/* * (C) Copyright 2008 Sergey Lapin <slapin@ossfans.org> * * Configuation settings for the AFEB9260 board. * Based on configuration for AT91SAM9260-EK * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef __CONFIG_H #define __CONFIG_H #define CONFIG_AT91SAM9260 /* Atmel AT91SAM9260 SoC*/ #include <asm/arch/hardware.h> #define CONFIG_SYS_TEXT_BASE 0x21f00000 /* ARM asynchronous clock */ #define CONFIG_SYS_AT91_MAIN_CLOCK 18429952 /* from 18.432 MHz crystal */ #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_DISPLAY_CPUINFO #define CONFIG_AFEB9260 /* AFEB9260 Board */ #define CONFIG_ARCH_CPU_INIT #define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ #define CONFIG_SETUP_MEMORY_TAGS 1 #define CONFIG_INITRD_TAG 1 #define CONFIG_SKIP_LOWLEVEL_INIT /* * Hardware drivers */ #define CONFIG_ATMEL_LEGACY #define CONFIG_AT91_GPIO #define CONFIG_AT91_PULLUP 1 #define CONFIG_ATMEL_USART #define CONFIG_USART_BASE ATMEL_BASE_DBGU #define CONFIG_USART_ID ATMEL_ID_SYS #define CONFIG_USART3 /* USART 3 is DBGU */ #define CONFIG_BOOTDELAY 3 /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE 1 #define CONFIG_BOOTP_BOOTPATH 1 #define CONFIG_BOOTP_GATEWAY 1 #define CONFIG_BOOTP_HOSTNAME 1 /* * Command line configuration. */ #include <config_cmd_default.h> #undef CONFIG_CMD_BDI #undef CONFIG_CMD_FPGA #undef CONFIG_CMD_IMI #undef CONFIG_CMD_IMLS #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_SOURCE #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP #define CONFIG_CMD_NAND #define CONFIG_CMD_USB /* SDRAM */ #define CONFIG_NR_DRAM_BANKS 1 #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 #define CONFIG_SYS_SDRAM_SIZE 0x04000000 /* 64 megs */ /* DataFlash */ #define CONFIG_ATMEL_DATAFLASH_SPI #define CONFIG_HAS_DATAFLASH #define CONFIG_SYS_SPI_WRITE_TOUT (5 * CONFIG_SYS_HZ) #define CONFIG_SYS_MAX_DATAFLASH_BANKS 2 #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 0xD0000000 /* CS1 */ #define AT91_SPI_CLK 15000000 #define DATAFLASH_TCSS (0x1a << 16) #define DATAFLASH_TCHS (0x1 << 24) /* NAND flash */ #ifdef CONFIG_CMD_NAND #define CONFIG_NAND_ATMEL #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 #define CONFIG_SYS_NAND_DBW_8 /* our ALE is AD21 */ #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* our CLE is AD22 */ #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 #endif /* NOR flash - no real flash on this board */ #define CONFIG_SYS_NO_FLASH /* Ethernet */ #define CONFIG_MACB #define CONFIG_RESET_PHY_R #define CONFIG_AT91_WANTS_COMMON_PHY #define CONFIG_NET_RETRY_COUNT 20 /* USB */ #define CONFIG_USB_ATMEL #define CONFIG_USB_ATMEL_CLK_SEL_PLLB #define CONFIG_USB_OHCI_NEW #define CONFIG_DOS_PARTITION #define CONFIG_SYS_USB_OHCI_CPU_INIT #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9260_UHP_BASE */ #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1 #define CONFIG_USB_STORAGE #define CONFIG_SYS_LOAD_ADDR 0x21000000 /* load address */ #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE #define CONFIG_SYS_MEMTEST_END 0x21e00000 #define CONFIG_SYS_USE_DATAFLASH_CS1 #define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM1 + 0x1000 -\ GENERATED_GBL_DATA_SIZE) /* bootstrap + u-boot + env + linux in dataflash on CS1 */ #define CONFIG_ENV_IS_IN_DATAFLASH #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + 0x8400) #define CONFIG_ENV_OFFSET 0x4200 #define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + CONFIG_ENV_OFFSET) #define CONFIG_ENV_SIZE 0x4200 #define CONFIG_BOOTCOMMAND "nand read 0x21000000 0xa0000 0x200000; bootm" #define CONFIG_BOOTARGS "console=ttyS0,115200 " \ "root=/dev/mtdblock2 " \ "rw rootfstype=jffs2 panic=20" #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_PROMPT "U-Boot> " #define CONFIG_SYS_CBSIZE 256 #define CONFIG_SYS_MAXARGS 16 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) #define CONFIG_SYS_LONGHELP #define CONFIG_CMDLINE_EDITING /* * Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) #endif