/* * Copyright (C) 2006 Freescale Semiconductor, Inc. * * Dave Liu <daveliu@freescale.com> * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #ifndef __CONFIG_H #define __CONFIG_H #undef DEBUG /* * High Level Configuration Options */ #define CONFIG_E300 1 /* E300 family */ #define CONFIG_QE 1 /* Has QE */ #define CONFIG_MPC83XX 1 /* MPC83XX family */ #define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ #define CONFIG_MPC8360EMDS 1 /* MPC8360EMDS board specific */ /* * System Clock Setup */ #ifdef CONFIG_PCISLAVE #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ #else #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ #endif #ifndef CONFIG_SYS_CLK_FREQ #define CONFIG_SYS_CLK_FREQ 66000000 #endif /* * Hardware Reset Configuration Word */ #define CFG_HRCW_LOW (\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ HRCWL_DDR_TO_SCB_CLK_1X1 |\ HRCWL_CSB_TO_CLKIN_4X1 |\ HRCWL_VCO_1X2 |\ HRCWL_CE_PLL_VCO_DIV_4 |\ HRCWL_CE_PLL_DIV_1X1 |\ HRCWL_CE_TO_PLL_1X6 |\ HRCWL_CORE_TO_CSB_2X1) #ifdef CONFIG_PCISLAVE #define CFG_HRCW_HIGH (\ HRCWH_PCI_AGENT |\ HRCWH_PCI1_ARBITER_DISABLE |\ HRCWH_PCICKDRV_DISABLE |\ HRCWH_CORE_ENABLE |\ HRCWH_FROM_0XFFF00100 |\ HRCWH_BOOTSEQ_DISABLE |\ HRCWH_SW_WATCHDOG_DISABLE |\ HRCWH_ROM_LOC_LOCAL_16BIT) #else #define CFG_HRCW_HIGH (\ HRCWH_PCI_HOST |\ HRCWH_PCI1_ARBITER_ENABLE |\ HRCWH_PCICKDRV_ENABLE |\ HRCWH_CORE_ENABLE |\ HRCWH_FROM_0X00000100 |\ HRCWH_BOOTSEQ_DISABLE |\ HRCWH_SW_WATCHDOG_DISABLE |\ HRCWH_ROM_LOC_LOCAL_16BIT) #endif /* * System IO Config */ #define CFG_SICRH 0x00000000 #define CFG_SICRL 0x40000000 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ /* * IMMR new address */ #define CFG_IMMR 0xE0000000 /* * DDR Setup */ #define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ #define CFG_SDRAM_BASE CFG_DDR_BASE #define CFG_DDR_SDRAM_BASE CFG_DDR_BASE #define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) #define CFG_83XX_DDR_USES_CS0 #define CONFIG_DDR_ECC /* support DDR ECC function */ #define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ /* * DDRCDR - DDR Control Driver Register */ #define CFG_DDRCDR_VALUE 0x80080001 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ #if defined(CONFIG_SPD_EEPROM) /* * Determine DDR configuration from I2C interface. */ #define SPD_EEPROM_ADDRESS 0x52 /* DDR SODIMM */ #else /* * Manually set up DDR parameters */ #define CFG_DDR_SIZE 256 /* MB */ #if defined(CONFIG_DDR_II) #define CFG_DDRCDR 0x80080001 #define CFG_DDR_CS0_BNDS 0x0000000f #define CFG_DDR_CS0_CONFIG 0x80330102 #define CFG_DDR_TIMING_0 0x00220802 #define CFG_DDR_TIMING_1 0x38357322 #define CFG_DDR_TIMING_2 0x2f9048c8 #define CFG_DDR_TIMING_3 0x00000000 #define CFG_DDR_CLK_CNTL 0x02000000 #define CFG_DDR_MODE 0x47d00432 #define CFG_DDR_MODE2 0x8000c000 #define CFG_DDR_INTERVAL 0x03cf0080 #define CFG_DDR_SDRAM_CFG 0x43000000 #define CFG_DDR_SDRAM_CFG2 0x00401000 #else #define CFG_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9) #define CFG_DDR_TIMING_1 0x37344321 /* tCL-tRCD-tRP-tRAS=2.5-3-3-7 */ #define CFG_DDR_TIMING_2 0x00000800 /* may need tuning */ #define CFG_DDR_CONTROL 0x42008000 /* Self refresh,2T timing */ #define CFG_DDR_MODE 0x20000162 /* DLL,normal,seq,4/2.5 */ #define CFG_DDR_INTERVAL 0x045b0100 /* page mode */ #endif #endif /* * Memory test */ #undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00000000 /* memtest region */ #define CFG_MEMTEST_END 0x00100000 /* * The reserved memory */ #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) #define CFG_RAMBOOT #else #undef CFG_RAMBOOT #endif #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* * Initial RAM Base Address Setup */ #define CFG_INIT_RAM_LOCK 1 #define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ #define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ #define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) /* * Local Bus Configuration & Clock Setup */ #define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4) #define CFG_LBC_LBCR 0x00000000 /* * FLASH on the Local Bus */ #define CFG_FLASH_CFI /* use the Common Flash Interface */ #define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ #define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ #define CFG_FLASH_SIZE 32 /* max FLASH size is 32M */ #define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ #define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ #define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ BR_V) /* valid */ #define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ #define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ #undef CFG_FLASH_CHECKSUM /* * BCSR on the Local Bus */ #define CFG_BCSR 0xF8000000 #define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */ #define CFG_LBLAWAR1_PRELIM 0x8000000F /* Access window size 64K */ #define CFG_BR1_PRELIM (CFG_BCSR|0x00000801) /* Port