMD_IRQ #define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_NET #define CONFIG_CMD_NFS #define CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_ALT_MEMTEST 1 /* Enable more extensive memtest*/ #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CFG_LOAD_ADDR 0x100000 /* default load address */ #define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ #define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ /* General PCI */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ #define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/ /* Board-specific PCI */ #define CFG_PCI_TARGET_INIT /* let board init pci target */ #define CFG_PCI_MASTER_INIT #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ /*----------------------------------------------------------------------- * FPGA stuff *-----------------------------------------------------------------------*/ #define CONFIG_FPGA #define CONFIG_FPGA_ALTERA #define CONFIG_FPGA_CYCLON2 #define CFG_FPGA_CHECK_CTRLC #define CFG_FPGA_PROG_FEEDBACK #define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in Reihe geschaltet -> sollte gehen, aufpassen mit Datasize ist jetzt halt doppelt so gross ... Seite 306 ist das mit den multiple Device in PS Mode erklaert ...*/ /* FPGA program pin configuration */ #define CFG_GPIO_CLK 18 /* FPGA clk pin (cpu output) */ #define CFG_GPIO_DATA 19 /* FPGA data pin (cpu output) */ #define CFG_GPIO_STATUS 20 /* FPGA status pin (cpu input) */ #define CFG_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */ #define CFG_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */ #define CFG_GPIO_SEL_DPR 14 /* cpu output */ #define CFG_GPIO_SEL_AVR 15 /* cpu output */ #define CFG_GPIO_PROG_EN 23 /* cpu output */ /*----------------------------------------------------------------------- * Definitions for GPIO setup *-----------------------------------------------------------------------*/ #define CFG_GPIO_SHUTDOWN (0x80000000 >> 6) #define CFG_GPIO_SSD_EMPTY (0x80000000 >> 9) #define CFG_GPIO_EREADY (0x80000000 >> 26) #define CFG_GPIO_REV0 (0x80000000 >> 14) #define CFG_GPIO_REV1 (0x80000000 >> 15) /*----------------------------------------------------------------------- * NAND-FLASH stuff *-----------------------------------------------------------------------*/ #define CFG_MAX_NAND_DEVICE 4 #define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE #define CFG_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */ #define CFG_NAND_BASE_LIST { CFG_NAND_BASE + 0, CFG_NAND_BASE + 2, \ CFG_NAND_BASE + 4, CFG_NAND_BASE + 6 } #define CFG_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ #define CFG_FLASH CFG_FLASH_BASE /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ #define CFG_EBC_PB0AP 0x92015480 #define CFG_EBC_PB0CR (CFG_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */ /* Memory Bank 1 (NAND-FLASH) initialization */ #define CFG_EBC_PB1AP 0x01840380 /* TWT=3 */ #define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #endif /* __CONFIG_H */