/*
 * Copyright 2004 Freescale Semiconductor.
 * (C) Copyright 2002,2003 Motorola,Inc.
 * Xianghua Xiao <X.Xiao@motorola.com>
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * mpc8540ads board configuration file
 *
 * Please refer to doc/README.mpc85xx for more info.
 *
 * Make sure you change the MAC address and other network params first,
 * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/* High Level Configuration Options */
#define CONFIG_BOOKE		1	/* BOOKE */
#define CONFIG_E500		1	/* BOOKE e500 family */
#define CONFIG_MPC85xx		1	/* MPC8540/MPC8560 */
#define CONFIG_MPC8540		1	/* MPC8540 specific */
#define CONFIG_MPC8540ADS	1	/* MPC8540ADS board specific */

#define CONFIG_PCI
#define CONFIG_TSEC_ENET 		/* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_ECC			/* only for ECC DDR module */
#define CONFIG_DDR_DLL			/* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */

/*
 * Use Localbus SDRAM to emulate flash before we can program the flash.
 * Normally you need a flash-boot image(u-boot.bin).
 * If unsure #undef this.
 */
#undef CONFIG_RAM_AS_FLASH

/*
 * sysclk for MPC85xx
 *
 * Two valid values are:
 *    33000000
 *    66000000
 *
 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
 * is likely the desired value here.  The board, however, can run and
 * defaults to 66Mhz.  In any event, this value must match the settings
 * of SW15[1] and SW17[8], and likely SW6[0:1], the SYSCLK as well.
 *
 *	SW17[8] ------+    SW6
 *	SW15[1] ----+ |   [0:1]
 *		    V V    V V
 *	33MHz	    1 1    1 0
 *	66MHz	    0 0    0 1
 */

#define CONFIG_SYS_CLK_FREQ	66000000


#if !defined(CONFIG_SPD_EEPROM)
#define CONFIG_DDR_SETTING	/* manually set up DDR parameters */
#endif

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE			/* toggle L2 cache */
#define CONFIG_BTB			/* toggle branch predition */
#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */

#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */

#undef	CFG_DRAM_TEST			/* memory test, takes time */
#define CFG_MEMTEST_START	0x00200000	/* memtest region */
#define CFG_MEMTEST_END		0x00400000


/*
 * Base addresses -- Note these are effective addresses where the
 * actual resources get mapped (not physical addresses)
 */
#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */

#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
#define CFG_SDRAM_SIZE		128             /* DDR is 128MB */

/*
 * SDRAM on the Local Bus
 */
#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_LBC_SDRAM_BASE	0xfc000000	/* Localbus SDRAM */
#else
#define CFG_LBC_SDRAM_BASE	0xf0000000	/* Localbus SDRAM */
#endif
#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */

#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_FLASH_BASE		0xf8000000	/* start of FLASH 16M */
#define CFG_BR0_PRELIM		0xf8001801	/* port size 32bit */
#else /* Boot from real Flash */
#define CFG_FLASH_BASE		0xff000000	/* start of FLASH 16M */
#define CFG_BR0_PRELIM		0xff001801	/* port size 32bit */
#endif

#define CFG_OR0_PRELIM		0xff006ff7	/* 16MB Flash */
#define CFG_MAX_FLASH_BANKS	1		/* number of banks */
#define CFG_MAX_FLASH_SECT	64		/* sectors per device */
#undef	CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */


#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
#undef  CFG_RAMBOOT
#endif

#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */

#undef CONFIG_CLOCKS_IN_MHZ

#if defined(CONFIG_DDR_SETTING)
#define CFG_DDR_CS0_BNDS	0x00000007	/* 0-128MB */
#define CFG_DDR_CS0_CONFIG	0x80000002
#define CFG_DDR_TIMING_1	0x37344321
#define CFG_DDR_TIMING_2	0x00000800  /* P9-45,may need tuning */
#define CFG_DDR_CONTROL		0xc2000000  /* unbuffered,no DYN_PWR */
#define CFG_DDR_MODE		0x00000062  /* DLL,normal,seq,4/2.5 */
#define CFG_DDR_INTERVAL	0x05200100  /* autocharge,no open page */
#endif


/*
 * Local Bus Definitions
 */

/*
 * Base Register 2 and Option Register 2 configure SDRAM.
 * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
 *
 * For BR2, need:
 *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
 *    port-size = 32-bits = BR2[19:20] = 11
 *    no parity checking = BR2[21:22] = 00
 *    SDRAM for MSEL = BR2[24:26] = 011
 *    Valid = BR[31] = 1
 *
 * 0    4    8    12   16   20   24   28
 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
 *
 * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
 * FIXME: the top 17 bits of BR2.
 */

#define CFG_BR2_PRELIM		0xf0001861

/*
 * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
 *
 * For OR2, need:
 *    64MB mask for AM, OR2[0:7] = 1111 1100
 *		   XAM, OR2[17:18] = 11
 *    9 columns OR2[19-21] = 010
 *    13 rows   OR2[23-25] = 100
 *    EAD set for extra time OR[31] = 1
 *
 * 0    4    8    12   16   20   24   28
 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
 */

