/* * (C) Copyright 2000 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * Pantelis Antoniou, Intracom S.A., panto@intracom.gr * U-Boot port on NetVia board */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MPC850 1 /* This is a MPC850 CPU */ #define CONFIG_NETVIA 1 /* ...on a NetVia board */ #if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1 #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ #undef CONFIG_8xx_CONS_SMC2 #undef CONFIG_8xx_CONS_NONE #else #define CONFIG_8xx_CONS_NONE #define CONFIG_MAX3100_SERIAL #endif #define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ #define CONFIG_XIN 10000000 #define CONFIG_8xx_GCLK_FREQ 80000000 #if 0 #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ #else #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #endif #undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */ #define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" #undef CONFIG_BOOTARGS #define CONFIG_BOOTCOMMAND \ "tftpboot; " \ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ "bootm" #define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_STATUS_LED 1 /* Status LED enabled */ #if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 #define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ #endif #undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_NISDOMAIN #undef CONFIG_MAC_PARTITION #undef CONFIG_DOS_PARTITION #define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ /* * Command line configuration. */ #include <config_cmd_default.h> #define CONFIG_CMD_DHCP #define CONFIG_CMD_PING #if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 /* #define CONFIG_CMD_NAND */ /* disabled */ #endif #define CONFIG_BOARD_EARLY_INIT_F 1 #define CONFIG_MISC_INIT_R /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0300000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ #define CONFIG_SYS_IMMR 0xFF000000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR #define CONFIG_SYS_INIT_RAM_END 0x3000 /* End of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0x40000000 #if defined(DEBUG) #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #else #define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ #endif #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_SECT_SIZE 0x10000 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000) #define CONFIG_ENV_OFFSET 0 #define CONFIG_ENV_SIZE 0x4000 #define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x70000) #define CONFIG_ENV_OFFSET_REDUND 0 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #if defined(CONFIG_WATCHDOG) #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) #else #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) #endif /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 11-6 *----------------------------------------------------------------------- * PCMCIA config., multi-function pin tri-state */ #ifndef CONFIG_CAN_DRIVER #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) #else /* we must activate GPL5 in the SIUMCR for CAN */ #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) #endif /* CONFIG_CAN_DRIVER */ /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) /*----------------------------------------------------------------------- * RTCSC - Real-Time Clock Status and Control Register 11-27 *----------------------------------------------------------------------- */ #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 11-31 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled */ #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) /*----------------------------------------------------------------------- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 *----------------------------------------------------------------------- * Reset PLL lock status sticky bit, timer expired status bit and timer * interrupt status bit * * *----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register 15-27 *----------------------------------------------------------------------- * Set clock output, timebase and RTC source and divider, * power management and some other internal clocks */ #define SCCR_MASK SCCR_EBDF11 #if CONFIG_8xx_GCLK_FREQ == 50000000 #define CONFIG_SYS_PLPRCR ( ((5 - 1) << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) #define CONFIG_SYS_SCCR (SCCR_TBS | \ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ SCCR_DFALCD00) #elif CONFIG_8xx_GCLK_FREQ == 80000000 #define CONFIG_SYS_PLPRCR ( ((8 - 1) << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) #define CONFIG_SYS_SCCR (SCCR_TBS | \ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ SCCR_DFALCD00 | SCCR_EBDF01) #endif /*----------------------------------------------------------------------- * *----------------------------------------------------------------------- * */ /*#define CONFIG_SYS_DER 0x2002000F*/ #define CONFIG_SYS_DER 0 /* * Init Memory Controller: * * BR0/1 and OR0/1 (FLASH) */ #define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ /* used to re-map FLASH both when starting from SRAM or FLASH: * restrict access enough to keep SRAM working (if any) * but not too much to meddle with FLASH accesses */ #define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ /* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ #define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX) #define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) /* * BR3 and OR3 (SDRAM) * */ #define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */ #define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ #define CONFIG_SYS_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS) #define CONFIG_SYS_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM) #define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_PS_32 | BR_V) /* * Memory Periodic Timer Prescaler */ /* periodic timer for refresh */ #define CONFIG_SYS_MAMR_PTA 208 /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ #define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ /* * MAMR settings for SDRAM */ /* 9 column SDRAM */ #define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ /* Ethernet at SCC2 */ #define CONFIG_SCC2_ENET /****************************************************************/ #define DSP_SIZE 0x00010000 /* 64K */ #define FPGA_SIZE 0x00010000 /* 64K */ #define DSP0_BASE 0xF1000000 #define DSP1_BASE (DSP0_BASE + DSP_SIZE) #define FPGA_BASE (DSP1_BASE + DSP_SIZE) #if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 #define ER_SIZE 0x00010000 /* 64K */ #define ER_BASE (FPGA_BASE + FPGA_SIZE) #define NAND_SIZE 0x00010000 /* 64K */ #define NAND_BASE (ER_BASE + ER_SIZE) #endif /****************************************************************/ #if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 #define STATUS_LED_BIT 0x00000001 /* bit 31 */ #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) #define STATUS_LED_STATE STATUS_LED_BLINKING #define STATUS_LED_BIT1 0x00000002 /* bit 30 */ #define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2) #define STATUS_LED_STATE1 STATUS_LED_OFF #define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ #define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ #endif /*****************************************************************************/ #ifndef __ASSEMBLY__ #if defined(CONFIG_NETVIA_VERSION) && CONFIG_NETVIA_VERSION >= 2 /* LEDs */ /* last value written to the external register; we cannot read back */ extern unsigned int last_er_val; /* led_id_t is unsigned long mask */ typedef unsigned int led_id_t; static inline void __led_init(led_id_t mask, int state) { unsigned int new_er_val; if (state) new_er_val = last_er_val & ~mask; else new_er_val = last_er_val | mask; *(volatile unsigned int *)ER_BASE = new_er_val; last_er_val = new_er_val; } static inline void __led_toggle(led_id_t mask) { unsigned int new_er_val; new_er_val = last_er_val ^ mask; *(volatile unsigned int *)ER_BASE = new_er_val; last_er_val = new_er_val; } static inline void __led_set(led_id_t mask, int state) { unsigned int new_er_val; if (state) new_er_val = last_er_val & ~mask; else new_er_val = last_er_val | mask; *(volatile unsigned int *)ER_BASE = new_er_val; last_er_val = new_er_val; } /* MAX3100 console */ #define MAX3100_SPI_RXD_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) #define MAX3100_SPI_RXD_BIT 0x00000008 #define MAX3100_SPI_TXD_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) #define MAX3100_SPI_TXD_BIT 0x00000004 #define MAX3100_SPI_CLK_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat) #define MAX3100_SPI_CLK_BIT 0x00000002 #define MAX3100_CS_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) #define MAX3100_CS_BIT 0x0010 #endif #endif /*************************************************************************************************/ #endif /* __CONFIG_H */