/* * A collection of structures, addresses, and values associated with * the Motorola 860T MBX board. * Copied from the FADS stuff, which was originally copied from the MBX stuff! * Magnus Damm added defines for 8xxrom and extended bd_info. * Helmut Buchsbaum added bitvalues for BCSRx * Rob Taylor coverted it back to MBX * * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) */ /* ------------------------------------------------------------------------- */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #include <mpc8xx_irq.h> #define CONFIG_MPC860 1 #define CONFIG_MPC860T 1 #define CONFIG_MBX 1 #define CONFIG_8xx_CPUCLOCK 40 #define CONFIG_8xx_BUSCLOCK (CONFIG_8xx_CPUCLOCK) #define TARGET_SYSTEM_FREQUENCY 40 #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ #undef CONFIG_8xx_CONS_SMC2 #define CONFIG_BAUDRATE 9600 #define MPC8XX_FACT 10 /* Multiply by 10 */ #define MPC8XX_XIN 40000000 /* 50 MHz in */ #define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ #if 1 #define CONFIG_8xx_BOOTDELAY -1 /* autoboot disabled */ #define CONFIG_8xx_TFTP_MODE #else #define CONFIG_8xx_BOOTDELAY 5 /* autoboot after 5 seconds */ #undef CONFIG_8xx_TFTP_MODE #endif #define CONFIG_MISC_INIT_R #define CONFIG_DRAM_SPEED (CONFIG_8xx_BUSCLOCK) /* MHz */ #define CONFIG_BOOTCOMMAND "bootm FE020000" /* autoboot command */ #define CONFIG_BOOTARGS " " /* * Miscellaneous configurable options */ #undef CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0800000 /* 4 ... 8 MB in DRAM */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /*----------------------------------------------------------------------- * Internal Memory Mapped Register */ #define CONFIG_SYS_IMMR 0xFFA00000 #define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024)) #define CONFIG_SYS_NVRAM_BASE 0xFA000000 /* NVRAM */ #define CONFIG_SYS_NVRAM_OR 0xffe00000 /* w/o speed dependent flags!! */ #define CONFIG_SYS_CSR_BASE 0xFA100000 /* Control/Status Registers */ #define CONFIG_SYS_PCIMEM_BASE 0x80000000 /* PCI I/O and Memory Spaces */ #define CONFIG_SYS_PCIMEM_OR 0xA0000108 #define CONFIG_SYS_PCIBRIDGE_BASE 0xFA210000 /* PCI-Bus Bridge Registers */ #define CONFIG_SYS_PCIBRIDGE_OR 0xFFFF0108 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR #define CONFIG_SYS_INIT_RAM_END 0x2f00 /* End of used area in DPRAM */ #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */ #define CONFIG_SYS_INIT_VPD_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_VPD_OFFSET-8) /*----------------------------------------------------------------------- * Offset in DPMEM where we keep the VPD data */ #define CONFIG_SYS_DPRAMVPD (CONFIG_SYS_INIT_VPD_OFFSET - 0x2000) /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0x00000000 /*0xFE000000*/ #define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_HWINFO_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_SYS_HWINFO_LEN) #define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 4 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 16 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /*----------------------------------------------------------------------- * NVRAM Configuration * * Note: the MBX is special because there is already a firmware on this * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we * access the NVRAM at the offset 0x1000. */ #define CONFIG_ENV_IS_IN_NVRAM 1 /* turn on NVRAM env feature */ #define CONFIG_ENV_ADDR (CONFIG_SYS_NVRAM_BASE + 0x1000) #define CONFIG_ENV_SIZE 0x1000 /*----------------------------------------------------------------------- * Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- * SYPCR - System Protection Control 11-9 * SYPCR can only be written once after reset! *----------------------------------------------------------------------- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze */ #if defined(CONFIG_WATCHDOG) #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) #else #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF) #endif /*----------------------------------------------------------------------- * SIUMCR - SIU Module Configuration 11-6 *----------------------------------------------------------------------- * PCMCIA config., multi-function pin tri-state */ #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME) /*----------------------------------------------------------------------- * TBSCR - Time Base Status and Control 11-26 *----------------------------------------------------------------------- * Clear Reference Interrupt Status, Timebase freezing enabled */ #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 11-31 *----------------------------------------------------------------------- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled */ #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE) /*----------------------------------------------------------------------- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 *----------------------------------------------------------------------- * Reset PLL lock status sticky bit, timer expired status bit and timer * interrupt status bit - leave PLL multiplication factor unchanged ! */ #define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) /*----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register 15-27 *----------------------------------------------------------------------- * Set clock output, timebase and RTC source and divider, * power management and some other internal clocks */ #define SCCR_MASK (SCCR_RTDIV | SCCR_RTSEL) #define CONFIG_SYS_SCCR SCCR_TBS /*----------------------------------------------------------------------- * *----------------------------------------------------------------------- * */ #define CONFIG_SYS_DER 0 /* Because of the way the 860 starts up and assigns CS0 the * entire address space, we have to set the memory controller * differently. Normally, you write the option register * first, and then enable the chip select by writing the * base register. For CS0, you must write the base register * first, followed by the option register. */ /* * Init Memory Controller: * * BR0/1 and OR0/1 (FLASH) */ /* the other CS:s are determined by looking at parameters in BCSRx */ #define BCSR_ADDR ((uint) 0xFF010000) #define BCSR_SIZE ((uint)(64 * 1024)) #define FLASH_BASE0_PRELIM 0xFE000000 /* FLASH bank #0 */ #define FLASH_BASE1_PRELIM 0xFF010000 /* FLASH bank #0 */ #define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ #define CONFIG_SYS_PRELIM_OR_AM 0xFFF00000 /* OR addr mask */ /* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ #define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) #define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) #define CONFIG_SYS_OR0_PRELIM (0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK) /* 1 Mbyte until detected and only 1 Mbyte is needed*/ #define CONFIG_SYS_BR0_PRELIM (0xFE000000 | BR_V ) /* BCSRx - Board Control and Status Registers */ #define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP #define CONFIG_SYS_OR1_PRELIM 0xFFC00000 | OR_ACS_DIV4 #define CONFIG_SYS_BR1_PRELIM (0x00000000 | BR_MS_UPMA | BR_V ) /* * Memory Periodic Timer Prescaler */ /* periodic timer for refresh */ #define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ #define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ #define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ /* * MAMR settings for SDRAM */ /* 8 column SDRAM */ #define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) /* 9 column SDRAM */ #define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) #define CONFIG_SYS_MAMR 0x13821000 /* * Internal Definitions * * Boot Flags */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ /* values according to the manual */ #define PCMCIA_MEM_ADDR ((uint)0xff020000) #define PCMCIA_MEM_SIZE ((uint)(64 * 1024)) #define BCSR0 ((uint) (BCSR_ADDR + 00)) #define BCSR1 ((uint) (BCSR_ADDR + 0x04)) #define BCSR2 ((uint) (BCSR_ADDR + 0x08)) #define BCSR3 ((uint) (BCSR_ADDR + 0x0c)) #define BCSR4 ((uint) (BCSR_ADDR + 0x10)) /* FADS bitvalues by Helmut Buchsbaum * see MPC8xxADS User's Manual for a proper description * of the following structures */ #define BCSR0_ERB ((uint)0x80000000) #define BCSR0_IP ((uint)0x40000000) #define BCSR0_BDIS ((uint)0x10000000) #define BCSR0_BPS_MASK ((uint)0x0C000000) #define BCSR0_ISB_MASK ((uint)0x01800000) #define BCSR0_DBGC_MASK ((uint)0x00600000) #define BCSR0_DBPC_MASK ((uint)0x00180000) #define BCSR0_EBDF_MASK ((uint)0x00060000) #define BCSR1_FLASH_EN ((uint)0x80000000) #define BCSR1_DRAM_EN ((uint)0x40000000) #define BCSR1_ETHEN ((uint)0x20000000) #define BCSR1_IRDEN ((uint)0x10000000) #define BCSR1_FLASH_CFG_EN ((uint)0x08000000) #define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000) #define BCSR1_BCSR_EN ((uint)0x02000000) #define BCSR1_RS232EN_1 ((uint)0x01000000) #define BCSR1_PCCEN ((uint)0x00800000) #define BCSR1_PCCVCC0 ((uint)0x00400000) #define BCSR1_PCCVPP_MASK ((uint)0x00300000) #define BCSR1_DRAM_HALF_WORD ((uint)0x00080000) #define BCSR1_RS232EN_2 ((uint)0x00040000) #define BCSR1_SDRAM_EN ((uint)0x00020000) #define BCSR1_PCCVCC1 ((uint)0x00010000) #define BCSR2_FLASH_PD_MASK ((uint)0xF0000000) #define BCSR2_DRAM_PD_MASK ((uint)0x07800000) #define BCSR2_DRAM_PD_SHIFT (23) #define BCSR2_EXTTOLI_MASK ((uint)0x00780000) #define BCSR2_DBREVNR_MASK ((uint)0x00030000) #define BCSR3_DBID_MASK ((ushort)0x3800) #define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400) #define BCSR3_BREVNR0 ((ushort)0x0080) #define BCSR3_FLASH_PD_MASK ((ushort)0x0070) #define BCSR3_BREVN1 ((ushort)0x0008) #define BCSR3_BREVN2_MASK ((ushort)0x0003) #define BCSR4_ETHLOOP ((uint)0x80000000) #define BCSR4_TFPLDL ((uint)0x40000000) #define BCSR4_TPSQEL ((uint)0x20000000) #define BCSR4_SIGNAL_LAMP ((uint)0x10000000) #ifdef CONFIG_MPC823 #define BCSR4_USB_EN ((uint)0x08000000) #endif /* CONFIG_MPC823 */ #ifdef CONFIG_MPC860SAR #define BCSR4_UTOPIA_EN ((uint)0x08000000) #endif /* CONFIG_MPC860SAR */ #ifdef CONFIG_MPC860T #define BCSR4_FETH_EN ((uint)0x08000000) #endif /* CONFIG_MPC860T */ #define BCSR4_USB_SPEED ((uint)0x04000000) #define BCSR4_VCCO ((uint)0x02000000) #define BCSR4_VIDEO_ON ((uint)0x00800000) #define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000) #define BCSR4_VIDEO_RST ((uint)0x00200000) #define BCSR4_MODEM_EN ((uint)0x00100000) #define BCSR4_DATA_VOICE ((uint)0x00080000) #define CONFIG_DRAM_40MHZ 1 #ifdef CONFIG_MPC860T /* Interrupt level assignments. */ #define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ #endif /* CONFIG_MPC860T */ /* We don't use the 8259. */ #define NR_8259_INTS 0 #define CONFIG_CMD_NET /* * MPC8xx CPM Options */ #define CONFIG_SCC_ENET 1 #define CONFIG_SCC1_ENET 1 #define CONFIG_FEC_ENET 1 #undef CONFIG_CPM_IIC #undef CONFIG_UCODE_PATCH #define CONFIG_DISK_SPINUP_TIME 1000000 /* PCMCIA configuration */ #define PCMCIA_MAX_SLOTS 2 #ifdef CONFIG_MPC860 #define PCMCIA_SLOT_A 1 #endif #endif /* __CONFIG_H */