#define CFG_OR2_PRELIM		0xfc006901

#define CFG_LBC_LCRR		0x00030004    /* LB clock ratio reg */
#define CFG_LBC_LBCR		0x00000000    /* LB config reg */
#define CFG_LBC_LSRT		0x20000000    /* LB sdram refresh timer */
#define CFG_LBC_MRTPR		0x20000000    /* LB refresh timer prescal*/

/*
 * LSDMR masks
 */
#define CFG_LBC_LSDMR_RFEN	(1 << (31 -  1))
#define CFG_LBC_LSDMR_BSMA1516	(3 << (31 - 10))
#define CFG_LBC_LSDMR_BSMA1617	(4 << (31 - 10))
#define CFG_LBC_LSDMR_RFCR5	(3 << (31 - 16))
#define CFG_LBC_LSDMR_RFCR16	(7 << (31 - 16))
#define CFG_LBC_LSDMR_PRETOACT3	(3 << (31 - 19))
#define CFG_LBC_LSDMR_PRETOACT7	(7 << (31 - 19))
#define CFG_LBC_LSDMR_ACTTORW3	(3 << (31 - 22))
#define CFG_LBC_LSDMR_ACTTORW7	(7 << (31 - 22))
#define CFG_LBC_LSDMR_ACTTORW6	(6 << (31 - 22))
#define CFG_LBC_LSDMR_BL8	(1 << (31 - 23))
#define CFG_LBC_LSDMR_WRC2	(2 << (31 - 27))
#define CFG_LBC_LSDMR_WRC4	(0 << (31 - 27))
#define CFG_LBC_LSDMR_BUFCMD	(1 << (31 - 29))
#define CFG_LBC_LSDMR_CL3	(3 << (31 - 31))

#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))

#define CFG_LBC_LSDMR_COMMON	( CFG_LBC_LSDMR_BSMA1516	\
				| CFG_LBC_LSDMR_RFCR5		\
				| CFG_LBC_LSDMR_PRETOACT3	\
				| CFG_LBC_LSDMR_ACTTORW3	\
				| CFG_LBC_LSDMR_BL8		\
				| CFG_LBC_LSDMR_WRC2		\
				| CFG_LBC_LSDMR_CL3		\
				| CFG_LBC_LSDMR_RFEN		\
				)

/*
 * SDRAM Controller configuration sequence.
 */
#define CFG_LBC_LSDMR_1		( CFG_LBC_LSDMR_COMMON \
				| CFG_LBC_LSDMR_OP_PCHALL)  /*0x2861b723*/
#define CFG_LBC_LSDMR_2		( CFG_LBC_LSDMR_COMMON \
				| CFG_LBC_LSDMR_OP_ARFRSH)  /*0x0861b723*/
#define CFG_LBC_LSDMR_3		( CFG_LBC_LSDMR_COMMON \
				| CFG_LBC_LSDMR_OP_ARFRSH)  /*0x0861b723*/
#define CFG_LBC_LSDMR_4		( CFG_LBC_LSDMR_COMMON \
				| CFG_LBC_LSDMR_OP_MRW)     /*0x1861b723*/
#define CFG_LBC_LSDMR_5		( CFG_LBC_LSDMR_COMMON \
				| CFG_LBC_LSDMR_OP_NORMAL)  /*0x4061b723*/


#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_BR4_PRELIM          0xf8000801      /* 32KB, 8-bit wide for ADS config reg */
#else
#define CFG_BR4_PRELIM          0xf8000801      /* 32KB, 8-bit wide for ADS config reg */
#endif
#define CFG_OR4_PRELIM		0xffffe1f1
#define CFG_BCSR		(CFG_BR4_PRELIM & 0xffff8000)

#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 	1
#define CFG_INIT_RAM_ADDR	0x40000000	/* Initial RAM address */
#define CFG_INIT_RAM_END    	0x4000	    	/* End of used area in RAM */

#define CFG_GBL_DATA_SIZE  	128		/* num bytes initial data */
#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

#define CFG_MONITOR_LEN	    	(256 * 1024)    /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN	    	(128 * 1024)    /* Reserved for malloc */

/* Serial Port */
#define CONFIG_CONS_INDEX     1
#undef	CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE    1
#define CFG_NS16550_CLK		get_bus_freq(0)

#define CFG_BAUDRATE_TABLE  \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

#define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)

/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef  CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif

/* I2C */
#define  CONFIG_HARD_I2C		/* I2C with hardware support*/
#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
#define CFG_I2C_SLAVE		0x7F
#define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */

/* RapidIO MMU */
#define CFG_RIO_MEM_BASE	0xc0000000	/* base address */
#define CFG_RIO_MEM_PHYS	CFG_RIO_MEM_BASE
#define CFG_RIO_MEM_SIZE	0x20000000	/* 128M */

