/* * (C) Copyright 2000, 2001, 2002 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * SPDX-License-Identifier: GPL-2.0+ */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC823 1 /* This is a MPC823 CPU */ #define CONFIG_RRVISION 1 /* ...on a RRvision board */ #define CONFIG_SYS_TEXT_BASE 0x40000000 #define CONFIG_8xx_GCLK_FREQ 64000000 #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ #undef CONFIG_8xx_CONS_SMC2 #undef CONFIG_8xx_CONS_NONE #define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ #if 0 #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ #else #define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ #endif #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ #define CONFIG_PREBOOT "setenv stdout serial" #undef CONFIG_BOOTARGS #define CONFIG_ETHADDR 00:50:C2:00:E0:70 #define CONFIG_OVERWRITE_ETHADDR_ONCE 1 #define CONFIG_IPADDR 10.0.0.5 #define CONFIG_SERVERIP 10.0.0.2 #define CONFIG_NETMASK 255.0.0.0 #define CONFIG_ROOTPATH "/opt/eldk/ppc_8xx" #define CONFIG_BOOTCOMMAND "run flash_self" #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}" \ ":${gatewayip}:${netmask}:${hostname}:${netdev}:off\0" \ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ "load=tftp 100000 /tftpboot/u-boot.bin\0" \ "update=protect off 1:0-8;era 1:0-8;" \ "cp.b 100000 40000000 ${filesize};" \ "setenv filesize;saveenv\0" \ "kernel_addr=40040000\0" \ "ramdisk_addr=40100000\0" \ "kernel_img=/tftpboot/uImage\0" \ "kernel_load=tftp 200000 ${kernel_img}\0" \ "net_nfs=run kernel_load nfsargs addip addtty;bootm\0" \ "flash_nfs=run nfsargs addip addtty;bootm ${kernel_addr}\0" \ "flash_self=run ramargs addip addtty;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #undef CONFIG_WATCHDOG /* watchdog disabled */ #undef CONFIG_STATUS_LED /* disturbs display */ #undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION #define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ #ifdef CONFIG_LCD #define CONFIG_MPC8XX_LCD #else #define CONFIG_VIDEO 1 /* To enable the video initialization */ /* Video related */ #define CONFIG_VIDEO_LOGO 1 /* Show the logo */ #define CONFIG_VIDEO_ENCODER_AD7179 1 /* Enable this encoder */ #define CONFIG_VIDEO_ENCODER_AD7179_ADDR 0x2A /* ALSB to ground */ #endif /* enable I2C and select the hardware/software driver */ #undef CONFIG_HARD_I2C /* I2C with hardware support */ #define CONFIG_SOFT_I2C /* I2C bit-banged */ # define CONFIG_SYS_I2C_SPEED 50000 /* 50 kHz is supposed to work */ # define CONFIG_SYS_I2C_SLAVE 0xFE #ifdef CONFIG_SOFT_I2C /* * Software (bit-bang) I2C driver configuration */ #define PB_SCL 0x00000020 /* PB 26 */ #define PB_SDA 0x00000010 /* PB 27 */ #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) #define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ else immr->im_cpm.cp_pbdat &= ~PB_SDA #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(1) /* 1/4 I2C clock duration */ #endif /* CONFIG_SOFT_I2C */ /* * Command line configuration. */ #include #define CONFIG_CMD_DHCP #define CONFIG_CMD_I2C #define CONFIG_CMD_IDE #define CONFIG_CMD_DATE #undef CONFIG_CMD_PCMCIA #undef CONFIG_CMD_IDE /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ #define CONFIG_SYS_IMMR 0xFFF00000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR #define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0x40000000 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ /* timeout values are in ticks = ms */ #define CONFIG_SYS_FLASH_ERASE_TOUT (120*CONFIG_SYS_HZ) /* Timeout for Flash Erase */ #define CONFIG_SYS_FLASH_WRITE_TOUT (1 * CONFIG_SYS_HZ) /* Timeout for Flash Write */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ #define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #if defined(CONFIG_WATCHDOG) #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) #else #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) #endif /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 11-6 *----------------------------------------------------------------------- * PCMCIA config., multi-function pin tri-state */ #ifndef CONFIG_CAN_DRIVER #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) #else /* we must activate GPL5 in the SIUMCR for CAN */ #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) #endif /* CONFIG_CAN_DRIVER */ /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) /*----------------------------------------------------------------------- * RTCSC - Real-Time Clock Status and Control Register 11-27 *----------------------------------------------------------------------- */ #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 11-31 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled */ #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) /*----------------------------------------------------------------------- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 *----------------------------------------------------------------------- * Reset PLL lock status sticky bit, timer expired status bit and timer * interrupt status bit */ /* for 64 MHz, we use a 16 MHz clock * 4 */ #define CONFIG_SYS_PLPRCR ( (4-1)< ms * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration * 4 Number of refresh cycles per period * 64 Refresh cycle in ms per number of rows * -------------------------------------------- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 * * 50 MHz => 50.000.000 / Divider = 98 * 66 Mhz => 66.000.000 / Divider = 129 * 80 Mhz => 80.000.000 / Divider = 156 */ #define CONFIG_SYS_MAMR_PTA 129 /* * For 16 MBit, refresh rates could be 31.3 us * (= 64 ms / 2K = 125 / quad bursts). * For a simpler initialization, 15.6 us is used instead. * * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank */ #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ #define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ #define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ /* * MAMR settings for SDRAM */ /* 8 column SDRAM */ #define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) /* 9 column SDRAM */ #define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) #endif /* __CONFIG_H */