/* * (C) Copyright 2007 * Thomas Waehner, TQ-System GmbH, thomas.waehner@tqs.de. * * (C) Copyright 2005 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * Wolfgang Denk <wd@denx.de> * Copyright 2004 Freescale Semiconductor. * (C) Copyright 2002,2003 Motorola,Inc. * Xianghua Xiao <X.Xiao@motorola.com> * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * TQM85xx (8560/40/55/41/48) board configuration file */ #ifndef __CONFIG_H #define __CONFIG_H /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ #define CONFIG_PCI #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ #define CONFIG_PCIX_CHECK /* PCIX olny works at 66 MHz */ #ifdef CONFIG_TQM8548 #define CONFIG_PCI1 #define CONFIG_PCIE1 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ #endif #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ /* * Configuration for big NOR Flashes * * Define CONFIG_TQM_BIGFLASH for boards with more than 128 MiB NOR Flash. * Please be aware, that this changes the whole memory map (new CCSRBAR * address, etc). You have to use an adapted Linux kernel or FDT blob * if this option is set. */ #undef CONFIG_TQM_BIGFLASH /* * NAND flash support (disabled by default) * * Warning: NAND support will likely increase the U-Boot image size * to more than 256 KB. Please adjust TEXT_BASE if necessary. */ #undef CONFIG_NAND /* * MPC8540 and MPC8548 don't have CPM module */ #if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8548) #define CONFIG_CPM2 1 /* has CPM2 */ #endif #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ #undef CONFIG_CAN_DRIVER /* CAN Driver support */ /* * sysclk for MPC85xx * * Two valid values are: * 33333333 * 66666666 * * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz * is likely the desired value here, so that is now the default. * The board, however, can run at 66MHz. In any event, this value * must match the settings of some switches. Details can be found * in the README.mpc85xxads. */ #ifndef CONFIG_SYS_CLK_FREQ #define CONFIG_SYS_CLK_FREQ 33333333 #endif /* * These can be toggled for performance analysis, otherwise use default. */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ #define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ #define CONFIG_SYS_MEMTEST_START 0x00000000 #define CONFIG_SYS_MEMTEST_END 0x10000000 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ #define CONFIG_SYS_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ #ifdef CONFIG_TQM_BIGFLASH #define CONFIG_SYS_CCSRBAR 0xA0000000 /* relocated CCSRBAR */ #else /* !CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ #endif /* CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ #define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR + 0x8000) #define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000) #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0xa000) /* * DDR Setup */ #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 #if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) /* TQM8540 & 8560 need DLL-override */ #define CONFIG_DDR_DLL /* DLL fix needed */ #define CONFIG_DDR_DEFAULT_CL 25 /* CAS latency 2,5 */ #endif /* CONFIG_TQM8540 || CONFIG_TQM8560 */ #if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) || \ defined(CONFIG_TQM8548) #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ #endif /* CONFIG_TQM8541 || CONFIG_TQM8555 || CONFIG_TQM8548 */ /* * Old TQM85xx boards have 'M' type Spansion Flashes from the S29GLxxxM * series while new boards have 'N' type Flashes from the S29GLxxxN * series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB. */ #ifdef CONFIG_TQM8548 #define CONFIG_TQM_FLASH_N_TYPE #endif /* CONFIG_TQM8548 */ /* * Flash on the Local Bus */ #ifdef CONFIG_TQM_BIGFLASH #define CONFIG_SYS_FLASH0 0xE0000000 #define CONFIG_SYS_FLASH1 0xC0000000 #else /* !CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_FLASH0 0xFC000000 #define CONFIG_SYS_FLASH1 0xF8000000 #endif /* CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } #define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */ #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */ /* Default ORx timings are for <= 41.7 MHz Local Bus Clock. * * Note: According to timing specifications external addr latch delay * (EAD, bit #0) must be set if Local Bus Clock is > 83 MHz. * * For other Local Bus Clocks see following table: * * Clock/MHz CONFIG_SYS_ORx_PRELIM * 166 0x.....CA5 * 