/* * (C) Copyright 2001 * Erik Theisen, Wave 7 Optics, etheisen@mindspring.com * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_405GP 1 /* This is a PPC405GP CPU */ #define CONFIG_4xx 1 /* ...member of PPC405 family */ #define CONFIG_W7O 1 /* ...on a Wave 7 Optics board */ #define CONFIG_W7OLMG 1 /* ...specifically an LMG */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_F 1 /* and misc_init_f() */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ #define CONFIG_BAUDRATE 9600 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ #if 1 #define CONFIG_BOOTCOMMAND "bootvx" /* VxWorks boot command */ #else #define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ #endif #undef CONFIG_BOOTARGS #define CONFIG_LOADADDR F0080000 #define CONFIG_ETHADDR 00:06:0D:00:00:00 /* Default, overridden at boot */ #define CONFIG_OVERWRITE_ETHADDR_ONCE #define CONFIG_IPADDR 192.168.1.1 #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_SERVERIP 192.168.1.2 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* disallow baudrate change */ #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_SENSORS {2, 4} /* Sensor addresses */ #define CONFIG_SYS_DTT_MAX_TEMP 70 #define CONFIG_SYS_DTT_LOW_TEMP -30 #define CONFIG_SYS_DTT_HYSTERESIS 3 /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_PCI #define CONFIG_CMD_IRQ #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DHCP #define CONFIG_CMD_BEDBUG #define CONFIG_CMD_DATE #define CONFIG_CMD_I2C #define CONFIG_CMD_EEPROM #define CONFIG_CMD_ELF #define CONFIG_CMD_BSP #define CONFIG_CMD_REGINFO #define CONFIG_CMD_DTT #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_HW_WATCHDOG /* HW Watchdog, board specific */ #define CONFIG_SPD_EEPROM /* SPD EEPROM for SDRAM param. */ #define CONFIG_SPDDRAM_SILENT /* No output if spd fails */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "Wave7Optics> " /* Monitor Command Prompt */ #undef CONFIG_SYS_HUSH_PARSER /* No hush parse for U-Boot */ #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ #define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CONFIG_SYS_BASE_BAUD 384000 /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE {9600} #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ #define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ #define PCI_HOST_FORCE 1 /* configure as pci host */ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ #define CONFIG_PCI_PNP /* pci plug-and-play */ /* resource configuration */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */ #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ #define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ #define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ #define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ #define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * Set up values for external bus controller * used by cpu_init.c *----------------------------------------------------------------------- */ /* use PerWE instead of PCI_INT ( these functions share a pin ) */ #define CONFIG_USE_PERWE 1 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ #define CONFIG_SYS_TEMP_STACK_OCM 1 /* bank 0 is boot flash */ /* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ #define CONFIG_SYS_W7O_EBC_PB0AP 0x03050440 /* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */ #define CONFIG_SYS_W7O_EBC_PB0CR 0xFFE38000 /* bank 1 is main flash */ /* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */ #define CONFIG_SYS_EBC_PB1AP 0x04850240 /* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */ #define CONFIG_SYS_EBC_PB1CR 0xF00FC000 /* bank 2 is RTC/NVRAM */ /* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ #define CONFIG_SYS_EBC_PB2AP 0x03000440 /* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */ #define CONFIG_SYS_EBC_PB2CR 0xFC018000 /* bank 3 is FPGA 0 */ /* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */ #define CONFIG_SYS_EBC_PB3AP 0x02000400 /* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */ #define CONFIG_SYS_EBC_PB3CR 0xFD01A000 /* bank 4 is SAM 8 bit range */ /* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ #define CONFIG_SYS_EBC_PB4AP 0x02840380 /* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */ #define CONFIG_SYS_EBC_PB4CR 0xFE878000 /* bank 5 is SAM 16 bit range */ /* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */ #define CONFIG_SYS_EBC_PB5AP 0x05040d80 /* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */ #define CONFIG_SYS_EBC_PB5CR 0xFD87A000 /* bank 6 is unused */ /* pb6ap = 0 */ #define CONFIG_SYS_EBC_PB6AP 0x00000000 /* pb6cr = 0 */ #define CONFIG_SYS_EBC_PB6CR 0x00000000 /* bank 7 is LED register */ /* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ #define CONFIG_SYS_W7O_EBC_PB7AP 0x03050440 /* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */ #define CONFIG_SYS_W7O_EBC_PB7CR 0xFE01C000 /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFFFC0000 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */ #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use real Flash protection */ #if 1 /* Use NVRAM for environment variables */ /*----------------------------------------------------------------------- * NVRAM organization */ #define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */ #define CONFIG_SYS_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */ #define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ #define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ /*define CONFIG_ENV_ADDR \ (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) Env */ #define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR #else /* Use Boot Flash for environment variables */ /*----------------------------------------------------------------------- * Flash EEPROM for environment */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ #define CONFIG_ENV_SIZE 0x10000 /* Total Size of env. sector */ #define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sec tot sze */ #endif /*----------------------------------------------------------------------- * I2C EEPROM (ATMEL 24C04N) */ #define CONFIG_HARD_I2C 1 /* Hardware assisted I2C */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 #define CONFIG_SYS_I2C_MULTI_EEPROMS /*----------------------------------------------------------------------- * Definitions for Serial Presence Detect EEPROM address * (to get SDRAM settings) */ #define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */ /* * Init Memory Controller: */ #define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */ #define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */ /* On Chip Memory location */ #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in RAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* * FPGA(s) configuration */ #define CONFIG_SYS_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */ #define CONFIG_NUM_FPGAS 1 /* Number of FPGAs on board */ #define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */ #define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */ #define CONFIG_FPGAS_BANK_SIZE 0x00100000L /* FPGAs' mmap bank size */ #endif /* __CONFIG_H */