size=8bit, MSEL=GPCM */ #define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ /* * SDRAM on the Local Bus */ #define CFG_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */ #define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ #define CFG_LB_SDRAM /* if board has SRDAM on local bus */ #ifdef CFG_LB_SDRAM #define CFG_LBLAWBAR2_PRELIM CFG_LBC_SDRAM_BASE #define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64MB */ /*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */ /* * Base Register 2 and Option Register 2 configure SDRAM. * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000. * * For BR2, need: * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 * port size = 32-bits = BR2[19:20] = 11 * no parity checking = BR2[21:22] = 00 * SDRAM for MSEL = BR2[24:26] = 011 * Valid = BR[31] = 1 * * 0 4 8 12 16 20 24 28 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 * * CFG_LBC_SDRAM_BASE should be masked and OR'ed into * the top 17 bits of BR2. */ #define CFG_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */ /* * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64. * * For OR2, need: * 64MB mask for AM, OR2[0:7] = 1111 1100 * XAM, OR2[17:18] = 11 * 9 columns OR2[19-21] = 010 * 13 rows OR2[23-25] = 100 * EAD set for extra time OR[31] = 1 * * 0 4 8 12 16 20 24 28 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 */ #define CFG_OR2_PRELIM 0xfc006901 #define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ #define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ /* * LSDMR masks */ #define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) #define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) #define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) #define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) #define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) #define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) #define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) #define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) #define CFG_LBC_LSDMR_COMMON 0x0063b723 /* * SDRAM Controller configuration sequence. */ #define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_PCHALL) #define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_ARFRSH) #define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_ARFRSH) #define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_MRW) #define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \ | CFG_LBC_LSDMR_OP_NORMAL) #endif /* * Windows to access PIB via local bus */ #define CFG_LBLAWBAR3_PRELIM 0xf8010000 /* windows base 0xf8010000 */ #define CFG_LBLAWAR3_PRELIM 0x8000000e /* windows size 32KB */ /* * CS4 on Local Bus, to PIB */ #define CFG_BR4_PRELIM 0xf8008801 /* CS4 base address at 0xf8008000 */ #define CFG_OR4_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ /* * CS5 on Local Bus, to PIB */ #define CFG_BR5_PRELIM 0xf8010801 /* CS5 base address at 0xf8010000 */ #define CFG_OR5_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ /* * Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_NS16550 #define CFG_NS16550_SERIAL #define CFG_NS16550_REG_SIZE 1 #define CFG_NS16550_CLK get_bus_freq(0) #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} #define CFG_NS16550_COM1 (CFG_IMMR+0x4500) #define CFG_NS16550_COM2 (CFG_IMMR+0x4600) #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ /* Use the HUSH parser */ #define CFG_HUSH_PARSER #ifdef CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " #endif /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #undef CONFIG_OF_FLAT_TREE #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_HAS_BD_T 1 #define CONFIG_OF_HAS_UBOOT_ENV 1 /* maximum size of the flat tree (8K) */ #define OF_FLAT_TREE_MAX_SIZE 8192 #define OF_CPU "PowerPC,8360@0" #define OF_SOC "soc8360@e0000000" #define OF_QE "qe@e0100000" #define OF_TBCLK (bd->bi_busfreq / 4) #define OF_STDOUT_PATH "/soc8360@e0000000/serial@4500" /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_FSL_I2C #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES {0x52} /* Don't probe these addrs */ #define CFG_I2C_OFFSET 0x3000 #define CFG_I2C2_OFFSET 0x3100 /* * Config on-board RTC */ #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ #define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ /* * General PCI * Addresses are mapped 1-1. */ #define CFG_PCI_MEM_BASE 0x80000000 #define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE #define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ #define CFG_PCI_MMIO_BASE 0x90000000 #define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE #define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ #define CFG_PCI_IO_BASE 0xE0300000 #define CFG_PCI_IO_PHYS 0xE0300000 #define CFG_PCI_IO_SIZE 0x100000 /* 1M */ #define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE #define CFG_PCI_SLV_MEM_BUS 0x00000000 #define CFG_PCI_SLV_MEM_SIZE 0x80000000 #ifdef CONFIG_PCI #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ #undef CONFIG_EEPRO100 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ #endif /* CONFIG_PCI */ #ifndef CONFIG_NET_MULTI #define CONFIG_NET_MULTI 1 #endif /* * QE UEC ethernet configuration */ #define CONFIG_UEC_ETH #define CONFIG_ETHPRIME "Freescale GETH" #define CONFIG_PHY_MODE_NEED_CHANGE #define CONFIG_UEC_ETH1 /* GETH1 */ #ifdef CONFIG_UEC_ETH1 #define CFG_UEC1_UCC_NUM 0 /* UCC1 */ #define CFG_UEC1_RX_CLK QE_CLK_NONE #define CFG_UEC1_TX_CLK QE_CLK9 #define CFG_UEC1_ETH_TYPE GIGA_ETH #define CFG_UEC1_PHY_ADDR 0 #define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII #endif #define CONFIG_UEC_ETH2 /* GETH2 */ #ifdef CONFIG_UEC_ETH2 #define CFG_UEC2_UCC_NUM 1 /* UCC2 */ #define CFG_UEC2_RX_CLK QE_CLK_NONE #define CFG_UEC2_TX_CLK QE_CLK4 #define CFG_UEC2_ETH_TYPE GIGA_ETH #define CFG_UEC2_PHY_ADDR 1 #define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII #endif /* * Environment */ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ #define CFG_ENV_SIZE 0x2000 #else #define CFG_NO_FLASH 1 /* Flash is not usable now */ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) #define CFG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #if defined(CFG_RAMBOOT) #if defined(CONFIG_PCI) #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ | CFG_CMD_PING \ | CFG_CMD_ASKENV \ | CFG_CMD_PCI \ | CFG_CMD_I2C) \ & \ ~(CFG_CMD_ENV \ | CFG_CMD_LOADS)) #else #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ | CFG_CMD_PING \ | CFG_CMD_ASKENV \ | CFG_CMD_I2C) \ & \ ~(CFG_CMD_ENV \ | CFG_CMD_LOADS)) #endif #else #if defined(CONFIG_PCI) #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ | CFG_CMD_PCI \ | CFG_CMD_PING \ | CFG_CMD_ASKENV \ | CFG_CMD_I2C) #else #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ | CFG_CMD_PING \ | CFG_CMD_ASKENV \ | CFG_CMD_I2C ) #endif #endif #include <cmd_confdefs.h> #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_LOAD_ADDR 0x2000000 /* default load address */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup */ #define CFG_HID0_INIT 0x000000000 #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK #define CFG_HID2 HID2_HBE /* * Cache Config */ #define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ #endif /* * MMU Setup */ /* DDR: cache cacheable */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CFG_DBAT0L CFG_IBAT0L #define CFG_DBAT0U CFG_IBAT0U /* IMMRBAR & PCI IO: cache-inhibit and guarded */ #define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) #define CFG_DBAT1L CFG_IBAT1L #define CFG_DBAT1U CFG_IBAT1U /* BCSR: cache-inhibit and guarded */ #define CFG_IBAT2L (CFG_BCSR | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_IBAT2U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) #define CFG_DBAT2L CFG_IBAT2L #define CFG_DBAT2U CFG_IBAT2U /* FLASH: icache cacheable, but dcache-inhibit and guarded */ #define CFG_IBAT3L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT3U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) #define CFG_DBAT3L (CFG_FLASH_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_DBAT3U CFG_IBAT3U /* Local bus SDRAM: cacheable */ #define CFG_IBAT4L (CFG_LBC_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT4U (CFG_LBC_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP) #define CFG_DBAT4L CFG_IBAT4L #define CFG_DBAT4U CFG_IBAT4U /* Stack in dcache: cacheable, no memory coherence */ #define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) #define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) #define CFG_DBAT5L CFG_IBAT5L #define CFG_DBAT5U CFG_IBAT5U #ifdef CONFIG_PCI /* PCI MEM space: cacheable */ #define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) #define CFG_DBAT6L CFG_IBAT6L #define CFG_DBAT6U CFG_IBAT6U /* PCI MMIO space: cache-inhibit and guarded */ #define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) #define CFG_DBAT7L CFG_IBAT7L #define CFG_DBAT7U CFG_IBAT7U #else #define CFG_IBAT6L (0) #define CFG_IBAT6U (0) #define CFG_IBAT7L (0) #define CFG_IBAT7U (0) #define CFG_DBAT6L CFG_IBAT6L #define CFG_DBAT6U CFG_IBAT6U #define CFG_DBAT7L CFG_IBAT7L #define CFG_DBAT7U CFG_IBAT7U #endif /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* * Environment Configuration */ #define CONFIG_ENV_OVERWRITE #if defined(CONFIG_UEC_ETH) #define CONFIG_ETHADDR 00:04:9f:ef:01:01 #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:04:9f:ef:01:02 #endif #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "consoledev=ttyS0\0" \ "ramdiskaddr=1000000\0" \ "ramdiskfile=ramfs.83xx\0" \ "fdtaddr=400000\0" \ "fdtfile=mpc8360emds.dtb\0" \ "" #define CONFIG_NFSBOOTCOMMAND \ "setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND #endif /* __CONFIG_H */