/* * Copyright (C) 2014 Panasonic Corporation * Copyright (C) 2013-2014, Altera Corporation * Copyright (C) 2009-2010, Intel Corporation and its suppliers. * * SPDX-License-Identifier: GPL-2.0+ */ #include #include #include #include #include #include "denali.h" #define NAND_DEFAULT_TIMINGS -1 static int onfi_timing_mode = NAND_DEFAULT_TIMINGS; /* We define a macro here that combines all interrupts this driver uses into * a single constant value, for convenience. */ #define DENALI_IRQ_ALL (INTR_STATUS__DMA_CMD_COMP | \ INTR_STATUS__ECC_TRANSACTION_DONE | \ INTR_STATUS__ECC_ERR | \ INTR_STATUS__PROGRAM_FAIL | \ INTR_STATUS__LOAD_COMP | \ INTR_STATUS__PROGRAM_COMP | \ INTR_STATUS__TIME_OUT | \ INTR_STATUS__ERASE_FAIL | \ INTR_STATUS__RST_COMP | \ INTR_STATUS__ERASE_COMP | \ INTR_STATUS__ECC_UNCOR_ERR | \ INTR_STATUS__INT_ACT | \ INTR_STATUS__LOCKED_BLK) /* indicates whether or not the internal value for the flash bank is * valid or not */ #define CHIP_SELECT_INVALID -1 #define SUPPORT_8BITECC 1 /* * this macro allows us to convert from an MTD structure to our own * device context (denali) structure. */ #define mtd_to_denali(m) container_of(m->priv, struct denali_nand_info, nand) /* These constants are defined by the driver to enable common driver * configuration options. */ #define SPARE_ACCESS 0x41 #define MAIN_ACCESS 0x42 #define MAIN_SPARE_ACCESS 0x43 #define DENALI_UNLOCK_START 0x10 #define DENALI_UNLOCK_END 0x11 #define DENALI_LOCK 0x21 #define DENALI_LOCK_TIGHT 0x31 #define DENALI_BUFFER_LOAD 0x60 #define DENALI_BUFFER_WRITE 0x62 #define DENALI_READ 0 #define DENALI_WRITE 0x100 /* types of device accesses. We can issue commands and get status */ #define COMMAND_CYCLE 0 #define ADDR_CYCLE 1 #define STATUS_CYCLE 2 /* this is a helper macro that allows us to * format the bank into the proper bits for the controller */ #define BANK(x) ((x) << 24) /* Interrupts are cleared by writing a 1 to the appropriate status bit */ static inline void clear_interrupt(struct denali_nand_info *denali, uint32_t irq_mask) { uint32_t intr_status_reg; intr_status_reg = INTR_STATUS(denali->flash_bank); writel(irq_mask, denali->flash_reg + intr_status_reg); } static uint32_t read_interrupt_status(struct denali_nand_info *denali) { uint32_t intr_status_reg; intr_status_reg = INTR_STATUS(denali->flash_bank); return readl(denali->flash_reg + intr_status_reg); } static void clear_interrupts(struct denali_nand_info *denali) { uint32_t status; status = read_interrupt_status(denali); clear_interrupt(denali, status); denali->irq_status = 0; } static void denali_irq_enable(struct denali_nand_info *denali, uint32_t int_mask) { int i; for (i = 0; i < denali->max_banks; ++i) writel(int_mask, denali->flash_reg + INTR_EN(i)); } static uint32_t wait_for_irq(struct denali_nand_info *denali, uint32_t irq_mask) { unsigned long timeout = 1000000; uint32_t intr_status; do { intr_status = read_interrupt_status(denali) & DENALI_IRQ_ALL; if (intr_status & irq_mask) { denali->irq_status &= ~irq_mask; /* our interrupt was detected */ break; } udelay(1); timeout--; } while (timeout != 0); if (timeout == 0) { /* timeout */ printf("Denali timeout with interrupt status %08x\n", read_interrupt_status(denali)); intr_status = 0; } return intr_status; } /* * Certain operations for the denali NAND controller use an indexed mode to * read/write data. The operation is performed by writing the address value * of the command to the device memory followed by the data. This function * abstracts this common operation. */ static void index_addr(struct denali_nand_info *denali, uint32_t address, uint32_t data) { writel(address, denali->flash_mem + INDEX_CTRL_REG); writel(data, denali->flash_mem + INDEX_DATA_REG); } /* Perform an indexed read of the device */ static void index_addr_read_data(struct denali_nand_info *denali, uint32_t address, uint32_t *pdata) { writel(address, denali->flash_mem + INDEX_CTRL_REG); *pdata = readl(denali->flash_mem + INDEX_DATA_REG); } /* We need to buffer some data for some of the NAND core routines. * The operations manage buffering that data. */ static void reset_buf(struct denali_nand_info *denali) { denali->buf.head = 0; denali->buf.tail = 0; } static void write_byte_to_buf(struct denali_nand_info *denali, uint8_t byte) { denali->buf.buf[denali->buf.tail++] = byte; } /* resets a specific device connected to the core */ static void reset_bank(struct denali_nand_info *denali) { uint32_t irq_status; uint32_t irq_mask = INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT; clear_interrupts(denali); writel(1 << denali->flash_bank, denali->flash_reg + DEVICE_RESET); irq_status = wait_for_irq(denali, irq_mask); if (irq_status & INTR_STATUS__TIME_OUT) debug("reset bank failed.