/* * (C) Copyright 2004 Sandburst Corporation * * SPDX-License-Identifier: GPL-2.0+ */ /************************************************************************ * METROBOX.h - configuration Sandburst MetroBox ***********************************************************************/ /* * $Id: METROBOX.h,v 1.21 2005/06/03 15:05:25 tsawyer Exp $ * * * $Log: METROBOX.h,v $ * Revision 1.21 2005/06/03 15:05:25 tsawyer * MB rev 2.0.3 KA rev 0.0.7. Add CONFIG_VERSION_VARIABLE, Add fakeled to MB * * Revision 1.20 2005/04/11 20:51:11 tsawyer * fix ethernet * * Revision 1.19 2005/04/06 15:13:36 tsawyer * Update appropriate files to coincide with u-boot 1.1.3 * * Revision 1.18 2005/03/10 14:16:02 tsawyer * add def'n for cis8201 short etch option. * * Revision 1.17 2005/03/09 19:49:51 tsawyer * Remove KGDB to allow use of 2nd serial port * * Revision 1.16 2004/12/02 19:00:23 tsawyer * Add misc_init_f to turn on i2c-1 and all four fans before sdram init * * Revision 1.15 2004/09/15 18:04:12 tsawyer * add multiple serial port support * * Revision 1.14 2004/09/03 15:27:51 tsawyer * All metrobox boards are at 66.66 sys clock * * Revision 1.13 2004/08/05 20:27:46 tsawyer * Remove system ace definitions, add net console support * * Revision 1.12 2004/07/29 20:00:13 tsawyer * Add i2c bus 1 * * Revision 1.11 2004/07/21 13:44:18 tsawyer * SystemACE is out, CF direct to local bus is in * * Revision 1.10 2004/06/29 19:08:55 tsawyer * Add CONFIG_MISC_INIT_R * * Revision 1.9 2004/06/28 21:30:53 tsawyer * Fix default BOOTARGS * * Revision 1.8 2004/06/17 15:51:08 tsawyer * auto complete * * Revision 1.7 2004/06/17 15:08:49 tsawyer * Add autocomplete * * Revision 1.6 2004/06/15 12:33:57 tsawyer * debugging checkpoint * * Revision 1.5 2004/06/12 19:48:28 tsawyer * Debugging checkpoint * * Revision 1.4 2004/06/02 13:03:06 tsawyer * Fix eth addrs * * Revision 1.3 2004/05/18 19:56:10 tsawyer * Change default bootcommand to pImage.metrobox * * Revision 1.2 2004/05/18 14:13:44 tsawyer * Add bringup values for bootargs and bootcommand. * Remove definition of ipaddress and serverip addresses. * * Revision 1.1 2004/04/16 15:08:54 tsawyer * Initial Revision * * */ #ifndef __CONFIG_H #define __CONFIG_H /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ #define CONFIG_METROBOX 1 /* Board is Metrobox */ #define CONFIG_440GX 1 /* Specifc GX support */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_F 1 /* Call board misc_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call board misc_init_r */ #define CONFIG_SYS_TEXT_BASE 0xFFF80000 #undef CONFIG_SYS_DRAM_TEST /* Disable-takes long time!*/ #define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ #define CONFIG_VERY_BIG_RAM 1 #define CONFIG_VERSION_VARIABLE #define CONFIG_IDENT_STRING " Sandburst Metrobox" /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */ #define CONFIG_SYS_MONITOR_BASE 0xfff80000 /* start of monitor */ #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) #define CONFIG_SYS_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08200000) #define CONFIG_SYS_BME32_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08500000) #define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700) /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ #define CONFIG_SYS_TEMP_STACK_OCM 1 #define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Rsrv 256kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Rsrv 128kB for malloc */ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_BAUDRATE 9600 #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * NVRAM/RTC * * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located. * The DS1743 code assumes this condition (i.e. -- it assumes the base * address for the RTC registers is: * * CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE * *----------------------------------------------------------------------*/ #define CONFIG_SYS_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs*/ #define CONFIG_RTC_DS174x 1 /* DS1743 RTC */ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #define CONFIG_SYS_MAX_FLASH_SECT 8 /* sectors per device */ #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase TO (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO(in ms) */ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup*/ #define SPD_EEPROM_ADDRESS {0x53} /* SPD i2c spd addresses */ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_PPC4XX #define CONFIG_SYS_I2C_PPC4XX_CH0 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_PPC4XX_CH1 #define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000 /* I2C speed 400kHz */ #define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F #define CONFIG_SYS_I2C_NOPROBES { { 0, 0x69} } /* Don't probe these addrs */ /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ #define CONFIG_ENV_IS_IN_NVRAM 1 /* Environment uses NVRAM */ #undef CONFIG_ENV_IS_IN_FLASH /* ... not in flash */ #undef CONFIG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ #define CONFIG_ENV_OVERWRITE 1 /* allow env overwrite */ #define CONFIG_ENV_SIZE 0x1000 /* Size of Env vars */ #define CONFIG_ENV_ADDR (CONFIG_SYS_NVRAM_BASE_ADDR) #define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/nfs rw nfsroot=$serverip:/home/metrobox0 nfsaddrs=$ipaddr:::::eth0:none " #define CONFIG_BOOTCOMMAND "tftp 8000000 pImage.metrobox;bootm 8000000" #define CONFIG_BOOTDELAY 5 /* disable autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial dnld */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /*----------------------------------------------------------------------- * Networking *----------------------------------------------------------------------*/ #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */ #define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */ #define CONFIG_PHY2_ADDR 0x08 /* PHY addr, MGMT, EMAC2 */ #define CONFIG_PHY3_ADDR 0x18 /* PHY addr, LCL, EMAC3 */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 #define CONFIG_HAS_ETH3 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_CIS8201_PHY 1 /* RGMII mode for Cicada */ #define CONFIG_CIS8201_SHORT_ETCH 1 /* Use short etch mode */ #define CONFIG_PHY_GIGE 1 /* GbE speed/duplex detect */ #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_NETMASK 255.255.0.0 #define CONFIG_ETHADDR 00:00:00:00:00:00 /* No EMAC 0 support */ #define CONFIG_ETH1ADDR 00:00:00:00:00:00 /* No EMAC 1 support */ #define CONFIG_SYS_RX_ETH_BUFFER 32 /* #eth rx buff & descrs */ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include <config_cmd_default.h> #define CONFIG_CMD_PCI #define CONFIG_CMD_IRQ #define CONFIG_CMD_I2C #define CONFIG_CMD_DHCP #define CONFIG_CMD_DATE #define CONFIG_CMD_BEDBUG #define CONFIG_CMD_PING #define CONFIG_CMD_DIAG #define CONFIG_CMD_MII #define CONFIG_CMD_NET #define CONFIG_CMD_ELF #define CONFIG_CMD_IDE #define CONFIG_CMD_FAT /* Include NetConsole support */ #define CONFIG_NETCONSOLE /* Include auto complete with tabs */ #define CONFIG_AUTO_COMPLETE 1 #define CONFIG_AUTO_COMPLETE 1 #define CONFIG_SYS_ALT_MEMTEST 1 /* use real memory test */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "MetroBox=> " /* Monitor Command Prompt */ #define CONFIG_SYS_HUSH_PARSER 1 /* HUSH for ext'd cli */ /*----------------------------------------------------------------------- * Console Buffer *----------------------------------------------------------------------*/ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */ /*----------------------------------------------------------------------- * Memory Test *----------------------------------------------------------------------*/ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ /*----------------------------------------------------------------------- * Compact Flash (in true IDE mode) *----------------------------------------------------------------------*/ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ #define CONFIG_IDE_RESET /* reset for ide supported */ #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ #define CONFIG_SYS_ATA_BASE_ADDR 0xF0000000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses*/ #define CONFIG_SYS_ATA_ALT_OFFSET 0x100000 /* Offset for alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 /* Directly connected CF, needs a stride to get to the correct offset */ #define CONFIG_DOS_PARTITION 1 /* Include dos partition */ /*----------------------------------------------------------------------- * PCI *----------------------------------------------------------------------*/ /* General PCI */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices */ #define CONFIG_SYS_PCI_TARGBASE (CONFIG_SYS_PCI_MEMBASE) /* Board-specific PCI */ #define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target*/ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x17BA /* Sandburst */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* kgdb serial port baud */ #endif /*----------------------------------------------------------------------- * Miscellaneous configurable options *----------------------------------------------------------------------*/ #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_SYS_LOAD_ADDR 0x8000000 /* default load address */ #define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info */ #endif /* __CONFIG_H */