/* * Configuation settings for the esd TASREG board. * * (C) Copyright 2004 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * board/config.h - configuration options, board specific */ #ifndef _TASREG_H #define _TASREG_H #ifndef __ASSEMBLY__ #include <asm/m5249.h> #endif /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MCF52x2 /* define processor family */ #define CONFIG_M5249 /* define processor type */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ #define CONFIG_MCFTMR #define CONFIG_MCFUART #define CONFIG_SYS_UART_PORT (0) #define CONFIG_BAUDRATE 19200 #undef CONFIG_WATCHDOG #undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include <config_cmd_default.h> #define CONFIG_CMD_BSP #define CONFIG_CMD_EEPROM #define CONFIG_CMD_I2C #undef CONFIG_CMD_NET #define CONFIG_BOOTDELAY 3 #define CONFIG_SYS_PROMPT "=> " #define CONFIG_SYS_LONGHELP /* undef to save memory */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ #define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ #define CONFIG_LOOPW 1 /* enable loopw command */ #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */ #define CONFIG_SYS_MEMTEST_START 0x400 #define CONFIG_SYS_MEMTEST_END 0x380000 #define CONFIG_SYS_HZ 1000 /* * Clock configuration: enable only one of the following options */ #if 0 /* this setting will run the cpu at 11MHz */ #define CONFIG_SYS_PLL_BYPASS 1 /* bypass PLL for test purpose */ #undef CONFIG_SYS_FAST_CLK /* MCF5249 can run at 140MHz */ #define CONFIG_SYS_CLK 11289600 /* PLL bypass */ #endif #if 0 /* this setting will run the cpu at 70MHz */ #undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ #undef CONFIG_SYS_FAST_CLK /* MCF5249 can run at 140MHz */ #define CONFIG_SYS_CLK 72185018 /* The next lower speed */ #endif #if 1 /* this setting will run the cpu at 140MHz */ #undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ #define CONFIG_SYS_FAST_CLK 1 /* MCF5249 can run at 140MHz */ #define CONFIG_SYS_CLK 132025600 /* MCF5249 can run at 140MHz */ #endif /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ #define CONFIG_SYS_MBAR2 0x80000000 /*----------------------------------------------------------------------- * I2C */ #define CONFIG_SOFT_I2C #define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ /* 32 byte page write mode using*/ /* last 5 bits of the address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #if defined (CONFIG_SOFT_I2C) #if 0 /* push-pull */ #define SDA 0x00800000 #define SCL 0x00000008 #define DIR0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_EN)) #define DIR1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_EN)) #define OUT0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_OUT)) #define OUT1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_OUT)) #define IN0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_READ)) #define IN1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_READ)) #define I2C_INIT {OUT1|=SDA;OUT0|=SCL;} #define I2C_READ ((IN1&SDA)?1:0) #define I2C_SDA(x) {if(x)OUT1|=SDA;else OUT1&=~SDA;} #define I2C_SCL(x) {if(x)OUT0|=SCL;else OUT0&=~SCL;} #define I2C_DELAY {udelay(5);} #define I2C_ACTIVE {DIR1|=SDA;} #define I2C_TRISTATE {DIR1&=~SDA;} #else /* open-collector */ #define SDA 0x00800000 #define SCL 0x00000008 #define DIR0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_EN)) #define DIR1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_EN)) #define OUT0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_OUT)) #define OUT1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_OUT)) #define IN0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_READ)) #define IN1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_READ)) #define I2C_INIT {DIR1&=~SDA;DIR0&=~SCL;OUT1&=~SDA;OUT0&=~SCL;} #define I2C_READ ((IN1&SDA)?1:0) #define I2C_SDA(x) {if(x)DIR1&=~SDA;else DIR1|=SDA;} #define I2C_SCL(x) {if(x)DIR0&=~SCL;else DIR0|=SCL;} #define I2C_DELAY {udelay(5);} #define I2C_ACTIVE {DIR1|=SDA;} #define I2C_TRISTATE {DIR1&=~SDA;} #endif #endif /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_ADDR 0xFFC40000 /* Address of Environment Sector*/ #define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ #define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE #if 0 /* test-only */ #define CONFIG_PRAM 512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */ #endif #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) #define CONFIG_SYS_MONITOR_LEN 0x20000 #define CONFIG_SYS_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */ #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ #define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ #define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ /* * The following defines are added for buggy IOP480 byte interface. * All other boards should use the standard values (CPCI405 etc.) */ #define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ #define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ #define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 8) #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 4) #define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) #define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ CF_ACR_EN | CF_ACR_SM_ALL) #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ CF_CACR_DBWE) /*----------------------------------------------------------------------- * Memory bank definitions */ /* CS0 - AMD Flash, address 0xffc00000 */ #define CONFIG_SYS_CS0_BASE 0xffc00000 #define CONFIG_SYS_CS0_CTRL 0x00001980 /* WS=0110, AA=1, PS=10 */ /** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/ #define CONFIG_SYS_CS0_MASK 0x003f0021 /* 4MB, AA=0, WP=0, C/I=1, V=1 */ /* CS1 - FPGA, address 0xe0000000 */ #define CONFIG_SYS_CS1_BASE 0xe0000000 #define CONFIG_SYS_CS1_CTRL 0x00000d80 /* WS=0011, AA=1, PS=10 */ #define CONFIG_SYS_CS1_MASK 0x00010001 /* 128kB, AA=0, WP=0, C/I=0, V=1*/ /*----------------------------------------------------------------------- * Port configuration */ #define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ #define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54*/ #define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ #define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ #define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ #define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ #define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ /*----------------------------------------------------------------------- * FPGA stuff */ #define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ #define CONFIG_SYS_FPGA_MAX_SIZE 512*1024 /* 512kByte is enough for XC2S200*/ /* FPGA program pin configuration */ #define CONFIG_SYS_FPGA_PRG 0x00010000 /* FPGA program pin (ppc output) */ #define CONFIG_SYS_FPGA_CLK 0x00040000 /* FPGA clk pin (ppc output) */ #define CONFIG_SYS_FPGA_DATA 0x00020000 /* FPGA data pin (ppc output) */ #define CONFIG_SYS_FPGA_INIT 0x00080000 /* FPGA init pin (ppc input) */ #define CONFIG_SYS_FPGA_DONE 0x00100000 /* FPGA done pin (ppc input) */ #endif /* _TASREG_H */