/* * Copyright 2006 Freescale Semiconductor. * * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ /* * MPC8641HPCN board configuration file * * Make sure you change the MAC address and other network params first, * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. */ #ifndef __CONFIG_H #define __CONFIG_H /* High Level Configuration Options */ #define CONFIG_MPC86xx 1 /* MPC86xx */ #define CONFIG_MPC8641 1 /* MPC8641 specific */ #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ #define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ #undef DEBUG #ifdef RUN_DIAG #define CFG_DIAG_ADDR 0xff800000 #endif #define CFG_RESET_ADDRESS 0xfff00100 /*#undef CONFIG_PCI*/ #define CONFIG_PCI #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ #undef CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ #define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef #define CONFIG_NUM_DDR_CONTROLLERS 2 /* #define CONFIG_DDR_INTERLEAVE 1 */ #define CACHE_LINE_INTERLEAVING 0x20000000 #define PAGE_INTERLEAVING 0x21000000 #define BANK_INTERLEAVING 0x22000000 #define SUPER_BANK_INTERLEAVING 0x23000000 #define CONFIG_ALTIVEC 1 /* * L2CR setup -- make sure this is right for your board! */ #define CFG_L2 #define L2_INIT 0 #define L2_ENABLE (L2CR_L2E) #ifndef CONFIG_SYS_CLK_FREQ #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) #endif #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest region */ #define CFG_MEMTEST_END 0x00400000 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ #define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ /* * DDR Setup */ #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE #define CONFIG_VERY_BIG_RAM #define MPC86xx_DDR_SDRAM_CLK_CNTL #if defined(CONFIG_SPD_EEPROM) /* * Determine DDR configuration from I2C interface. */ #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */ #define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */ #define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */ #define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */ #else /* * Manually set up DDR1 parameters */ #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */ #define CFG_DDR_CS0_BNDS 0x0000000F #define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ #define CFG_DDR_EXT_REFRESH 0x00000000 #define CFG_DDR_TIMING_0 0x00260802 #define CFG_DDR_TIMING_1 0x39357322 #define CFG_DDR_TIMING_2 0x14904cc8 #define CFG_DDR_MODE_1 0x00480432 #define CFG_DDR_MODE_2 0x00000000 #define CFG_DDR_INTERVAL 0x06090100 #define CFG_DDR_DATA_INIT 0xdeadbeef #define CFG_DDR_CLK_CTRL 0x03800000 #define CFG_DDR_OCD_CTRL 0x00000000 #define CFG_DDR_OCD_STATUS 0x00000000 #define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ #define CFG_DDR_CONTROL2 0x04400000 /* Not used in fixed_sdram function */ #define CFG_DDR_MODE 0x00000022 #define CFG_DDR_CS1_BNDS 0x00000000 #define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */ #define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */ #define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */ #define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */ #endif #define CFG_ID_EEPROM 1 #define ID_EEPROM_ADDR 0x57 /* * In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000. * There is an 8MB flash. In effect, the addresses from fe000000 to fe7fffff * map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff. * However, when u-boot comes up, the flash_init needs hard start addresses * to build its info table. For user convenience, the flash addresses is * fe800000 and ff800000. That way, u-boot knows where the flash is * and the user can download u-boot code from promjet to fef00000, a * more intuitive location than fe700000. * * Note that, on switching the boot location, fef00000 becomes fff00000. */ #define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */ #define CFG_FLASH_BASE2 0xff800000 #define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2} #define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */ #define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Boot Flash area*/ #define CFG_BR1_PRELIM 0xfe001001 /* port size 16bit */ #define CFG_OR1_PRELIM 0xff006ff7 /* 16MB Alternate Boot Flash area*/ #define CFG_BR2_PRELIM 0xf8201001 /* port size 16bit */ #define CFG_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/ #define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */ #define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ #define PIXIS_BASE 0xf8100000 /* PIXIS registers */ #define PIXIS_ID 0x0 /* Board ID at offset 0 */ #define PIXIS_VER 0x1 /* Board version at offset 1 */ #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ #define PIXIS_VCTL 0x10 /* VELA Control Register */ #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ #define CFG_MAX_FLASH_BANKS 2 /* number of banks */ #define CFG_MAX_FLASH_SECT 128 /* sectors per device */ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #define CFG_FLASH_CFI_DRIVER #define CFG_FLASH_CFI #define CFG_FLASH_EMPTY_INFO #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) #define CFG_RAMBOOT #else #undef CFG_RAMBOOT #endif #if defined(CFG_RAMBOOT) #undef CONFIG_SPD_EEPROM #define CFG_SDRAM_SIZE 256 #endif #undef CONFIG_CLOCKS_IN_MHZ #define CONFIG_L1_INIT_RAM #define CFG_INIT_RAM_LOCK 1 #ifndef CFG_INIT_RAM_LOCK #define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ #else #define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ #endif #define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_NS16550 #define CFG_NS16550_SERIAL #define CFG_NS16550_REG_SIZE 1 #define CFG_NS16550_CLK get_bus_freq(0) #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} #define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) #define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) /* Use the HUSH parser */ #define CFG_HUSH_PARSER #ifdef CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " #endif /* * Pass open firmware flat tree to kernel */ #define CONFIG_OF_FLAT_TREE 1 #define CONFIG_OF_BOARD_SETUP 1 /* maximum size of the flat tree (8K) */ #define OF_FLAT_TREE_MAX_SIZE 8192 #define OF_CPU "PowerPC,8641@0" #define OF_SOC "soc8641@f8000000" #define OF_TBCLK (bd->bi_busfreq / 4) #define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500" #define CFG_64BIT_VSPRINTF 1 #define CFG_64BIT_STRTOUL 1 /* * I2C */ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ #define CFG_I2C_OFFSET 0x3100 /* * RapidIO MMU */ #define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ #define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE #define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ /* * General PCI * Addresses are mapped 1-1. */ #define CFG_PCI1_MEM_BASE 0x80000000 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ #define CFG_PCI1_IO_BASE 0xe2000000 #define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE #define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ /* PCI view of System Memory */ #define CFG_PCI_MEMORY_BUS 0x00000000 #define CFG_PCI_MEMORY_PHYS 0x00000000 #define CFG_PCI_MEMORY_SIZE 0x80000000 /* For RTL8139 */ #define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);}) #define _IO_BASE 0x00000000 #define CFG_PCI2_MEM_BASE 0xa0000000 #define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE #define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */ #define CFG_PCI2_IO_BASE 0xe3000000 #define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE #define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */ #if defined(CONFIG_PCI) #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #undef CFG_SCSI_SCAN_BUS_REVERSE #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_RTL8139 #undef CONFIG_EEPRO100 #undef CONFIG_TULIP #if !defined(CONFIG_PCI_PNP) #define PCI_ENET0_IOADDR 0xe0000000 #define PCI_ENET0_MEMADDR 0xe0000000 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ #endif #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_DOS_PARTITION #define CONFIG_SCSI_AHCI #ifdef CONFIG_SCSI_AHCI #define CONFIG_SATA_ULI5288 #define CFG_SCSI_MAX_SCSI_ID 4 #define CFG_SCSI_MAX_LUN 1 #define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) #define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE #endif #endif /* CONFIG_PCI */ #if defined(CONFIG_TSEC_ENET) #ifndef CONFIG_NET_MULTI #define CONFIG_NET_MULTI 1 #endif #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_TSEC1 1 #define CONFIG_TSEC1_NAME "eTSEC1" #define CONFIG_TSEC2 1 #define CONFIG_TSEC2_NAME "eTSEC2" #define CONFIG_TSEC3 1 #define CONFIG_TSEC3_NAME "eTSEC3" #define CONFIG_TSEC4 1 #define CONFIG_TSEC4_NAME "eTSEC4" #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC3_PHY_ADDR 2 #define TSEC4_PHY_ADDR 3 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define TSEC3_PHYIDX 0 #define TSEC4_PHYIDX 0 #define CONFIG_ETHPRIME "eTSEC1" #endif /* CONFIG_TSEC_ENET */ /* * BAT0 2G Cacheable, non-guarded * 0x0000_0000 2G DDR */ #define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) #define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) #define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) #define CFG_IBAT0U CFG_DBAT0U /* * BAT1 1G Cache-inhibited, guarded * 0x8000_0000 512M PCI-Express 1 Memory * 0xa000_0000 512M PCI-Express 2 Memory * Changed it for operating from 0xd0000000 */ #define CFG_DBAT1L ( CFG_PCI1_MEM_BASE | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT1U CFG_DBAT1U /* * BAT2 512M Cache-inhibited, guarded * 0xc000_0000 512M RapidIO Memory */ #define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP) #define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT2U CFG_DBAT2U /* * BAT3 4M Cache-inhibited, guarded * 0xf800_0000 4M CCSR */ #define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) #define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT3U CFG_DBAT3U /* * BAT4 32M Cache-inhibited, guarded * 0xe200_0000 16M PCI-Express 1 I/O * 0xe300_0000 16M PCI-Express 2 I/0 * Note that this is at 0xe0000000 */ #define CFG_DBAT4L ( CFG_PCI1_IO_BASE | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP) #define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT4U CFG_DBAT4U /* * BAT5 128K Cacheable, non-guarded * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory) */ #define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) #define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) #define CFG_IBAT5L CFG_DBAT5L #define CFG_IBAT5U CFG_DBAT5U /* * BAT6 32M Cache-inhibited, guarded * 0xfe00_0000 32M FLASH */ #define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP) #define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE) #define CFG_IBAT6U CFG_DBAT6U #define CFG_DBAT7L 0x00000000 #define CFG_DBAT7U 0x00000000 #define CFG_IBAT7L 0x00000000 #define CFG_IBAT7U 0x00000000 /* * Environment */ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ #define CFG_ENV_SIZE 0x2000 #else #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) #define CFG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #if defined(CFG_RAMBOOT) #if defined(CONFIG_PCI) #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ | CFG_CMD_PING \ | CFG_CMD_PCI \ | CFG_CMD_I2C \ | CFG_CMD_SCSI \ | CFG_CMD_EXT2) \ & \ ~(CFG_CMD_ENV)) #else #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ | CFG_CMD_PING \ | CFG_CMD_I2C) \ & \ ~(CFG_CMD_ENV)) #endif #else #if defined(CONFIG_PCI) #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ | CFG_CMD_PCI \ | CFG_CMD_PING \ | CFG_CMD_I2C \ | CFG_CMD_SCSI \ | CFG_CMD_EXT2) #else #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ | CFG_CMD_PING \ | CFG_CMD_I2C) #endif #endif #include #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ /* Cache Configuration */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* * Environment Configuration */ /* The mac addresses for all ethernet interface */ #if defined(CONFIG_TSEC_ENET) #define CONFIG_ETHADDR 00:E0:0C:00:00:01 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD #define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD #endif #define CONFIG_HAS_ETH1 1 #define CONFIG_HAS_ETH2 1 #define CONFIG_HAS_ETH3 1 #define CONFIG_IPADDR 192.168.1.100 #define CONFIG_HOSTNAME unknown #define CONFIG_ROOTPATH /opt/nfsroot #define CONFIG_BOOTFILE uImage #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ #define CONFIG_SERVERIP 192.168.1.1 #define CONFIG_GATEWAYIP 192.168.1.1 #define CONFIG_NETMASK 255.255.255.0 /* default location for tftp and bootm */ #define CONFIG_LOADADDR 1000000 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_BAUDRATE 115200 #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ "tftpflash=tftpboot $loadaddr $uboot; " \ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ "erase " MK_STR(TEXT_BASE) " +$filesize; " \ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=your.ramdisk.u-boot\0" \ "dtbaddr=c00000\0" \ "dtbfile=mpc8641_hpcn.dtb\0" \ "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ "maxcpus=2" #define CONFIG_NFSBOOTCOMMAND \ "setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ "tftp $dtbaddr $dtbfile;" \ "bootm $loadaddr - $dtbaddr" #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ "tftp $dtbaddr $dtbfile;" \ "bootm $loadaddr $ramdiskaddr $dtbaddr" #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND #endif /* __CONFIG_H */