\n"); } /* Reset the flash controller */ static uint32_t denali_nand_reset(struct denali_nand_info *denali) { uint32_t i; for (i = 0; i < denali->max_banks; i++) writel(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT, denali->flash_reg + INTR_STATUS(i)); for (i = 0; i < denali->max_banks; i++) { writel(1 << i, denali->flash_reg + DEVICE_RESET); while (!(readl(denali->flash_reg + INTR_STATUS(i)) & (INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT))) if (readl(denali->flash_reg + INTR_STATUS(i)) & INTR_STATUS__TIME_OUT) debug("NAND Reset operation timed out on bank" " %d\n", i); } for (i = 0; i < denali->max_banks; i++) writel(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT, denali->flash_reg + INTR_STATUS(i)); return 0; } /* * this routine calculates the ONFI timing values for a given mode and * programs the clocking register accordingly. The mode is determined by * the get_onfi_nand_para routine. */ static void nand_onfi_timing_set(struct denali_nand_info *denali, uint16_t mode) { uint32_t trea[6] = {40, 30, 25, 20, 20, 16}; uint32_t trp[6] = {50, 25, 17, 15, 12, 10}; uint32_t treh[6] = {30, 15, 15, 10, 10, 7}; uint32_t trc[6] = {100, 50, 35, 30, 25, 20}; uint32_t trhoh[6] = {0, 15, 15, 15, 15, 15}; uint32_t trloh[6] = {0, 0, 0, 0, 5, 5}; uint32_t tcea[6] = {100, 45, 30, 25, 25, 25}; uint32_t tadl[6] = {200, 100, 100, 100, 70, 70}; uint32_t trhw[6] = {200, 100, 100, 100, 100, 100}; uint32_t trhz[6] = {200, 100, 100, 100, 100, 100}; uint32_t twhr[6] = {120, 80, 80, 60, 60, 60}; uint32_t tcs[6] = {70, 35, 25, 25, 20, 15}; uint32_t tclsrising = 1; uint32_t data_invalid_rhoh, data_invalid_rloh, data_invalid; uint32_t dv_window = 0; uint32_t en_lo, en_hi; uint32_t acc_clks; uint32_t addr_2_data, re_2_we, re_2_re, we_2_re, cs_cnt; en_lo = DIV_ROUND_UP(trp[mode], CLK_X); en_hi = DIV_ROUND_UP(treh[mode], CLK_X); if ((en_hi * CLK_X) < (treh[mode] + 2)) en_hi++; if ((en_lo + en_hi) * CLK_X < trc[mode]) en_lo += DIV_ROUND_UP((trc[mode] - (en_lo + en_hi) * CLK_X), CLK_X); if ((en_lo + en_hi) < CLK_MULTI) en_lo += CLK_MULTI - en_lo - en_hi; while (dv_window < 8) { data_invalid_rhoh = en_lo * CLK_X + trhoh[mode]; data_invalid_rloh = (en_lo + en_hi) * CLK_X + trloh[mode]; data_invalid = data_invalid_rhoh < data_invalid_rloh ? data_invalid_rhoh : data_invalid_rloh; dv_window = data_invalid - trea[mode]; if (dv_window < 8) en_lo++; } acc_clks = DIV_ROUND_UP(trea[mode], CLK_X); while (((acc_clks * CLK_X) - trea[mode]) < 3) acc_clks++; if ((data_invalid - acc_clks * CLK_X) < 2) debug("%s, Line %d: Warning!\n", __FILE__, __LINE__); addr_2_data = DIV_ROUND_UP(tadl[mode], CLK_X); re_2_we = DIV_ROUND_UP(trhw[mode], CLK_X); re_2_re = DIV_ROUND_UP(trhz[mode], CLK_X); we_2_re = DIV_ROUND_UP(twhr[mode], CLK_X); cs_cnt = DIV_ROUND_UP((tcs[mode] - trp[mode]), CLK_X); if (!tclsrising) cs_cnt = DIV_ROUND_UP(tcs[mode], CLK_X); if (cs_cnt == 0) cs_cnt = 1; if (tcea[mode]) { while (((cs_cnt * CLK_X) + trea[mode]) < tcea[mode]) cs_cnt++; } /* Sighting 3462430: Temporary hack for MT29F128G08CJABAWP:B */ if ((readl(denali->flash_reg + MANUFACTURER_ID) == 0) && (readl(denali->flash_reg + DEVICE_ID) == 0x88)) acc_clks = 6; writel(acc_clks, denali->flash_reg + ACC_CLKS); writel(re_2_we, denali->flash_reg + RE_2_WE); writel(re_2_re, denali->flash_reg + RE_2_RE); writel(we_2_re, denali->flash_reg + WE_2_RE); writel(addr_2_data, denali->flash_reg + ADDR_2_DATA); writel(en_lo, denali->flash_reg + RDWR_EN_LO_CNT); writel(en_hi, denali->flash_reg + RDWR_EN_HI_CNT); writel(cs_cnt, denali->flash_reg + CS_SETUP_CNT); } /* queries the NAND device to see what ONFI modes it supports. */ static uint32_t get_onfi_nand_para(struct denali_nand_info *denali) { int i; /* * we needn't to do a reset here because driver has already * reset all the banks before */ if (!