/* * Copyright 2008 Extreme Engineering Solutions, Inc. * Copyright 2007-2008 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * xpedite5370 board configuration file */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ #define CONFIG_MPC8572 1 #define CONFIG_XPEDITE5370 1 #define CONFIG_SYS_BOARD_NAME "XPedite5370" #define CONFIG_NUM_CPUS 2 /* 2 Cores */ #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ #define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */ #define CONFIG_PCI 1 /* Enable PCI/PCIE */ #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ #define CONFIG_PCIE1 1 /* PCIE controler 1 */ #define CONFIG_PCIE2 1 /* PCIE controler 2 */ #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ /* * DDR config */ #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ #define CONFIG_DDR_SPD #define CONFIG_MEM_INIT_VALUE 0xdeadbeef #define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */ #define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */ #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ #define CONFIG_NUM_DDR_CONTROLLERS 2 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 #define CONFIG_DDR_ECC #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_VERY_BIG_RAM #ifndef __ASSEMBLY__ extern unsigned long get_board_sys_clk(unsigned long dummy); extern unsigned long get_board_ddr_clk(unsigned long dummy); #endif #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ /* * These can be toggled for performance analysis, otherwise use default. */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ENABLE_36BIT_PHYS 1 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) #define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) /* * Diagnostics */ #define CONFIG_SYS_ALT_MEMTEST #define CONFIG_SYS_MEMTEST_START 0x10000000 #define CONFIG_SYS_MEMTEST_END 0x20000000 /* * Memory map * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable */ #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3) /* * NAND flash configuration */ #define CONFIG_SYS_NAND_BASE 0xef800000 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ CONFIG_SYS_NAND_BASE2} #define CONFIG_SYS_MAX_NAND_DEVICE 2 #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */ #define CONFIG_NAND_FSL_ELBC /* * NOR flash configuration */ #define CONFIG_SYS_FLASH_BASE 0xf8000000 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ {0xf7f40000, 0xc0000} } #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ /* * Chip select configuration */ /* NOR Flash 0 on CS0 */ #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ BR_PS_16 | \ BR_V) #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ OR_GPCM_CSNT | \ OR_GPCM_XACS | \ OR_GPCM_ACS_DIV2 | \ OR_GPCM_SCY_8 | \ OR_GPCM_TRLX | \ OR_GPCM_EHTR | \ OR_GPCM_EAD) /* NOR Flash 1 on CS1 */ #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ BR_PS_16 | \ BR_V) #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM /* NAND flash on CS2 */ #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ (2<<BR_DECC_SHIFT) | \ BR_PS_8 | \ BR_MS_FCM | \ BR_V) /* NAND flash on CS2 */ #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ OR_FCM_PGS | \ OR_FCM_CSCT | \ OR_FCM_CST | \ OR_FCM_CHT | \ OR_FCM_SCY_1 | \ OR_FCM_TRLX | \ OR_FCM_EHTR) /* NAND flash on CS3 */ #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ (2<<BR_DECC_SHIFT) | \ BR_PS_8 | \ BR_MS_FCM | \ BR_V) #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM /* * Use L1 as initial stack */ #define CONFIG_SYS_INIT_RAM_LOCK 1 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 #define CONFIG_SYS_INIT_RAM_END 0x00004000 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ /* * Serial Port */ #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * Use the HUSH parser */ #define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* * Pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 #define CONFIG_SYS_64BIT_VSPRINTF 1 #define CONFIG_SYS_64BIT_STRTOUL 1 /* * I2C */ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_OFFSET 0x3000 #define CONFIG_SYS_I2C2_OFFSET 0x3100 #define CONFIG_I2C_MULTI_BUS /* PEX8518 slave I2C interface */ #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 /* I2C DS1631 temperature sensor */ #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 #define CONFIG_DTT_DS1621 #define CONFIG_DTT_SENSORS { 0 } /* I2C EEPROM - AT24C128B */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ /* I2C RTC */ #define CONFIG_RTC_M41T11 1 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 /* GPIO/EEPROM/SRAM */ #define CONFIG_DS4510 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51 /* GPIO */ #define CONFIG_PCA953X #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 /* * PU = pulled high, PD = pulled low * I = input, O = output, IO = input/output */ /* PCA9557 @ 0x18*/ #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */ #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */ #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */ #define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */ #define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */ /* PCA9557 @ 0x1c*/ #define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */ #define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */ #define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */ #define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */ #define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */ #define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */ #define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */ #define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */ /* PCA9557 @ 0x1e*/ #define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */ #define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */ #define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */ #define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */ #define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */ #define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */ #define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */ /* PCA9557 @ 0x1f */ #define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */ #define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */ #define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */ #define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */ #define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */ /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ /* PCIE1 - VPX P1 */ #define CONFIG_SYS_PCIE1_MEM_BASE 0x80000000 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ /* PCIE2 - PEX8518 */ #define CONFIG_SYS_PCIE2_MEM_BASE 0xc0000000 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ #define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */ /* * Networking options */ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_NET_MULTI 1 #define CONFIG_TSEC_TBI #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ #define CONFIG_ETHPRIME "eTSEC2" #define CONFIG_TSEC1 1 #define CONFIG_TSEC1_NAME "eTSEC1" #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC1_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define CONFIG_HAS_ETH0 #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "eTSEC2" #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC2_PHY_ADDR 2 #define TSEC2_PHYIDX 0 #define CONFIG_HAS_ETH1 /* * Command configuration. */ #include <config_cmd_default.h> #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE #define CONFIG_CMD_DHCP #define CONFIG_CMD_DS4510 #define CONFIG_CMD_DS4510_INFO #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_ELF #define CONFIG_CMD_FLASH #define CONFIG_CMD_I2C #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_NET #define CONFIG_CMD_PCA953X #define CONFIG_CMD_PCA953X_INFO #define CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_SNTP /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ #define CONFIG_PANIC_HANG /* do not reset board on panic */ #define CONFIG_PREBOOT /* enable preboot variable */ #define CONFIG_FIT 1 #define CONFIG_FIT_VERBOSE 1 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ /* * For booting Linux, the board info and command line data * have to be in the first 16 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ /* * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ /* * Environment Configuration */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ #define CONFIG_ENV_SIZE 0x8000 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) /* * Flash memory map: * fff80000 - ffffffff Pri U-Boot (512 KB) * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) * fff00000 - fff3ffff Pri FDT (256KB) * fef00000 - ffefffff Pri OS image (16MB) * f8000000 - feefffff Pri OS Use/Filesystem (111MB) * * f7f80000 - f7ffffff Sec U-Boot (512 KB) * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) * f7f00000 - f7f3ffff Sec FDT (256KB) * f6f00000 - f7efffff Sec OS image (16MB) * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) */ #define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000) #define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000) #define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000) #define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7f00000) #define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000) #define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000) #define CONFIG_PROG_UBOOT1 \ "$download_cmd $loadaddr $ubootfile; " \ "if test $? -eq 0; then " \ "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ "if test $? -ne 0; then " \ "echo PROGRAM FAILED; " \ "else; " \ "echo PROGRAM SUCCEEDED; " \ "fi; " \ "else; " \ "echo DOWNLOAD FAILED; " \ "fi;" #define CONFIG_PROG_UBOOT2 \ "$download_cmd $loadaddr $ubootfile; " \ "if test $? -eq 0; then " \ "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ "if test $? -ne 0; then " \ "echo PROGRAM FAILED; " \ "else; " \ "echo PROGRAM SUCCEEDED; " \ "fi; " \ "else; " \ "echo DOWNLOAD FAILED; " \ "fi;" #define CONFIG_BOOT_OS_NET \ "$download_cmd $osaddr $osfile; " \ "if test $? -eq 0; then " \ "if test -n $fdtaddr; then " \ "$download_cmd $fdtaddr $fdtfile; " \ "if test $? -eq 0; then " \ "bootm $osaddr - $fdtaddr; " \ "else; " \ "echo FDT DOWNLOAD FAILED; " \ "fi; " \ "else; " \ "bootm $osaddr; " \ "fi; " \ "else; " \ "echo OS DOWNLOAD FAILED; " \ "fi;" #define CONFIG_PROG_OS1 \ "$download_cmd $osaddr $osfile; " \ "if test $? -eq 0; then " \ "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ "if test $? -ne 0; then " \ "echo OS PROGRAM FAILED; " \ "else; " \ "echo OS PROGRAM SUCCEEDED; " \ "fi; " \ "else; " \ "echo OS DOWNLOAD FAILED; " \ "fi;" #define CONFIG_PROG_OS2 \ "$download_cmd $osaddr $osfile; " \ "if test $? -eq 0; then " \ "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ "if test $? -ne 0; then " \ "echo OS PROGRAM FAILED; " \ "else; " \ "echo OS PROGRAM SUCCEEDED; " \ "fi; " \ "else; " \ "echo OS DOWNLOAD FAILED; " \ "fi;" #define CONFIG_PROG_FDT1 \ "$download_cmd $fdtaddr $fdtfile; " \ "if test $? -eq 0; then " \ "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ "if test $? -ne 0; then " \ "echo FDT PROGRAM FAILED; " \ "else; " \ "echo FDT PROGRAM SUCCEEDED; " \ "fi; " \ "else; " \ "echo FDT DOWNLOAD FAILED; " \ "fi;" #define CONFIG_PROG_FDT2 \ "$download_cmd $fdtaddr $fdtfile; " \ "if test $? -eq 0; then " \ "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ "if test $? -ne 0; then " \ "echo FDT PROGRAM FAILED; " \ "else; " \ "echo FDT PROGRAM SUCCEEDED; " \ "fi; " \ "else; " \ "echo FDT DOWNLOAD FAILED; " \ "fi;" #define CONFIG_EXTRA_ENV_SETTINGS \ "autoload=yes\0" \ "download_cmd=tftp\0" \ "console_args=console=ttyS0,115200\0" \ "root_args=root=/dev/nfs rw\0" \ "misc_args=ip=on\0" \ "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ "bootfile=/home/user/file\0" \ "osfile=/home/user/uImage-XPedite5370\0" \ "fdtfile=/home/user/xpedite5370.dtb\0" \ "ubootfile=/home/user/u-boot.bin\0" \ "fdtaddr=c00000\0" \ "osaddr=0x1000000\0" \ "loadaddr=0x1000000\0" \ "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ "prog_os1="CONFIG_PROG_OS1"\0" \ "prog_os2="CONFIG_PROG_OS2"\0" \ "prog_fdt1="CONFIG_PROG_FDT1"\0" \ "prog_fdt2="CONFIG_PROG_FDT2"\0" \ "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ "bootcmd_flash1=run set_bootargs; " \ "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ "bootcmd_flash2=run set_bootargs; " \ "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ "bootcmd=run bootcmd_flash1\0" #endif /* __CONFIG_H */