/* * (C) Copyright 2005-2008 * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com * * (C) Copyright 2001-2004 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com * * SPDX-License-Identifier: GPL-2.0+ */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_405GP 1 /* This is a PPC405 CPU */ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_APCG405 1 /* ...on a APC405 board */ #define CONFIG_SYS_TEXT_BASE 0xFFF80000 #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ #define CONFIG_BOARD_EARLY_INIT_R 1 #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ #define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */ #define CONFIG_BOARD_TYPES 1 /* support board types */ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 1 /* autoboot after 3 seconds */ #define CONFIG_BOOTCOUNT_LIMIT 1 #undef CONFIG_BOOTARGS #define CONFIG_SYS_USB_LOAD_COMMAND "fatload usb 0 200000 pImage;" \ "fatload usb 0 300000 pImage.initrd" #define CONFIG_SYS_USB_SELF_COMMAND "usb start;run usb_load;usb stop;" \ "run ramargs addip addcon usbargs;" \ "bootm 200000 300000" #define CONFIG_SYS_USB_ARGS "setenv bootargs $(bootargs) usbboot=1" #define CONFIG_SYS_BOOTLIMIT "3" #define CONFIG_SYS_ALT_BOOTCOMMAND "run usb_self;reset" #define CONFIG_EXTRA_ENV_SETTINGS \ "hostname=abg405\0" \ "bd_type=abg405\0" \ "serial#=AA0000\0" \ "kernel_addr=fe000000\0" \ "ramdisk_addr=fe100000\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=$(serverip):$(rootpath)\0" \ "addip=setenv bootargs $(bootargs) " \ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ ":$(hostname)::off panic=1\0" \ "addcon=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)" \ " $(optargs)\0" \ "flash_self=run ramargs addip addcon;" \ "bootm $(kernel_addr) $(ramdisk_addr)\0" \ "net_nfs=tftp 200000 $(img);run nfsargs addip addcon;" \ "bootm\0" \ "rootpath=/tftpboot/abg405/target_root\0" \ "img=/tftpboot/abg405/pImage\0" \ "load=tftp 100000 /tftpboot/abg405/u-boot.bin\0" \ "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \ "cp.b 100000 fff80000 80000\0" \ "ipaddr=10.0.111.111\0" \ "netmask=255.255.0.0\0" \ "serverip=10.0.0.190\0" \ "splashimage=ffe80000\0" \ "usb_load="CONFIG_SYS_USB_LOAD_COMMAND"\0" \ "usb_self="CONFIG_SYS_USB_SELF_COMMAND"\0" \ "usbargs="CONFIG_SYS_USB_ARGS"\0" \ "bootlimit="CONFIG_SYS_BOOTLIMIT"\0" \ "altbootcmd="CONFIG_SYS_ALT_BOOTCOMMAND"\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self;reset" #define CONFIG_ETHADDR 00:02:27:8e:00:00 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #undef CONFIG_HAS_ETH1 #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 #define CONFIG_RESET_PHY_R 1 /* use reset_phy() */ #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_DATE #define CONFIG_CMD_DHCP #define CONFIG_CMD_EEPROM #define CONFIG_CMD_ELF #define CONFIG_CMD_FAT #define CONFIG_CMD_I2C #define CONFIG_CMD_IDE #define CONFIG_CMD_IRQ #define CONFIG_CMD_MII #define CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_SOURCE #define CONFIG_CMD_USB #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION #define CONFIG_SUPPORT_VFAT #define CONFIG_AUTO_UPDATE 1 /* autoupdate via CF or USB */ #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ #define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ #define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() #define CONFIG_SYS_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */ /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 57600, 115200, 230400, 460800, 921600 } #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ /* Only interrupt boot if space is pressed */ /* If a long serial cable is connected but */ /* other end is dead, garbage will be read */ #define CONFIG_AUTOBOOT_KEYED 1 #define CONFIG_AUTOBOOT_PROMPT \ "Press SPACE to abort autoboot in %d seconds\n", bootdelay #undef CONFIG_AUTOBOOT_DELAY_STR #define CONFIG_AUTOBOOT_STOP_STR " " #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ #define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ /* * PCI stuff */ #define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ #define PCI_HOST_FORCE 1 /* configure as pci host */ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ /* resource configuration */ #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ #define CONFIG_PCI_SKIP_HOST_BRIDGE 1 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ #define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ #define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ #define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ /* * IDE/ATA stuff */ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ #define CONFIG_IDE_RESET 1 /* reset for ide supported */ #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS) /* max. 1 drives per IDE bus */ #define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */ /* * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_MONITOR_BASE 0xFFF80000 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ #define CONFIG_SYS_MALLOC_LEN (2*1024*1024) /* Reserve 2MB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Init. Memory map for Linux */ /* * FLASH organization */ #define CONFIG_SYS_FLASH_BASE 0xFE000000 #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 #define CONFIG_SYS_FLASH_QUIET_TEST 1 #define CONFIG_SYS_FLASH_INCREMENT 0x01000000 #define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */ #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { \ {0xfe000000, 0x500000}, \ {0xffe80000, 0x180000} \ } #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CONFIG_SYS_FLASH_BANKS_LIST { \ CONFIG_SYS_FLASH_BASE, \ CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT \ } #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ /* * Environment Variable setup */ #define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ #define CONFIG_ENV_OFFSET 0x000 /* environment starts at the */ /* beginning of the EEPROM */ #define CONFIG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ #define CONFIG_ENV_OVERWRITE 1 /* allow overwriting vendor vars */ #define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ #define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */ /* * I2C EEPROM (CAT24WC16) for environment */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_PPC4XX #define CONFIG_SYS_I2C_PPC4XX_CH0 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ /* 16 byte page write mode using*/ /* last 4 bits of the address */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ /* * External Bus Controller (EBC) Setup */ #define FLASH0_BA (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT) /* FLASH 0 BA */ #define FLASH1_BA CONFIG_SYS_FLASH_BASE /* FLASH 1 Base Address */ #define CAN_BA 0xF0000000 /* CAN Base Address */ #define DUART0_BA 0xF0000400 /* DUART Base Address */ #define DUART1_BA 0xF0000408 /* DUART Base Address */ #define RTC_BA 0xF0000500 /* RTC Base Address */ #define PS2_BA 0xF0000600 /* PS/2 Base Address */ #define CF_BA 0xF0100000 /* CompactFlash Base Address */ #define FPGA_BA 0xF0100100 /* FPGA internal Base Address */ #define FUJI_BA 0xF0100200 /* Fuji internal Base Address */ #define PCMCIA1_BA 0x20000000 /* PCMCIA Slot 1 Base Address */ #define PCMCIA2_BA 0x28000000 /* PCMCIA Slot 2 Base Address */ #define VGA_BA 0xF1000000 /* Epson VGA Base Address */ #define CONFIG_SYS_FPGA_BASE_ADDR FPGA_BA /* FPGA internal Base Address */ /* Memory Bank 0 (Flash Bank 0) initialization */ #define CONFIG_SYS_EBC_PB0AP 0x92015480 #define CONFIG_SYS_EBC_PB0CR FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/ #define CONFIG_SYS_EBC_PB0AP_HWREV8 CONFIG_SYS_EBC_PB0AP #define CONFIG_SYS_EBC_PB0CR_HWREV8 FLASH1_BA | 0xBA000 /* BS=32MB */ /* Memory Bank 1 (Flash Bank 1) initialization */ #define CONFIG_SYS_EBC_PB1AP 0x92015480 #define CONFIG_SYS_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/ /* Memory Bank 2 (CAN0, 1, RTC, Duart) initialization */ #define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ #define CONFIG_SYS_EBC_PB2CR CAN_BA | 0x18000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ /* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization */ #define CONFIG_SYS_EBC_PB3AP 0x010059C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ #define CONFIG_SYS_EBC_PB3CR CF_BA | 0x1A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */ /* Memory Bank 4 (PCMCIA Slot 1) initialization */ #define CONFIG_SYS_EBC_PB4AP 0x050007C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ #define CONFIG_SYS_EBC_PB4CR PCMCIA1_BA | 0xFA000 /*BAS=0x200,BS=128MB,BU=R/W,BW=16bit*/ /* Memory Bank 5 (Epson VGA) initialization */ #define CONFIG_SYS_EBC_PB5AP 0x03805380 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */ #define CONFIG_SYS_EBC_PB5CR VGA_BA | 0x5A000 /* BAS=0xF10,BS=4MB,BU=R/W,BW=16bit */ /* Memory Bank 6 (PCMCIA Slot 2) initialization */ #define CONFIG_SYS_EBC_PB6AP 0x050007C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ #define CONFIG_SYS_EBC_PB6CR PCMCIA2_BA | 0xFA000 /*BAS=0x280,BS=128MB,BU=R/W,BW=16bit*/ /* * FPGA stuff */ /* FPGA internal regs */ #define CONFIG_SYS_FPGA_CTRL 0x008 #define CONFIG_SYS_FPGA_CTRL2 0x00a /* FPGA Control Reg */ #define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0001 #define CONFIG_SYS_FPGA_CTRL_WDI 0x0002 #define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020 #define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ #define CONFIG_SYS_FPGA_MAX_SIZE 80*1024 /* 80kByte is enough for XC2S50 */ /* FPGA program pin configuration */ #define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ #define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ #define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ #define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ #define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ /* * LCD Setup */ #define CONFIG_SYS_LCD_BIG_MEM (VGA_BA + 0x200000) /* S1D13806 Mem Base */ #define CONFIG_SYS_LCD_BIG_REG VGA_BA /* S1D13806 Reg Base */ #define CONFIG_LCD_BIG 2 /* Epson S1D13806 used */ /* Image information... */ #define CONFIG_LCD_USED CONFIG_LCD_BIG #define CONFIG_SYS_LCD_MEM CONFIG_SYS_LCD_BIG_MEM #define CONFIG_SYS_LCD_REG CONFIG_SYS_LCD_BIG_REG #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (1 << 20) /* * Definitions for initial stack pointer and data area (in data cache) */ /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ #define CONFIG_SYS_TEMP_STACK_OCM 1 /* On Chip Memory location */ #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) /* reserve some memory for BOOT limit info */ #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 16) #ifdef CONFIG_BOOTCOUNT_LIMIT /* reserve 2 word for bootcount limit */ #define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 8) #endif /* * PCI OHCI controller */ #define CONFIG_USB_OHCI_NEW 1 #define CONFIG_PCI_OHCI 1 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" #define CONFIG_USB_STORAGE 1 #define CONFIG_SYS_USB_OHCI_BOARD_INIT 1 #endif /* __CONFIG_H */