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CFG_PCI1_MEM_BASE	0x80000000
#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
#define CFG_PCI1_IO_BASE	0xe2000000
#define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE
#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M */

#if defined(CONFIG_PCI)

#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP		       	/* do pci plug-and-play */

#undef CONFIG_EEPRO100
#undef CONFIG_TULIP

#if !defined(CONFIG_PCI_PNP)
    #define PCI_ENET0_IOADDR	0xe0000000
    #define PCI_ENET0_MEMADDR	0xe0000000
    #define PCI_IDSEL_NUMBER	0x0c 	/* slot0->3(IDSEL)=12->15 */
#endif

#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */

#endif	/* CONFIG_PCI */


#if defined(CONFIG_TSEC_ENET)

#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 	1
#endif

#define CONFIG_MII		1	/* MII PHY management */
#define CONFIG_MPC85XX_TSEC1	1
#define CONFIG_MPC85XX_TSEC2	1
#define CONFIG_MPC85XX_FEC	1
#define TSEC1_PHY_ADDR		0
#define TSEC2_PHY_ADDR		1
#define FEC_PHY_ADDR		3
#define TSEC1_PHYIDX		0
#define TSEC2_PHYIDX		0
#define FEC_PHYIDX		0
#define CONFIG_ETHPRIME		"MOTO ENET0"

#endif	/* CONFIG_TSEC_ENET */


/*
 * Environment
 */
#ifndef CFG_RAMBOOT
  #if defined(CONFIG_RAM_AS_FLASH)
  #define CFG_ENV_IS_NOWHERE
  #define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0x100000)
  #define CFG_ENV_SIZE		0x2000
  #else
  #define CFG_ENV_IS_IN_FLASH	1
  #define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
  #define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
  #endif
  #define CFG_ENV_SIZE		0x2000
#else
#define CFG_NO_FLASH		1	/* Flash is not usable now */
#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
#define CFG_ENV_SIZE		0x2000
#endif

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
  #if defined(CONFIG_PCI)
    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
				 | CFG_CMD_PING		\
				 | CFG_CMD_PCI		\
				 | CFG_CMD_I2C)		\
				&			\
				 ~(CFG_CMD_ENV		\
				  | CFG_CMD_LOADS))
  #else
    #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL	\
				 | CFG_CMD_PING		\
				 | CFG_CMD_I2C)		\
				&			\
				 ~(CFG_CMD_ENV		\
				  | CFG_CMD_LOADS))
  #endif
#else
  #if defined(CONFIG_PCI)
    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
				| CFG_CMD_PCI		\
				| CFG_CMD_PING		\
				| CFG_CMD_I2C)
  #else
    #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL		\
				| CFG_CMD_PING		\
				| CFG_CMD_I2C)
  #endif
#endif

#include <cmd_confdefs.h>

#undef CONFIG_WATCHDOG			/* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CFG_LONGHELP			/* undef to save memory	*/
#define CFG_LOAD_ADDR	0x2000000	/* default load address */
#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */

#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
    #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
#else
    #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
#endif

#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS	16		/* max number of command args */
#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/

/* Cache Configuration */
#define CFG_DCACHE_SIZE		32768
#define CFG_CACHELINE_SIZE	32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
#endif

/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM	0x02		/* Software reboot */

#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
#endif

/*****************************/
/* Environment Configuration */
/*****************************/

/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_ETHADDR   00:E0:0C:00:00:FD
#define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
#define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
#endif

#define CONFIG_IPADDR    192.168.1.253

#define CONFIG_HOSTNAME		unknown
#define CONFIG_ROOTPATH		/nfsroot
#define CONFIG_BOOTFILE		your.uImage

#define CONFIG_SERVERIP  192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK   255.255.255.0

#define CONFIG_LOADADDR  200000	/* default location for tftp and bootm */

#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */

#define CONFIG_BAUDRATE	115200

#define	CONFIG_EXTRA_ENV_SETTINGS					\
   "netdev=eth0\0"                                                      \
   "consoledev=ttyS0\0"                                                 \
   "ramdiskaddr=400000\0"						\
   "ramdiskfile=your.ramdisk.u-boot\0"

#define CONFIG_NFSBOOTCOMMAND						\
   "setenv bootargs root=/dev/nfs rw "                                  \
      "nfsroot=$serverip:$rootpath "                                    \
      "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
      "console=$consoledev,$baudrate $othbootargs;"                     \
   "tftp $loadaddr $bootfile;"                                          \
   "bootm $loadaddr"

#define CONFIG_RAMBOOTCOMMAND \
   "setenv bootargs root=/dev/ram rw "                                  \
      "console=$consoledev,$baudrate $othbootargs;"                     \
   "tftp $ramdiskaddr $ramdiskfile;"                                    \
   "tftp $loadaddr $bootfile;"                                          \
   "bootm $loadaddr $ramdiskaddr"

#define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND

#endif	/* __CONFIG_H */