/* * Copyright 2005 DENX Software Engineering * Wolfgang Denk <wd@denx.de> * Copyright 2004 Freescale Semiconductor. * (C) Copyright 2002,2003 Motorola,Inc. * Xianghua Xiao <X.Xiao@motorola.com> * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * TQM8540 board configuration file * * Make sure you change the MAC address and other network params first, * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. */ #ifndef __CONFIG_H #define __CONFIG_H /* High Level Configuration Options */ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ #define CONFIG_MPC8540 1 /* MPC8540 specific */ #define CONFIG_TQM8540 1 /* TQM8540 board specific */ #undef CONFIG_PCI #define CONFIG_TSEC_ENET /* tsec ethernet support */ #undef CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ /* * sysclk for MPC85xx * * Two valid values are: * 33000000 * 66000000 * * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz * is likely the desired value here, so that is now the default. * The board, however, can run at 66MHz. In any event, this value * must match the settings of some switches. Details can be found * in the README.mpc85xxads. */ #ifndef CONFIG_SYS_CLK_FREQ #define CONFIG_SYS_CLK_FREQ 33000000 #endif /* * These can be toggled for performance analysis, otherwise use default. */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00000000 /* memtest region */ #define CFG_MEMTEST_END 0x10000000 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ #define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ #define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ /* * DDR Setup */ #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE #if defined(CONFIG_SPD_EEPROM) /* * Determine DDR configuration from I2C interface. */ #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ #else /* * Manually set up DDR parameters */ #define CFG_SDRAM_SIZE 512 /* DDR is 256MB */ #define CFG_DDR_CS0_BNDS 0x0000001f /* 0-256MB */ #define CFG_DDR_CS0_CONFIG 0x80000102 #define CFG_DDR_TIMING_1 0x47445331 #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ #define CFG_DDR_MODE 0x40020062 /* DLL,normal,seq,4/2.5 */ #define CFG_DDR_INTERVAL 0x05160100 /* autocharge,no open page */ #endif /* * Flash on the Local Bus */ #define CFG_LBC_FLASH_BASE 0xfe000000 /* Localbus SDRAM */ #define CFG_LBC_FLASH_SIZE 32 /* LBC SDRAM is 32MB */ #define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH 32M */ #define CFG_BR0_PRELIM 0xfe001801 /* port size 32bit */ #define CFG_OR0_PRELIM 0xfe000040 /* 32MB Flash */ #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ #define CFG_MAX_FLASH_SECT 256 /* sectors per device */ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) #define CFG_RAMBOOT #else #undef CFG_RAMBOOT #endif #define CFG_FLASH_CFI_DRIVER #define CFG_FLASH_CFI #define CFG_FLASH_EMPTY_INFO #define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ #define CFG_LBC_LBCR 0x00000000 /* LB config reg */ #define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ #define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ /* * LSDMR masks */ #define CFG_LBC_LSDMR_RFEN (1 << (31 - 1)) #define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) #define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) #define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16)) #define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16)) #define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19)) #define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) #define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22)) #define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) #define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) #define CFG_LBC_LSDMR_BL8 (1 << (31 - 23)) #define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27)) #define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27)) #define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29)) #define CFG_LBC_LSDMR_CL3 (3 << (31 - 31)) #define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) #define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) #define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) #define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) #define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) #define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) #define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) #define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) #define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_BSMA1516 \ | CFG_LBC_LSDMR_RFCR5 \ | CFG_LBC_LSDMR_PRETOACT3 \ | CFG_LBC_LSDMR_ACTTORW3 \ | CFG_LBC_LSDMR_BL8 \ | CFG_LBC_LSDMR_WRC2 \ | CFG_LBC_LSDMR_CL3 \ | CFG_LBC_LSDMR_RFEN \ ) /* * SDRAM Controller configuration sequence. */ #define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_PCHALL) #define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_ARFRSH) #define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_ARFRSH) #define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_MRW) #define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_NORMAL) #define CONFIG_L1_INIT_RAM #define CFG_INIT_RAM_LOCK 1 #define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ #define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_NS16550 #define CFG_NS16550_SERIAL #define CFG_NS16550_REG_SIZE 1 #define CFG_NS16550_CLK get_bus_freq(0) #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} #define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) #define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) /* Use the HUSH parser */ #define CFG_HUSH_PARSER #ifdef CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " #endif /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ /* RapidIO MMU */ #define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ #define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE #define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ /* * General PCI * Addresses are mapped 1-1. */ #define CFG_PCI1_MEM_BASE 0x80000000 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ #define CFG_PCI1_IO_BASE 0xe2000000 #define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE #define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ #if defined(CONFIG_PCI) #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ #undef CONFIG_EEPRO100 #undef CONFIG_TULIP #if !defined(CONFIG_PCI_PNP) #define PCI_ENET0_IOADDR 0xe0000000 #define PCI_ENET0_MEMADDR 0xe0000000 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ #endif #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ #endif /* CONFIG_PCI */ #if defined(CONFIG_TSEC_ENET) #ifndef CONFIG_NET_MULTI #define CONFIG_NET_MULTI 1 #endif #define CONFIG_MII 1 /* MII PHY management */ #undef CONFIG_MPC85XX_TSEC1 #define CONFIG_MPC85XX_TSEC2 1 #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #undef CONFIG_MPC85XX_FEC #define FEC_PHY_ADDR 0 #define FEC_PHYIDX 0 #define CONFIG_ETHPRIME "ENET1" #endif /* CONFIG_TSEC_ENET */ /* * Environment */ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000) #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ #define CFG_ENV_SIZE 0x2000 #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #else #define CFG_NO_FLASH 1 /* Flash is not usable now */ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) #define CFG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_TIMESTAMP /* Print image info with timestamp */ #if defined(CFG_RAMBOOT) # define CONFIG_CMD_PRIV (CONFIG_CMD_DFL & ~(CFG_CMD_ENV | CFG_CMD_LOADS)) #else # define CONFIG_CMD_PRIV (CONFIG_CMD_DFL | \ CFG_CMD_DHCP | \ CFG_CMD_NFS | \ CFG_CMD_SNTP ) #endif #if defined(CONFIG_PCI) # define ADD_PCI_CMD (CFG_CMD_PCI) #else # define ADD_PCI_CMD 0 #endif #define CONFIG_COMMANDS (CONFIG_CMD_PRIV | \ ADD_PCI_CMD | \ CFG_CMD_PING | \ CFG_CMD_I2C ) #include <cmd_confdefs.h> #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ #define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ #define CONFIG_BAUDRATE 115200 #define CONFIG_PREBOOT "echo;" \ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ "echo" #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "consdev=ttyS0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs $bootargs " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ ":$hostname:$netdev:off panic=1\0" \ "addcons=setenv bootargs $bootargs " \ "console=$consdev,$baudrate\0" \ "flash_nfs=run nfsargs addip addcons;" \ "bootm $kernel_addr\0" \ "flash_self=run ramargs addip addcons;" \ "bootm $kernel_addr $ramdisk_addr\0" \ "net_nfs=tftp $loadaddr $bootfile;" \ "run nfsargs addip addcons;bootm\0" \ "rootpath=/opt/eldk/ppc_85xx\0" \ "bootfile=/tftpboot/tqm8540/uImage\0" \ "kernel_addr=FE000000\0" \ "ramdisk_addr=FE100000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" #endif /* __CONFIG_H */