(readl(denali->flash_reg + ONFI_TIMING_MODE) & ONFI_TIMING_MODE__VALUE)) return -EIO; for (i = 5; i > 0; i--) { if (readl(denali->flash_reg + ONFI_TIMING_MODE) & (0x01 << i)) break; } nand_onfi_timing_set(denali, i); /* By now, all the ONFI devices we know support the page cache */ /* rw feature. So here we enable the pipeline_rw_ahead feature */ return 0; } static void get_samsung_nand_para(struct denali_nand_info *denali, uint8_t device_id) { if (device_id == 0xd3) { /* Samsung K9WAG08U1A */ /* Set timing register values according to datasheet */ writel(5, denali->flash_reg + ACC_CLKS); writel(20, denali->flash_reg + RE_2_WE); writel(12, denali->flash_reg + WE_2_RE); writel(14, denali->flash_reg + ADDR_2_DATA); writel(3, denali->flash_reg + RDWR_EN_LO_CNT); writel(2, denali->flash_reg + RDWR_EN_HI_CNT); writel(2, denali->flash_reg + CS_SETUP_CNT); } } static void get_toshiba_nand_para(struct denali_nand_info *denali) { uint32_t tmp; /* Workaround to fix a controller bug which reports a wrong */ /* spare area size for some kind of Toshiba NAND device */ if ((readl(denali->flash_reg + DEVICE_MAIN_AREA_SIZE) == 4096) && (readl(denali->flash_reg + DEVICE_SPARE_AREA_SIZE) == 64)) { writel(216, denali->flash_reg + DEVICE_SPARE_AREA_SIZE); tmp = readl(denali->flash_reg + DEVICES_CONNECTED) * readl(denali->flash_reg + DEVICE_SPARE_AREA_SIZE); writel(tmp, denali->flash_reg + LOGICAL_PAGE_SPARE_SIZE); } } static void get_hynix_nand_para(struct denali_nand_info *denali, uint8_t device_id) { uint32_t main_size, spare_size; switch (device_id) { case 0xD5: /* Hynix H27UAG8T2A, H27UBG8U5A or H27UCG8VFA */ case 0xD7: /* Hynix H27UDG8VEM, H27UCG8UDM or H27UCG8V5A */ writel(128, denali->flash_reg + PAGES_PER_BLOCK); writel(4096, denali->flash_reg + DEVICE_MAIN_AREA_SIZE); writel(224, denali->flash_reg + DEVICE_SPARE_AREA_SIZE); main_size = 4096 * readl(denali->flash_reg + DEVICES_CONNECTED); spare_size = 224 * readl(denali->flash_reg + DEVICES_CONNECTED); writel(main_size, denali->flash_reg + LOGICAL_PAGE_DATA_SIZE); writel(spare_size, denali->flash_reg + LOGICAL_PAGE_SPARE_SIZE); writel(0, denali->flash_reg + DEVICE_WIDTH); break; default: debug("Spectra: Unknown Hynix NAND (Device ID: 0x%x)." "Will use default parameter values instead.\n", device_id); } } /* * determines how many NAND chips are connected to the controller. Note for * Intel CE4100 devices we don't support more than one device. */ static void find_valid_banks(struct denali_nand_info *denali) { uint32_t id[denali->max_banks]; int i; denali->total_used_banks = 1; for (i = 0; i < denali->max_banks; i++) { index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 0), 0x90); index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 1), 0); index_addr_read_data(denali, (uint32_t)(MODE_11 | (i << 24) | 2), &id[i]); if (i == 0) { if (!(id[i] & 0x0ff)) break; } else { if ((id[i] & 0x0ff) == (id[0] & 0x0ff)) denali->total_used_banks++; else break; } } } /* * Use the configuration feature register to determine the maximum number of * banks that the hardware supports. */ static void detect_max_banks(struct denali_nand_info *denali) { uint32_t features = readl(denali->flash_reg + FEATURES); denali->max_banks = 2 << (features & FEATURES__N_BANKS); } static void detect_partition_feature(struct denali_nand_info *denali) { /* * For MRST platform, denali->fwblks represent the * number of blocks firmware is taken, * FW is in protect partition and MTD driver has no * permission to access it. So let driver know how many * blocks it can't touch. */ if (readl(denali->flash_reg + FEATURES) & FEATURES__PARTITION) { if ((readl(denali->flash_reg + PERM_SRC_ID(1)) & PERM_SRC_ID__SRCID) == SPECTRA_PARTITION_ID) { denali->fwblks = ((readl(denali->flash_reg + MIN_MAX_BANK(1)) & MIN_MAX_BANK__MIN_VALUE) * denali->blksperchip) + (readl(denali->flash_reg + MIN_BLK_ADDR(1)) & MIN_BLK_ADDR__VALUE); } else { denali->fwblks = SPECTRA_START_BLOCK; } } else { denali->fwblks = SPECTRA_START_BLOCK; } } static uint32_t denali_nand_timing_set(struct denali_nand_info *denali) { uint32_t id_bytes[5], addr; uint8_t i, maf_id, device_id; /* Use read id method to get device ID and other * params. For some NAND chips, controller can't * report the correct device ID by reading from * DEVICE_ID register * */ addr = (uint32_t)MODE_11 | BANK(denali->flash_bank); index_addr(denali, (uint32_t)addr | 0, 