/* * (C) Copyright 2002 Scott McNutt * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /************************************************************************ * config for XPedite1000 from XES Inc. * Ported from EBONY config by Travis B. Sawyer * (C) Copyright 2003 Sandburst Corporation * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony) ***********************************************************************/ #ifndef __CONFIG_H #define __CONFIG_H /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ #define CONFIG_XPEDITE1K 1 /* Board is XPedite 1000 */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_440 1 #define CONFIG_440GX 1 /* 440 GX */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_R #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ /* POST support */ #define CONFIG_POST (CONFIG_SYS_POST_RTC | \ CONFIG_SYS_POST_I2C) /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) #define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700) #define USR_LED0 0x00000080 #define USR_LED1 0x00000100 #define USR_LED2 0x00000200 #define USR_LED3 0x00000400 #ifndef __ASSEMBLY__ extern unsigned long in32(unsigned int); extern void out32(unsigned int, unsigned long); #define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0)) #define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1)) #define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2)) #define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3)) #define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0)) #define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1)) #define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2)) #define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3)) #endif /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ #define CONFIG_SYS_TEMP_STACK_OCM 1 #define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_BAUDRATE 9600 #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} /*----------------------------------------------------------------------- * NVRAM/RTC * * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located. * The DS1743 code assumes this condition (i.e. -- it assumes the base * address for the RTC registers is: * * CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE * *----------------------------------------------------------------------*/ /* TBS: Xpedite 1000 has STMicro M41T00 via IIC */ #define CONFIG_RTC_M41T11 1 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ #define SPD_EEPROM_ADDRESS {0x54} /* SPD i2c spd addresses */ #define CONFIG_VERY_BIG_RAM 1 /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7f #define CONFIG_SYS_I2C_NOPROBES {0x55,0x56,0x57,0x58,0x59,0x5a,0x5b,0x5c,0x69} /* Don't probe these addrs */ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ #define CONFIG_ENV_IS_IN_EEPROM 1 #define CONFIG_ENV_SIZE 0x100 /* Size of Environment vars */ #define CONFIG_ENV_OFFSET 0x100 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* this is actually the second page of the eeprom */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 #define CONFIG_BOOTARGS "root=/dev/hda1 " #define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */ #define CONFIG_BOOTDELAY 5 /* disable autoboot */ #define CONFIG_BAUDRATE 9600 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address phy0 not populated */ #define CONFIG_PHY1_ADDR 1 /* PHY address phy1 not populated */ #define CONFIG_PHY2_ADDR 4 /* PHY address phy2 */ #define CONFIG_PHY3_ADDR 8 /* PHY address phy3 */ #define CONFIG_NET_MULTI 1 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_HAS_ETH2 1 /* add support for "eth2addr" */ #define CONFIG_HAS_ETH3 1 /* add support for "eth3addr" */ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_PCI #define CONFIG_CMD_IRQ #define CONFIG_CMD_I2C #define CONFIG_CMD_DATE #define CONFIG_CMD_BEDBUG #define CONFIG_CMD_EEPROM #define CONFIG_CMD_PING #define CONFIG_CMD_ELF #define CONFIG_CMD_MII #define CONFIG_CMD_DIAG #define CONFIG_CMD_FAT #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ /* General PCI */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ /* Board-specific PCI */ #define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ #define CONFIG_SYS_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif #endif /* __CONFIG_H */