133 0x.....C85 * 100 0x.....C65 * 83 0x.....FA2 * 66 0x.....C82 * 50 0x.....C60 * 42 0x.....040 * 33 0x.....030 * 25 0x.....020 * */ #ifdef CONFIG_TQM_BIGFLASH #define CONFIG_SYS_BR0_PRELIM 0xE0001801 /* port size 32bit */ #define CONFIG_SYS_OR0_PRELIM 0xE0000040 /* 512MB Flash */ #define CONFIG_SYS_BR1_PRELIM 0xC0001801 /* port size 32bit */ #define CONFIG_SYS_OR1_PRELIM 0xE0000040 /* 512MB Flash */ #else /* !CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_BR0_PRELIM 0xfc001801 /* port size 32bit */ #define CONFIG_SYS_OR0_PRELIM 0xfc000040 /* 64MB Flash */ #define CONFIG_SYS_BR1_PRELIM 0xf8001801 /* port size 32bit */ #define CONFIG_SYS_OR1_PRELIM 0xfc000040 /* 64MB Flash */ #endif /* CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_FLASH_CFI /* flash is CFI compat. */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */ #define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* speed up output to Flash */ #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ /* * Note: when changing the Local Bus clock divider you have to * change the timing values in CONFIG_SYS_ORx_PRELIM. * * LCRR[00:03] CLKDIV: System (CCB) clock divider. Valid values are 2, 4, 8. * LCRR[16:17] EADC : External address delay cycles. It should be set to 2 * for Local Bus Clock > 83.3 MHz. */ #define CONFIG_SYS_LBC_LCRR 0x00030008 /* LB clock ratio reg */ #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ #define CONFIG_L1_INIT_RAM #define CONFIG_SYS_INIT_RAM_LOCK 1 #define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_CCSRBAR \ + 0x04010000) /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End used area in RAM */ #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (~TEXT_BASE + 1)/* Reserved for Monitor */ #define CONFIG_SYS_MALLOC_LEN (384 * 1024) /* Reserved for malloc */ /* Serial Port */ #if defined(CONFIG_TQM8560) #define CONFIG_CONS_ON_SCC /* define if console on SCC */ #undef CONFIG_CONS_NONE /* define if console on something else */ #define CONFIG_CONS_INDEX 1 /* which serial channel for console */ #else /* !CONFIG_TQM8560 */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) /* PS/2 Keyboard */ #define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ #define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ #define CONFIG_PS2SERIAL 2 /* .. on DUART2 */ #define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ #define CONFIG_BOARD_EARLY_INIT_R 1 #endif /* CONFIG_TQM8560 */ #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ #ifdef CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* CAN */ #define CONFIG_SYS_CAN_BASE (CONFIG_SYS_CCSRBAR \ + 0x03000000) /* CAN base address */ #ifdef CONFIG_CAN_DRIVER #define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 KiB address mask */ #define CONFIG_SYS_OR2_CAN (CONFIG_SYS_CAN_OR_AM | OR_UPM_BI) #define CONFIG_SYS_BR2_CAN ((CONFIG_SYS_CAN_BASE & BR_BA) | \ BR_PS_8 | BR_MS_UPMC | BR_V) #endif /* CONFIG_CAN_DRIVER */ /* * I2C */ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_NOPROBES {0x48} /* Don't probe these addrs */ #define CONFIG_SYS_I2C_OFFSET 0x3000 /* I2C RTC */ #define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ /* I2C EEPROM */ /* * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work also). */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 #define CONFIG_SYS_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ /* I2C SYSMON (LM75) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ #define CONFIG_SYS_DTT_MAX_TEMP 70 #define CONFIG_SYS_DTT_LOW_TEMP -30 #define CONFIG_SYS_DTT_HYSTERESIS 3 #ifndef CONFIG_PCIE1 /* RapidIO MMU */ #ifdef CONFIG_TQM_BIGFLASH #define CONFIG_SYS_RIO_MEM_BASE 0xb0000000 /* base address */ #define CONFIG_SYS_RIO_MEM_SIZE 0x10000000 /* 256M */ #else /* !CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */ #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 512M */ #endif /* CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE #endif /* CONFIG_PCIE1 */ /* NAND FLASH */ #ifdef CONFIG_NAND #undef CONFIG_NAND_LEGACY #define CONFIG_NAND_FSL_UPM 1 #define CONFIG_MTD_NAND_ECC_JFFS2 1 /* use JFFS2 ECC */ /* address distance between chip selects */ #define CONFIG_SYS_NAND_SELECT_DEVICE 1 #define CONFIG_SYS_NAND_CS_DIST 0x200 #define CONFIG_SYS_NAND_SIZE 0x8000 #define CONFIG_SYS_NAND0_BASE (CONFIG_SYS_CCSRBAR + 0x03010000) #define CONFIG_SYS_NAND1_BASE (CONFIG_SYS_NAND0_BASE + CONFIG_SYS_NAND_CS_DIST) #define CONFIG_SYS_NAND2_BASE (CONFIG_SYS_NAND1_BASE + CONFIG_SYS_NAND_CS_DIST) #define CONFIG_SYS_NAND3_BASE (CONFIG_SYS_NAND2_BASE + CONFIG_SYS_NAND_CS_DIST) #define CONFIG_SYS_MAX_NAND_DEVICE 2 /* Max number of NAND devices */ #define NAND_MAX_CHIPS 1 #if (CONFIG_SYS_MAX_NAND_DEVICE == 1) #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE } #elif (CONFIG_SYS_MAX_NAND_DEVICE == 2) #define CONFIG_SYS_NAND_QUIET_TEST 1 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE, \ CONFIG_SYS_NAND1_BASE, \ } #elif (CONFIG_SYS_MAX_NAND_DEVICE == 4) #define CONFIG_SYS_NAND_QUIET_TEST 1 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE, \ CONFIG_SYS_NAND1_BASE, \ CONFIG_SYS_NAND2_BASE, \ CONFIG_SYS_NAND3_BASE, \ } #endif /* CS3 for NAND Flash */ #define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_NAND0_BASE & BR_BA) | BR_PS_8 | \ BR_MS_UPMB | BR_V) #define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_NAND_SIZE) | OR_UPM_BI) #define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */ #endif /* CONFIG_NAND */ /* * General PCI * Addresses are mapped 1-1. */ #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCI1_IO_BASE (CONFIG_SYS_CCSRBAR + 0x02000000) #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE #define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */ #ifdef CONFIG_PCIE1 /* * General PCI express * Addresses are mapped 1-1. */ #ifdef CONFIG_TQM_BIGFLASH #define CONFIG_SYS_PCIE1_MEM_BASE 0xb0000000 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 512M */ #define CONFIG_SYS_PCIE1_IO_BASE 0xaf000000 #else /* !CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_PCIE1_MEM_BASE 0xc0000000 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE1_IO_BASE 0xef000000 #endif /* CONFIG_TQM_BIGFLASH */ #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE #define CONFIG_SYS_PCIE1_IO_PHYS CONFIG_SYS_PCIE1_IO_BASE #define CONFIG_SYS_PCIE1_IO_SIZE 0x1000000 /* 16M */ #endif /* CONFIG_PCIE1 */ #if defined(CONFIG_PCI) #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_EEPRO100 #undef CONFIG_TULIP #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ #endif /* CONFIG_PCI */ #define CONFIG_NET_MULTI 1 #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_TSEC1 1 #define CONFIG_TSEC1_NAME "TSEC0" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define TSEC1_FLAGS TSEC_GIGABIT #define TSEC2_FLAGS TSEC_GIGABIT #define FEC_PHY_ADDR 3 #define FEC_PHYIDX 0 #define FEC_FLAGS 0 #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 #ifdef CONFIG_TQM8548 /* * TQM8548 has 4 ethernet ports. 4 ETSEC's. * * On the STK85xx Starterkit the ETSEC3/4 ports are on an * additional adapter (AIO) between module and Starterkit. */ #define CONFIG_TSEC3 1 #define CONFIG_TSEC3_NAME "TSEC2" #define CONFIG_TSEC4 1 #define CONFIG_TSEC4_NAME "TSEC3" #define TSEC3_PHY_ADDR 4 #define TSEC4_PHY_ADDR 5 #define TSEC3_PHYIDX 0 #define TSEC4_PHYIDX 0 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define CONFIG_HAS_ETH3 #define CONFIG_HAS_ETH4 #endif /* CONFIG_TQM8548 */ /* Options are TSEC[0-1], FEC */ #define CONFIG_ETHPRIME "TSEC0" #if defined(CONFIG_TQM8540) /* * TQM8540 has 3 ethernet ports. 2 TSEC's and one FEC. * The FEC port is connected on the same signals as the FCC3 port * of the TQM8560 to the baseboard (STK85xx Starterkit). * * On the STK85xx Starterkit the X47/X50 jumper has to be set to * a - d (X50.2 - 3) to enable the FEC port. */ #define CONFIG_MPC85XX_FEC 1 #define CONFIG_MPC85XX_FEC_NAME "FEC" #endif #if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) /* * TQM8541/55 have 4 ethernet ports. 2 TSEC's and 2 FCC's. Only one FCC port * can be used at once, since only one FCC port is available on the STK85xx * Starterkit. * * To use this port you have to configure U-Boot to use the FCC port 1...2 * and set the X47/X50 jumper to: * FCC1: a - b (X47.2 - X50.2) * FCC2: a - c (X50.2 - 1) */ #define CONFIG_ETHER_ON_FCC #define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */ #endif #if defined(CONFIG_TQM8560) /* * TQM8560 has 5 ethernet ports. 