0x90); index_addr(denali, (uint32_t)addr | 1, 0); for (i = 0; i < 5; i++) index_addr_read_data(denali, addr | 2, &id_bytes[i]); maf_id = id_bytes[0]; device_id = id_bytes[1]; if (readl(denali->flash_reg + ONFI_DEVICE_NO_OF_LUNS) & ONFI_DEVICE_NO_OF_LUNS__ONFI_DEVICE) { /* ONFI 1.0 NAND */ if (get_onfi_nand_para(denali)) return -EIO; } else if (maf_id == 0xEC) { /* Samsung NAND */ get_samsung_nand_para(denali, device_id); } else if (maf_id == 0x98) { /* Toshiba NAND */ get_toshiba_nand_para(denali); } else if (maf_id == 0xAD) { /* Hynix NAND */ get_hynix_nand_para(denali, device_id); } find_valid_banks(denali); detect_partition_feature(denali); /* If the user specified to override the default timings * with a specific ONFI mode, we apply those changes here. */ if (onfi_timing_mode != NAND_DEFAULT_TIMINGS) nand_onfi_timing_set(denali, onfi_timing_mode); return 0; } /* validation function to verify that the controlling software is making * a valid request */ static inline bool is_flash_bank_valid(int flash_bank) { return flash_bank >= 0 && flash_bank < 4; } static void denali_irq_init(struct denali_nand_info *denali) { uint32_t int_mask = 0; int i; /* Disable global interrupts */ writel(0, denali->flash_reg + GLOBAL_INT_ENABLE); int_mask = DENALI_IRQ_ALL; /* Clear all status bits */ for (i = 0; i < denali->max_banks; ++i) writel(0xFFFF, denali->flash_reg + INTR_STATUS(i)); denali_irq_enable(denali, int_mask); } /* This helper function setups the registers for ECC and whether or not * the spare area will be transferred. */ static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en, bool transfer_spare) { int ecc_en_flag = 0, transfer_spare_flag = 0; /* set ECC, transfer spare bits if needed */ ecc_en_flag = ecc_en ? ECC_ENABLE__FLAG : 0; transfer_spare_flag = transfer_spare ? TRANSFER_SPARE_REG__FLAG : 0; /* Enable spare area/ECC per user's request. */ writel(ecc_en_flag, denali->flash_reg + ECC_ENABLE); /* applicable for MAP01 only */ writel(transfer_spare_flag, denali->flash_reg + TRANSFER_SPARE_REG); } /* sends a pipeline command operation to the controller. See the Denali NAND * controller's user guide for more information (section 4.2.3.6). */ static int denali_send_pipeline_cmd(struct denali_nand_info *denali, bool ecc_en, bool transfer_spare, int access_type, int op) { uint32_t addr, cmd, irq_status; static uint32_t page_count = 1; setup_ecc_for_xfer(denali, ecc_en, transfer_spare); /* clear interrupts */ clear_interrupts(denali); addr = BANK(denali->flash_bank) | denali->page; /* setup the acccess type */ cmd = MODE_10 | addr; index_addr(denali, cmd, access_type); /* setup the pipeline command */ index_addr(denali, cmd, 0x2000 | op | page_count); cmd = MODE_01 | addr; writel(cmd, denali->flash_mem + INDEX_CTRL_REG); if (op == DENALI_READ) { /* wait for command to be accepted */ irq_status = wait_for_irq(denali, INTR_STATUS__LOAD_COMP); if (irq_status == 0) return -EIO; } return 0; } /* helper function that simply writes a buffer to the flash */ static int write_data_to_flash_mem(struct denali_nand_info *denali, const uint8_t *buf, int len) { uint32_t i = 0, *buf32; /* verify that the len is a multiple of 4. see comment in * read_data_from_flash_mem() */ BUG_ON((len % 4) != 0); /* write the data to the flash memory */ buf32 = (uint32_t *)buf; for (i = 0; i < len / 4; i++) writel(*buf32++, denali->flash_mem + INDEX_DATA_REG); return i * 4; /* intent is to return the number of bytes read */ } /* helper function that simply reads a buffer from the flash */ static int read_data_from_flash_mem(struct denali_nand_info *denali, uint8_t *buf, int len) { uint32_t i, *buf32; /* * we assume that len will be a multiple of 4, if not * it would be nice to know about it ASAP rather than * have random failures... * This assumption is based on the fact that this * function is designed to be used to read flash pages, * which are typically multiples of 4... */ BUG_ON((len % 4) != 0); /* transfer the data from the flash */ buf32 = (uint32_t *)buf; for (i = 0; i < len / 4; i++) *buf32++ = readl(denali->flash_mem + INDEX_DATA_REG); return i * 4; /* intent is to return the number of bytes read */ } static void denali_mode_main_access(struct denali_nand_info *denali) { uint32_t addr, cmd; addr = BANK(denali->flash_bank) | denali->page; cmd = MODE_10 | addr; index_addr(denali, cmd, MAIN_ACCESS); } static void denali_mode_main_spare_access(struct denali_nand_info *denali) { uint32_t addr, cmd; addr = BANK(denali->flash_bank) | denali->page; cmd = MODE_10 | addr; index_addr(denali, cmd, MAIN_SPARE_ACCESS); } /* writes OOB data to the device */ static int write_oob_data(struct mtd_info *mtd, uint8_t *buf, int page) { struct denali_nand_info *denali = mtd_to_denali(mtd); uint32_t irq_status; uint32_t irq_mask = INTR_STATUS__PROGRAM_COMP | INTR_STATUS__PROGRAM_FAIL; int status = 0; denali->page = page; if (denali_send_pipeline_cmd(denali, false, true, SPARE_ACCESS, DENALI_WRITE) == 0) { write_data_to_flash_mem(denali, buf, mtd->oobsize); /* wait for operation to complete */ irq_status = wait_for_irq(denali, irq_mask); if (irq_status == 0) { dev_err(denali->dev, "OOB write failed\n"); status = -EIO; } } else { printf("unable to send pipeline command\n"); status = -EIO; } return status; } /* reads OOB data from the device */ static void read_oob_data(struct mtd_info *mtd, uint8_t *buf, int page) { struct denali_nand_info *denali = mtd_to_denali(mtd); uint32_t irq_mask = INTR_STATUS__LOAD_COMP, irq_status = 0, addr = 0x0, cmd = 0x0; denali->page = page; if (denali_send_pipeline_cmd(denali, false, true, SPARE_ACCESS, DENALI_READ) == 0) { read_data_from_flash_mem(denali, buf, mtd->oobsize); /* wait for command to be accepted * can always use status0 bit as the mask is identical for each * bank. */ irq_status = wait_for_irq(denali, irq_mask); if (irq_status == 0) printf("page on OOB timeout %d\n", denali->page); /* We set the device back to MAIN_ACCESS here as I observed * instability with the controller if you do a block erase * and the last transaction was a SPARE_ACCESS. Block erase * is reliable (according to the MTD test infrastructure) * if you are in MAIN_ACCESS. */ addr = BANK(denali->flash_bank) | denali->page; cmd = MODE_10 | addr; index_addr(denali, cmd, MAIN_ACCESS); } } /* this function examines buffers to see if they contain data that * indicate that the buffer is part of an erased region of flash. */ static bool is_erased(uint8_t *buf, int len) { int i = 0; for (i = 0; i < len; i++) if (buf[i] != 0xFF) return false; return true; } /* programs the controller to either enable/disable DMA transfers */ static void denali_enable_dma(struct denali_nand_info *denali, bool en) { uint32_t reg_val = 0x0; if (en) reg_val = DMA_ENABLE__FLAG; writel(reg_val, denali->flash_reg + DMA_ENABLE); readl(denali->flash_reg + DMA_ENABLE); } /* setups the HW to perform the data DMA */ static void denali_setup_dma(struct denali_nand_info *denali, int op) { uint32_t mode; const int page_count = 1; uint32_t addr = (uint32_t)denali->buf.dma_buf; flush_dcache_range(addr, addr + sizeof(denali->buf.dma_buf)); /* For Denali controller that is 64 bit bus IP core */ #ifdef CONFIG_SYS_NAND_DENALI_64BIT mode = MODE_10 | BANK(denali->flash_bank) | denali->page; /* DMA is a three step process */ /* 1. setup transfer type, interrupt when complete, burst len = 64 bytes, the number of pages */ index_addr(denali, mode, 0x01002000 | (64 << 16) | op | page_count); /* 2. set memory low address bits 31:0 */ index_addr(denali, mode, addr); /* 3. set memory high address bits 64:32 */ index_addr(denali, mode, 0); #else mode = MODE_10 | BANK(denali->flash_bank); /* DMA is a four step process */ /* 1. setup transfer type and # of pages */ index_addr(denali, mode | denali->page, 0x2000 | op | page_count); /* 2. set memory high address bits 23:8 */ index_addr(denali, mode | ((uint32_t)(addr >> 16) << 8), 0x2200); /* 3. set memory low address bits 23:8 */ index_addr(denali, mode | ((uint32_t)addr << 8), 0x2300); /* 4. interrupt when complete, burst len = 64 bytes*/ index_addr(denali, mode | 0x14000, 0x2400); #endif } /* Common DMA function */ static uint32_t denali_dma_configuration(struct denali_nand_info *denali, uint32_t ops, bool raw_xfer, uint32_t irq_mask, int oob_required) { uint32_t irq_status = 0; /* setup_ecc_for_xfer(bool ecc_en, bool transfer_spare) */ setup_ecc_for_xfer(denali, !raw_xfer, oob_required); /* clear any previous interrupt flags */ clear_interrupts(denali); /* enable the DMA */ denali_enable_dma(denali, true); /* setup the DMA */ denali_setup_dma(denali, ops); /* wait for operation to complete */ irq_status = wait_for_irq(denali, irq_mask); /* if ECC fault happen, seems we need delay before turning off DMA. * If not, the controller will go into non responsive condition */ if (irq_status & INTR_STATUS__ECC_UNCOR_ERR) udelay(100); /* disable the DMA */ denali_enable_dma(denali, false); return irq_status; } static int write_page(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, bool raw_xfer, int oob_required) { struct denali_nand_info *denali = mtd_to_denali(mtd); uint32_t irq_status = 0; uint32_t irq_mask = INTR_STATUS__DMA_CMD_COMP; denali->status = 0; /* copy buffer into DMA buffer */ memcpy(denali->buf.dma_buf, buf, mtd->writesize); /* need extra memcpy for raw transfer */ if (raw_xfer) memcpy(denali->buf.dma_buf + mtd->writesize, chip->oob_poi, mtd->oobsize); /* setting up DMA */ irq_status = denali_dma_configuration(denali, DENALI_WRITE, raw_xfer, irq_mask, oob_required); /* if timeout happen, error out */ if (!(irq_status & INTR_STATUS__DMA_CMD_COMP)) { debug("DMA timeout for denali write_page\n"); denali->status = NAND_STATUS_FAIL; return -EIO; } if (irq_status & INTR_STATUS__LOCKED_BLK) { debug("Failed as write to locked block\n"); denali->status = NAND_STATUS_FAIL; return -EIO; } return 0; } /* NAND core entry points */ /* * this is the callback that the NAND core calls to write a page. Since * writing a page with ECC or without is similar, all the work is done * by write_page above. */ static int denali_write_page(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required) { struct denali_nand_info *denali = mtd_to_denali(mtd); /* * for regular page writes, we let HW handle all the ECC * data written to the device. */ if (oob_required) /* switch to main + spare access */ denali_mode_main_spare_access(denali); else /* switch to main access only */ denali_mode_main_access(denali); return write_page(mtd, chip, buf, false, oob_required); } /* * This is the callback that the NAND core calls to write a page without ECC. * raw access is similar to ECC page writes, so all the work is done in the * write_page() function above. */ static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required) { struct denali_nand_info *denali = mtd_to_denali(mtd); /* * for raw page writes, we want to disable ECC and simply write * whatever data is in the buffer. */ if (oob_required) /* switch to main + spare access */ denali_mode_main_spare_access(denali); else /* switch to main access only */ denali_mode_main_access(denali); return write_page(mtd, chip, buf, true, oob_required); } static int denali_write_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { return write_oob_data(mtd, chip->oob_poi, page); } /* raw include ECC value and all the spare area */ static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { struct denali_nand_info *denali = mtd_to_denali(mtd); uint32_t irq_status, irq_mask = INTR_STATUS__DMA_CMD_COMP; if (denali->page != page) { debug("Missing NAND_CMD_READ0 command\n"); return -EIO; } if (oob_required) /* switch to main + spare access */ denali_mode_main_spare_access(denali); else /* switch to main access only */ denali_mode_main_access(denali); /* setting up the DMA where ecc_enable is false */ irq_status = denali_dma_configuration(denali, DENALI_READ, true, irq_mask, oob_required); /* if timeout happen, error out */ if (!(irq_status & INTR_STATUS__DMA_CMD_COMP)) { debug("DMA timeout for denali_read_page_raw\n"); return -EIO; } /* splitting the content to destination buffer holder */ memcpy(chip->oob_poi, (denali->buf.dma_buf + mtd->writesize), mtd->oobsize); memcpy(buf, denali->buf.dma_buf, mtd->writesize); return 0; } static int denali_read_page(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { struct denali_nand_info *denali = mtd_to_denali(mtd); uint32_t irq_status, irq_mask = INTR_STATUS__DMA_CMD_COMP; if (denali->page != page) { debug("Missing NAND_CMD_READ0 command\n"); return -EIO; } if (oob_required) /* switch to main + spare access */ denali_mode_main_spare_access(denali); else /* switch to main access only */ denali_mode_main_access(denali); /* setting up the DMA where ecc_enable is true */ irq_status = denali_dma_configuration(denali, DENALI_READ, false, irq_mask, oob_required); memcpy(buf, denali->buf.dma_buf, mtd->writesize); /* check whether any ECC error */ if (irq_status & INTR_STATUS__ECC_UNCOR_ERR) { /* is the ECC cause by erase page, check using read_page_raw */ debug(" Uncorrected ECC detected\n"); denali_read_page_raw(mtd, chip, buf, oob_required, denali->page); if (is_erased(buf, mtd->writesize) == true && is_erased(chip->oob_poi, mtd->oobsize) == true) { debug(" ECC error cause by erased block\n"); /* false alarm, return the 0xFF */ } else { return -EIO; } } memcpy(buf, denali->buf.dma_buf, mtd->writesize); return 0; } static int denali_read_oob(struct mtd_info *mtd, struct nand_chip *chip, int page) { read_oob_data(mtd, chip->oob_poi, page); return 0; } static uint8_t denali_read_byte(struct mtd_info *mtd) { struct denali_nand_info *denali = mtd_to_denali(mtd); uint32_t addr, result; addr = (uint32_t)MODE_11 | BANK(denali->flash_bank); index_addr_read_data(denali, addr | 2, &result); return (uint8_t)result & 0xFF; } static void denali_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) { struct denali_nand_info *denali = mtd_to_denali(mtd); uint32_t i, addr, result; /* delay for tR (data transfer from Flash array to data register) */ udelay(25); /* ensure device completed else additional delay and polling */ wait_for_irq(denali, INTR_STATUS__INT_ACT); addr = (uint32_t)MODE_11 | BANK(denali->flash_bank); for (i = 0; i < len; i++) { index_addr_read_data(denali, (uint32_t)addr | 2, &result); write_byte_to_buf(denali, result); } memcpy(buf, denali->buf.buf, len); } static void denali_select_chip(struct mtd_info *mtd, int chip) { struct denali_nand_info *denali = mtd_to_denali(mtd); denali->flash_bank = chip; } static int denali_waitfunc(struct mtd_info *mtd, struct nand_chip *chip) { struct denali_nand_info *denali = mtd_to_denali(mtd); int status = denali->status; denali->status = 0; return status; } static void denali_erase(struct mtd_info *mtd, int page) { struct denali_nand_info *denali = mtd_to_denali(mtd); uint32_t cmd, irq_status; /* clear interrupts */ clear_interrupts(denali); /* setup page read request for access type */ cmd = MODE_10 | BANK(denali->flash_bank) | page; index_addr(denali, cmd, 0x1); /* wait for erase to complete or failure to occur */ irq_status = wait_for_irq(denali, INTR_STATUS__ERASE_COMP | INTR_STATUS__ERASE_FAIL); if (irq_status & INTR_STATUS__ERASE_FAIL || irq_status & INTR_STATUS__LOCKED_BLK) denali->status = NAND_STATUS_FAIL; else denali->status = 0; } static void denali_cmdfunc(struct mtd_info *mtd, unsigned int cmd, int col, int page) { struct denali_nand_info *denali = mtd_to_denali(mtd); uint32_t addr; switch (cmd) { case NAND_CMD_PAGEPROG: break; case NAND_CMD_STATUS: addr = MODE_11 | BANK(denali->flash_bank); index_addr(denali, addr | 0, cmd); break; case NAND_CMD_READID: case NAND_CMD_PARAM: reset_buf(denali); /* sometimes ManufactureId read from register is not right * e.g. some of Micron MT29F32G08QAA MLC NAND chips * So here we send READID cmd to NAND insteand * */ addr = MODE_11 | BANK(denali->flash_bank); index_addr(denali, addr | 0, cmd); index_addr(denali, addr | 1, col & 0xFF); if (cmd == NAND_CMD_PARAM) udelay(50); break; case NAND_CMD_RNDOUT: addr = MODE_11 | BANK(denali->flash_bank); index_addr(denali, addr | 0, cmd); index_addr(denali, addr | 1, col & 0xFF); index_addr(denali, addr | 1, col >> 8); index_addr(denali, addr | 0, NAND_CMD_RNDOUTSTART); break; case NAND_CMD_READ0: case NAND_CMD_SEQIN: denali->page = page; break; case NAND_CMD_RESET: reset_bank(denali); break; case NAND_CMD_READOOB: /* TODO: Read OOB data */ break; case NAND_CMD_ERASE1: /* * supporting block erase only, not multiblock erase as * it will cross plane and software need complex calculation * to identify the block count for the cross plane */ denali_erase(mtd, page); break; case NAND_CMD_ERASE2: /* nothing to do here as it was done during NAND_CMD_ERASE1 */ break; case NAND_CMD_UNLOCK1: addr = MODE_10 | BANK(denali->flash_bank) | page; index_addr(denali, addr | 0, DENALI_UNLOCK_START); break; case NAND_CMD_UNLOCK2: addr = MODE_10 | BANK(denali->flash_bank) | page; index_addr(denali, addr | 0, DENALI_UNLOCK_END); break; case NAND_CMD_LOCK: addr = MODE_10 | BANK(denali->flash_bank); index_addr(denali, addr | 0, DENALI_LOCK); break; default: printf(": unsupported command received 0x%x\n", cmd); break; } } /* end NAND core entry points */ /* Initialization code to