/* * Configuation settings for the Freescale MCF5208EVBe. * * Copyright (C) 2004-2008 Freescale Semiconductor, Inc. * TsiChung Liew (Tsi-Chung.Liew@freescale.com) * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef _M5208EVBE_H #define _M5208EVBE_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_MCFUART #define CONFIG_SYS_UART_PORT (0) #define CONFIG_BAUDRATE 115200 #undef CONFIG_WATCHDOG #define CONFIG_WATCHDOG_TIMEOUT 5000 /* Command line configuration */ #include <config_cmd_default.h> #define CONFIG_CMD_CACHE #define CONFIG_CMD_ELF #define CONFIG_CMD_FLASH #undef CONFIG_CMD_I2C #define CONFIG_CMD_MEMORY #define CONFIG_CMD_MISC #define CONFIG_CMD_MII #define CONFIG_CMD_NET #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO #define CONFIG_MCFFEC #ifdef CONFIG_MCFFEC # define CONFIG_MII 1 # define CONFIG_MII_INIT 1 # define CONFIG_SYS_DISCOVER_PHY # define CONFIG_SYS_RX_ETH_BUFFER 8 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN # define CONFIG_HAS_ETH1 # define CONFIG_SYS_FEC0_PINMUX 0 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE # define MCFFEC_TOUT_LOOP 50000 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ # ifndef CONFIG_SYS_DISCOVER_PHY # define FECDUPLEX FULL # define FECSPEED _100BASET # else # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN # endif # endif /* CONFIG_SYS_DISCOVER_PHY */ #endif /* Timer */ #define CONFIG_MCFTMR #undef CONFIG_MCFPIT /* I2C */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_FSL #define CONFIG_SYS_FSL_I2C_SPEED 80000 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ #define CONFIG_UDP_CHECKSUM #ifdef CONFIG_MCFFEC # define CONFIG_ETHADDR 00:e0:0c:bc:e5:60 # define CONFIG_IPADDR 192.162.1.2 # define CONFIG_NETMASK 255.255.255.0 # define CONFIG_SERVERIP 192.162.1.1 # define CONFIG_GATEWAYIP 192.162.1.1 # define CONFIG_OVERWRITE_ETHADDR_ONCE #endif /* CONFIG_MCFFEC */ #define CONFIG_HOSTNAME M5208EVBe #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "loadaddr=40010000\0" \ "u-boot=u-boot.bin\0" \ "load=tftp ${loadaddr) ${u-boot}\0" \ "upd=run load; run prog\0" \ "prog=prot off 0 3ffff;" \ "era 0 3ffff;" \ "cp.b ${loadaddr} 0 ${filesize};" \ "save\0" \ "" #define CONFIG_PRAM 512 /* 512 KB */ #define CONFIG_SYS_PROMPT "-> " #define CONFIG_SYS_LONGHELP /* undef to save memory */ #ifdef CONFIG_CMD_KGDB # define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else # define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buf Sz */ #define CONFIG_SYS_LOAD_ADDR 0x40010000 #define CONFIG_SYS_CLK 166666666 /* CPU Core Clock */ #define CONFIG_SYS_PLL_ODR 0x36 #define CONFIG_SYS_PLL_FDR 0x7D #define CONFIG_SYS_MBAR 0xFC000000 /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) * You should know what you are doing if you make changes here. */ /* Definitions for initial stack pointer and data area (in DPRAM) */ #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in internal SRAM */ #define CONFIG_SYS_INIT_RAM_CTRL 0x221 #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x40000000 #define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ #define CONFIG_SYS_SDRAM_CFG1 0x43711630 #define CONFIG_SYS_SDRAM_CFG2 0x56670000 #define CONFIG_SYS_SDRAM_CTRL 0xE1002000 #define CONFIG_SYS_SDRAM_EMOD 0x80010000 #define CONFIG_SYS_SDRAM_MODE 0x00CD0000 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) #define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20) /* FLASH organization */ #define CONFIG_SYS_FLASH_CFI #ifdef CONFIG_SYS_FLASH_CFI # define CONFIG_FLASH_CFI_DRIVER 1 # define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */ # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ # define CONFIG_SYS_MAX_FLASH_SECT 254 /* max number of sectors on one chip */ # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ #endif #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE /* * Configuration for environment * Environment is embedded in u-boot in the second sector of the flash */ #define CONFIG_ENV_OFFSET 0x2000 #define CONFIG_ENV_SIZE 0x1000 #define CONFIG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_IS_IN_FLASH 1 /* Cache Configuration */ #define CONFIG_SYS_CACHELINE_SIZE 16 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 8) #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - 4) #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ CF_ACR_EN | CF_ACR_SM_ALL) #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ CF_CACR_DISD | CF_CACR_INVI | \ CF_CACR_CEIB | CF_CACR_DCM | \ CF_CACR_EUSP) /* Chipselect bank definitions */ /* * CS0 - NOR Flash * CS1 - Available * CS2 - Available * CS3 - Available * CS4 - Available * CS5 - Available */ #define CONFIG_SYS_CS0_BASE 0 #define CONFIG_SYS_CS0_MASK 0x007F0001 #define CONFIG_SYS_CS0_CTRL 0x00001FA0 #endif /* _M5208EVBE_H */