/* * (C) Copyright 2000 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC823 1 /* This is a MPC823 CPU */ #define CONFIG_SPD823TS 1 /* ...on a SPD823TS board */ #define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ #undef CONFIG_8xx_CONS_SMC2 #undef CONFIG_8xx_CONS_NONE #define CONFIG_BAUDRATE 115200 #if 0 #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ #else #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #endif #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ #define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ #define CONFIG_BOOTARGS "root=/dev/nfs rw " \ "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \ "nfsaddrs=10.0.0.99:10.0.0.2" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Command line configuration. */ #include <config_cmd_default.h> #define CONFIG_CMD_IDE #undef CONFIG_CMD_SAVEENV #undef CONFIG_CMD_FLASH #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE /*----------------------------------------------------------------------*/ #define CONFIG_ETHADDR 00:D0:93:00:01:CB #define CONFIG_IPADDR 10.0.0.98 #define CONFIG_SERVERIP 10.0.0.1 #undef CONFIG_BOOTCOMMAND #define CONFIG_BOOTCOMMAND "tftp 200000 uImage;bootm 200000" /*----------------------------------------------------------------------*/ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ #define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ #define CONFIG_SYS_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ #define CONFIG_SYS_IMMR 0xFFF00000 /* was: 0xFF000000 */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR #define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFF000000 #ifdef DEBUG #define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ #else #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #endif #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 0 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 0 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 0 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 0 /* Timeout for Flash Write (in ms) */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ #define CONFIG_ENV_SIZE 0x0800 /* Total Size of Environment Sector */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #if defined(CONFIG_WATCHDOG) #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) #else #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) #endif /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 11-6 *----------------------------------------------------------------------- * PCMCIA config., multi-function pin tri-state */ /* 0x00000040 */ #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC00 | SIUMCR_GB5E) /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 11-31 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled */ #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) /*----------------------------------------------------------------------- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 *----------------------------------------------------------------------- * Reset PLL lock status sticky bit, timer expired status bit and timer * interrupt status bit, set PLL multiplication factor ! */ /* 0x00b0c0c0 */ #define CONFIG_SYS_PLPRCR \ ( (11 << PLPRCR_MF_SHIFT) | \ PLPRCR_SPLSS | PLPRCR_TEXPS | /*PLPRCR_TMIST|*/ \ /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \ ) /*----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register 15-27 *----------------------------------------------------------------------- * Set clock output, timebase and RTC source and divider, * power management and some other internal clocks */ #define SCCR_MASK SCCR_EBDF11 /* 0x01800014 */ #define CONFIG_SYS_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \ SCCR_RTDIV | SCCR_RTSEL | \ /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ SCCR_EBDF00 | SCCR_DFSYNC00 | \ SCCR_DFBRG00 | SCCR_DFNL000 | \ SCCR_DFNH000 | SCCR_DFLCD101 | \ SCCR_DFALCD00) /*----------------------------------------------------------------------- * RTCSC - Real-Time Clock Status and Control Register *----------------------------------------------------------------------- */ /* 0x00C3 */ #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) /*----------------------------------------------------------------------- * RCCR - RISC Controller Configuration Register *----------------------------------------------------------------------- */ /* TIMEP=2 */ #define CONFIG_SYS_RCCR 0x0200 /*----------------------------------------------------------------------- * RMDS - RISC Microcode Development Support Control Register *----------------------------------------------------------------------- */ #define CONFIG_SYS_RMDS 0 /*----------------------------------------------------------------------- * SDSR - SDMA Status Register *----------------------------------------------------------------------- */ #define CONFIG_SYS_SDSR ((u_char)0x83) /*----------------------------------------------------------------------- * SDMR - SDMA Mask Register *----------------------------------------------------------------------- */ #define CONFIG_SYS_SDMR ((u_char)0x00) /*----------------------------------------------------------------------- * * Interrupt Levels *----------------------------------------------------------------------- */ #define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ /*----------------------------------------------------------------------- * PCMCIA stuff *----------------------------------------------------------------------- * */ #define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) #define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) #define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) #define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) #define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) #define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) #define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) #define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) /*----------------------------------------------------------------------- * IDE/ATA stuff *----------------------------------------------------------------------- */ #define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */ #define CONFIG_IDE_LED 1 /* LED for ide supported */ #define CONFIG_IDE_RESET 1 /* reset for ide supported */ #define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */ #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ #define CONFIG_SYS_ATA_BASE_ADDR 0xFE100000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 #define CONFIG_SYS_ATA_IDE1_OFFSET 0x0C00 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ #define CONFIG_SYS_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */ /*----------------------------------------------------------------------- * *----------------------------------------------------------------------- * */ #define CONFIG_SYS_DER 0 /* * Init Memory Controller: * * BR0/1 and OR0/1 (FLASH) */ #define FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank #0 */ #define FLASH_BASE1_PRELIM 0xFF080000 /* FLASH bank #1 */ /* used to re-map FLASH both when starting from SRAM or FLASH: * restrict access enough to keep SRAM working (if any) * but not too much to meddle with FLASH accesses */ /* EPROMs are 512kb */ #define CONFIG_SYS_REMAP_OR_AM 0xFFF80000 /* OR addr mask */ #define CONFIG_SYS_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */ /* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ #define CONFIG_SYS_OR_TIMING_FLASH (/* OR_CSNT_SAM | */ OR_ACS_DIV4 | OR_BI | \ OR_SCY_5_CLK | OR_EHTR) #define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 16 bit, bank valid */ #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) #define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM /* 16 bit, bank valid */ #define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) /* * BR2-5 and OR2-5 (SRAM/SDRAM/PER8/SHARC) * */ #define SRAM_BASE 0xFE200000 /* SRAM bank */ #define SRAM_OR_AM 0xFFE00000 /* SRAM is 2 MB */ #define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */ #define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ #define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ #define PER8_BASE 0xFE000000 /* PER8 bank */ #define PER8_OR_AM 0xFFF00000 /* PER8 is 1 MB */ #define SHARC_BASE 0xFE400000 /* SHARC bank */ #define SHARC_OR_AM 0xFFC00000 /* SHARC is 4 MB */ /* SRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ #define CONFIG_SYS_OR_TIMING_SRAM 0x00000D42 /* SRAM-Timing */ #define CONFIG_SYS_OR2 (SRAM_OR_AM | CONFIG_SYS_OR_TIMING_SRAM ) #define CONFIG_SYS_BR2 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V ) /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ #define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 /* SDRAM-Timing */ #define CONFIG_SYS_OR3_PRELIM (SDRAM_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM ) #define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V ) #define CONFIG_SYS_OR_TIMING_PER8 0x00000F32 /* PER8-Timing */ #define CONFIG_SYS_OR4 (PER8_OR_AM | CONFIG_SYS_OR_TIMING_PER8 ) #define CONFIG_SYS_BR4 ((PER8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) #define CONFIG_SYS_OR_TIMING_SHARC 0x00000700 /* SHARC-Timing */ #define CONFIG_SYS_OR5 (SHARC_OR_AM | CONFIG_SYS_OR_TIMING_SHARC ) #define CONFIG_SYS_BR5 ((SHARC_BASE & BR_BA_MSK) | BR_PS_32 | BR_MS_UPMA | BR_V ) /* * Memory Periodic Timer Prescaler */ /* periodic timer for refresh */ #define CONFIG_SYS_MBMR_PTB 204 /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ #define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ #define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ /* * MBMR settings for SDRAM */ /* 8 column SDRAM */ #define CONFIG_SYS_MBMR_8COL ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \ MBMR_AMB_TYPE_0 | MBMR_DSB_1_CYCL | MBMR_G0CLB_A11 | \ MBMR_RLFB_1X | MBMR_WLFB_1X | MBMR_TLFB_4X) /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #endif /* __CONFIG_H */