/* * (C) Copyright 2000-2004 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * David Updegraff, Cray, Inc. dave@cray.com: our 405 is walnut-lite.. * * SPDX-License-Identifier: GPL-2.0+ */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H #define CONFIG_CRAYL1 /* * High Level Configuration Options * (easy to change) */ #define CONFIG_405GP 1 /* This is a PPC405 CPU */ #define CONFIG_4xx 1 /* ...member of PPC405 family */ /* * Note: I make an "image" from U-Boot itself, which prefixes 0x40 * bytes of header info, hence start address is thus shifted. */ #define CONFIG_SYS_TEXT_BASE 0xFFFD0040 #define CONFIG_SYS_CLK_FREQ 25000000 #define CONFIG_BAUDRATE 9600 #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address; handling of ENET */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* early setup for 405gp */ #define CONFIG_MISC_INIT_R 1 /* so that a misc_init_r() is called */ #define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() /* set PRAM to keep U-Boot out, mem= to keep linux out, and initrd_hi to * keep possible initrd ramdisk decompression out. This is in k (1024 bytes) #define CONFIG_PRAM 16 */ #define CONFIG_LOADADDR 0x100000 /* where TFTP images go */ #undef CONFIG_BOOTARGS /* Bootcmd is overridden by the bootscript in board/cray/L1 */ #define CONFIG_SYS_AUTOLOAD "no" #define CONFIG_BOOTCOMMAND "dhcp" /* * ..during experiments.. #define CONFIG_SERVERIP 10.0.0.1 #define CONFIG_ETHADDR 00:40:a6:80:14:5 */ #define CONFIG_HARD_I2C 1 /* hardware support for i2c */ #define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ #define CONFIG_SDRAM_BANK0 1 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_IDENT_STRING "Cray L1" #define CONFIG_ENV_OVERWRITE 1 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_SYS_HUSH_PARSER 1 #define CONFIG_SOURCE 1 /* * Command line configuration. */ #define CONFIG_CMD_ASKENV #define CONFIG_CMD_BDI #define CONFIG_CMD_CONSOLE #define CONFIG_CMD_DATE #define CONFIG_CMD_DHCP #define CONFIG_CMD_DIAG #define CONFIG_CMD_ECHO #define CONFIG_CMD_EEPROM #define CONFIG_CMD_FLASH #define CONFIG_CMD_I2C #define CONFIG_CMD_IMI #define CONFIG_CMD_IMMAP #define CONFIG_CMD_MEMORY #define CONFIG_CMD_NET #define CONFIG_CMD_REGINFO #define CONFIG_CMD_RUN #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_SETGETDCR #define CONFIG_CMD_SOURCE /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_VENDOREX #define CONFIG_BOOTP_DNS #define CONFIG_BOOTP_BOOTFILESIZE /* * how many time to fail & restart a net-TFTP before giving up & resetting * the board hoping that a reset of net interface might help.. */ #define CONFIG_NET_RESET 5 /* * bauds. Just to make it compile; in our case, I read the base_baud * from the DCR anyway, so its kinda-tied to the above ref. clock which in turn * drives the system clock. */ #define CONFIG_SYS_BASE_BAUD 403225 #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} /* * Miscellaneous configurable options */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_LOAD_ADDR 0x100000 /* where to load what we get from TFTP */ #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ #define CONFIG_SYS_DRAM_TEST 1 /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFFC00000 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 192 kB for Monitor */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /* BEG ENVIRONNEMENT FLASH: needs to be a whole FlashSector */ #define CONFIG_ENV_OFFSET 0x3c8000 #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment area */ #define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */ /* Memory tests: U-BOOT relocates itself to the top of Ram, so its at * 32meg-(128k+some_malloc_space+copy-of-ENV sector).. */ #define CONFIG_SYS_SDRAM_SIZE 32 /* megs of ram */ #define CONFIG_SYS_MEMTEST_START 0x2000 /* memtest works from the end of */ /* the exception vector table */ /* to the end of the DRAM */ /* less monitor and malloc area */ #define CONFIG_SYS_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */ #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* 128k for malloc space */ #define CONFIG_SYS_MEM_END_USAGE ( CONFIG_SYS_MONITOR_LEN \ + CONFIG_SYS_MALLOC_LEN \ + CONFIG_ENV_SECT_SIZE \ + CONFIG_SYS_STACK_USAGE ) #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 - CONFIG_SYS_MEM_END_USAGE) /* END ENVIRONNEMENT FLASH */ /* * Init Memory Controller: * * BR0/1 and OR0/1 (FLASH) */ #define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in OnChipMem ) */ #if 1 /* On Chip Memory location */ #define CONFIG_SYS_TEMP_STACK_OCM 1 #define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000 #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #else #define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000 #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */ #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of On Chip SRAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #endif /*----------------------------------------------------------------------- * Definitions for Serial Presence Detect EEPROM address */ #define EEPROM_WRITE_ADDRESS 0xA0 #define EEPROM_READ_ADDRESS 0xA1 #endif /* __CONFIG_H */