2 TSEC's and 3 FCC's. Only one FCC port * can be used at once, since only one FCC port is available on the STK85xx * Starterkit. * * To use this port you have to configure U-Boot to use the FCC port 1...3 * and set the X47/X50 jumper to: * FCC1: a - b (X47.2 - X50.2) * FCC2: a - c (X50.2 - 1) * FCC3: a - d (X50.2 - 3) */ #define CONFIG_ETHER_ON_FCC #define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */ #endif #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1) #define CONFIG_ETHER_ON_FCC1 #define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | \ CMXFCR_TF1CS_MSK) #define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12) #define CONFIG_SYS_CPMFCR_RAMTYPE 0 #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) #endif #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) #define CONFIG_ETHER_ON_FCC2 #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | \ CMXFCR_TF2CS_MSK) #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13) #define CONFIG_SYS_CPMFCR_RAMTYPE 0 #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) #endif #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3) #define CONFIG_ETHER_ON_FCC3 #define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | \ CMXFCR_TF3CS_MSK) #define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14) #define CONFIG_SYS_CPMFCR_RAMTYPE 0 #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) #endif /* * Environment */ #define CONFIG_ENV_IS_IN_FLASH 1 #ifdef CONFIG_TQM_FLASH_N_TYPE #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K (one sector) for env */ #else /* !CONFIG_TQM_FLASH_N_TYPE */ #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */ #endif /* CONFIG_TQM_FLASH_N_TYPE */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_TIMESTAMP /* Print image info with ts */ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #ifdef CONFIG_NAND /* * Use NAND-FLash as JFFS2 device */ #define CONFIG_CMD_NAND #define CONFIG_CMD_JFFS2 #define CONFIG_JFFS2_NAND 1 #ifdef CONFIG_JFFS2_CMDLINE #define MTDIDS_DEFAULT "nand0=TQM85xx-nand" #define MTDPARTS_DEFAULT "mtdparts=TQM85xx-nand:-" #else #define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */ #define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ #define CONFIG_JFFS2_PART_SIZE 0x200000 /* size of jffs2 partition */ #endif /* CONFIG_JFFS2_CMDLINE */ #endif /* CONFIG_NAND */ /* * Command line configuration. */ #include <config_cmd_default.h> #define CONFIG_CMD_PING #define CONFIG_CMD_I2C #define CONFIG_CMD_DHCP #define CONFIG_CMD_NFS #define CONFIG_CMD_SNTP #define CONFIG_CMD_DATE #define CONFIG_CMD_EEPROM #define CONFIG_CMD_DTT #define CONFIG_CMD_MII #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI #endif #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buf Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif #define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ #define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ #define CONFIG_PREBOOT "echo;" \ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ "echo" #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ /* * Setup some board specific values for the default environment variables */ #ifdef CONFIG_CPM2 #define CONFIG_ENV_CONSDEV "consdev=ttyCPM0\0" #else #define CONFIG_ENV_CONSDEV "consdev=ttyS0\0" #endif #define CONFIG_ENV_FDT_FILE "fdt_file="MK_STR(CONFIG_HOSTNAME)"/" \ MK_STR(CONFIG_HOSTNAME)".dtb\0" #define CONFIG_ENV_BOOTFILE "bootfile="MK_STR(CONFIG_HOSTNAME)"/uImage\0" #define CONFIG_ENV_UBOOT "uboot="MK_STR(CONFIG_HOSTNAME)"/u-boot.bin\0" \ "uboot_addr="MK_STR(TEXT_BASE)"\0" #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_ENV_BOOTFILE \ CONFIG_ENV_FDT_FILE \ CONFIG_ENV_CONSDEV \ "netdev=eth0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs $bootargs " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ ":$hostname:$netdev:off panic=1\0" \ "addcons=setenv bootargs $bootargs " \ "console=$consdev,$baudrate\0" \ "flash_nfs=run nfsargs addip addcons;" \ "bootm $kernel_addr - $fdt_addr\0" \ "flash_self=run ramargs addip addcons;" \ "bootm $kernel_addr $ramdisk_addr $fdt_addr\0" \ "net_nfs=tftp $kernel_addr_r $bootfile;" \ "tftp $fdt_addr_r $fdt_file;" \ "run nfsargs addip addcons;" \ "bootm $kernel_addr_r - $fdt_addr_r\0" \ "rootpath=/opt/eldk/ppc_85xx\0" \ "fdt_addr_r=900000\0" \ "kernel_addr_r=1000000\0" \ "fdt_addr=ffec0000\0" \ "kernel_addr=ffd00000\0" \ "ramdisk_addr=ff800000\0" \ CONFIG_ENV_UBOOT \ "load=tftp 100000 $uboot\0" \ "update=protect off $uboot_addr +$filesize;" \ "erase $uboot_addr +$filesize;" \ "cp.b 100000 $uboot_addr $filesize;" \ "setenv filesize;saveenv\0" \ "upd=run load update\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" #endif /* __CONFIG_H */