bring the device up to a known good state */ static void denali_hw_init(struct denali_nand_info *denali) { /* * tell driver how many bit controller will skip before writing * ECC code in OOB. This is normally used for bad block marker */ writel(CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES, denali->flash_reg + SPARE_AREA_SKIP_BYTES); detect_max_banks(denali); denali_nand_reset(denali); writel(0x0F, denali->flash_reg + RB_PIN_ENABLED); writel(CHIP_EN_DONT_CARE__FLAG, denali->flash_reg + CHIP_ENABLE_DONT_CARE); writel(0xffff, denali->flash_reg + SPARE_AREA_MARKER); /* Should set value for these registers when init */ writel(0, denali->flash_reg + TWO_ROW_ADDR_CYCLES); writel(1, denali->flash_reg + ECC_ENABLE); denali_nand_timing_set(denali); denali_irq_init(denali); } static struct nand_ecclayout nand_oob; static int denali_init(struct denali_nand_info *denali) { int ret; denali_hw_init(denali); denali->mtd->name = "denali-nand"; denali->mtd->owner = THIS_MODULE; denali->mtd->priv = &denali->nand; /* register the driver with the NAND core subsystem */ denali->nand.select_chip = denali_select_chip; denali->nand.cmdfunc = denali_cmdfunc; denali->nand.read_byte = denali_read_byte; denali->nand.read_buf = denali_read_buf; denali->nand.waitfunc = denali_waitfunc; /* * scan for NAND devices attached to the controller * this is the first stage in a two step process to register * with the nand subsystem */ if (nand_scan_ident(denali->mtd, denali->max_banks, NULL)) { ret = -ENXIO; goto fail; } #ifdef CONFIG_SYS_NAND_USE_FLASH_BBT /* check whether flash got BBT table (located at end of flash). As we * use NAND_BBT_NO_OOB, the BBT page will start with * bbt_pattern. We will have mirror pattern too */ denali->nand.bbt_options |= NAND_BBT_USE_FLASH; /* * We are using main + spare with ECC support. As BBT need ECC support, * we need to ensure BBT code don't write to OOB for the BBT pattern. * All BBT info will be stored into data area with ECC support. */ denali->nand.bbt_options |= NAND_BBT_NO_OOB; #endif denali->nand.ecc.mode = NAND_ECC_HW; denali->nand.ecc.size = CONFIG_NAND_DENALI_ECC_SIZE; /* * Tell driver the ecc strength. This register may be already set * correctly. So we read this value out. */ denali->nand.ecc.strength = readl(denali->flash_reg + ECC_CORRECTION); switch (denali->nand.ecc.size) { case 512: denali->nand.ecc.bytes = (denali->nand.ecc.strength * 13 + 15) / 16 * 2; break; case 1024: denali->nand.ecc.bytes = (denali->nand.ecc.strength * 14 + 15) / 16 * 2; break; default: pr_err("Unsupported ECC size\n"); ret = -EINVAL; goto fail; } nand_oob.eccbytes = denali->nand.ecc.bytes; denali->nand.ecc.layout = &nand_oob; writel(denali->mtd->erasesize / denali->mtd->writesize, denali->flash_reg + PAGES_PER_BLOCK); writel(denali->nand.options & NAND_BUSWIDTH_16 ? 1 : 0, denali->flash_reg + DEVICE_WIDTH); writel(denali->mtd->writesize, denali->flash_reg + DEVICE_MAIN_AREA_SIZE); writel(denali->mtd->oobsize, denali->flash_reg + DEVICE_SPARE_AREA_SIZE); if (readl(denali->flash_reg + DEVICES_CONNECTED) == 0) writel(1, denali->flash_reg + DEVICES_CONNECTED); /* override the default operations */ denali->nand.ecc.read_page = denali_read_page; denali->nand.ecc.read_page_raw = denali_read_page_raw; denali->nand.ecc.write_page = denali_write_page; denali->nand.ecc.write_page_raw = denali_write_page_raw; denali->nand.ecc.read_oob = denali_read_oob; denali->nand.ecc.write_oob = denali_write_oob; if (nand_scan_tail(denali->mtd)) { ret = -ENXIO; goto fail; } ret = nand_register(0); fail: return ret; } static int __board_nand_init(void) { struct denali_nand_info *denali; denali = kzalloc(sizeof(*denali), GFP_KERNEL); if (!denali) return -ENOMEM; /* * If CONFIG_SYS_NAND_SELF_INIT is defined, each driver is responsible * for instantiating struct nand_chip, while drivers/mtd/nand/nand.c * still provides a "struct mtd_info nand_info" instance. */ denali->mtd = &nand_info[0]; /* * In the future, these base addresses should be taken from * Device Tree or platform data. */ denali->flash_reg = (void __iomem *)CONFIG_SYS_NAND_REGS_BASE; denali->flash_mem = (void __iomem *)CONFIG_SYS_NAND_DATA_BASE; return denali_init(denali); } void board_nand_init(void) { if (__board_nand_init() < 0) pr_warn("Failed to initialize Denali NAND controller.\n"); }